The previous patch which implemented a DT binding for sdhci-tegra did not
allow all platform data fields to be initialized from DT. The following
were missing:

is_8bit: Implemented by this patch.

pm_flags: Not implemented yet. There are no mainline users of this field.
  I'm not quite sure what it's for, and hence how to represent this
  in DT; the value ends up being assigned to host->mmc->pm_caps.

While we're at it, fix the binding documentation to refer to "SD/MMC"
instead of "eSDHC", since that's the correct name; "eSDHC" was cut/paste
from the Freescale binding docs.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The Patch adds the support for SDIO interrupts for all slots.
It includes enabling of SDIO interrupts through dw_mci_enable_sdio_irq
and the handling of the slot specific interrupts in the Interrupt Service
Routine.
Signed-off-by: NShashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

If DMA resource is not available then SDCC driver
should atleast work in PIO data transfer mode.
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Intialize busclk_timer before it is accessed in probe.
Signed-off-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Not all targets have IRQ1 line routed from the SD controller to
the processor. So we cannot rely on IRQ1 for PIO interrupts.
This patch moves all PIO interrupts to IRQ0 and enables the PIO
mode.
Signed-off-by: NMurali Palnati <palnatim@codeaurora.org>
Signed-off-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

On some targets, MCI_IRQ_MASK1 is not routed to the MSM in which
case only "cmd_irq" must be used even for PIO. With this change,
all the targets will use only "cmd_irq" for both CMD and PIO.
Signed-off-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

For clocks that support rates which can be set (most clocks other
than _pclk AHB clocks), a rate must be set using clk_set_rate()
before the clock is enabled for the first time with clk_enable().
Subsequent calls to clk_enable() need not be preceded with the
clk_set_rate() calls unless we wish to change the clock rate that
is set previously.

SDC host->clk is currently enabled without setting the clock rate
even once. This patch fixes this, by ensuring that the clock rate
for this clock is first set before enabling the clock.
Signed-off-by: NMurali Palnati <palnatim@codeaurora.org>
Signed-off-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This allows boards with non-standard sdio cards to fill the CIS/CCCR data.
It is particularly important for old msm72k boards using wl1251.
Also drop the obsolete embedded_sdio_data structure from the header
as it was intended to surve a similiar purpose but was not implemented.
Signed-off-by: NAlexander Tarasikov <alexander.tarasikov@gmail.com>
Acked-by: NSahitya Tummala <stummala@codeaurora.org>
[davidb: minor formatting cleanup]
Signed-off-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

The use of && instead of || caused a NULL pointer dereference if
gpio setup was not passed via platform data
Signed-off-by: NAlexander Tarasikov <alexander.tarasikov@gmail.com>
Acked-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This allows specific (non-multiplexed) IRQ handlers to be used.

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: NMagnus Damm <magnus.damm@gmail.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NChris Ball <cjb@laptop.org>

Allow named IRQs to use corresponding specific handlers. If named IRQs are
used, at least an "sdcard" IRQ has to be specified by the platform. If
names are not used, an arbitrary number of IRQs can be provided by the
platform, in which case the generic ISR will be used for each of them.

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NMagnus Damm <magnus.damm@gmail.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>
[g.liakhovetski@gmx.de: style and typo corrections, platform data check]
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Provide separate interrupt handlers which may be used by platforms where
SDHI has three interrupt sources.

This patch also removes the commented-out handling of CRC and other errors.

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NMagnus Damm <magnus.damm@gmail.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NChris Ball <cjb@laptop.org>

This avoids the need to look up the masks each time an interrupt is handled.
As suggested by Guennadi.

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NMagnus Damm <magnus.damm@gmail.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NChris Ball <cjb@laptop.org>

Fix the sparse warning output "warning: Using plain integer as NULL pointer"
Signed-off-by: NVenkatraman S <svenkatr@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Fix the sparse warning "drivers/mmc/card/queue.c:111:20: warning:
symbol 'mmc_alloc_sg' was not declared. Should it be static?"
Signed-off-by: NVenkatraman S <svenkatr@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The individual SoC dependency in Kconfig hardly scales anymore.
Instead of having such a fine grained dependency just depend
on ARCH_MXC and risk that the uninformed user has to look in
the help text to figure out which driver is the correct one.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add hooks to read gpio configuration out of the device tree node.

[grant.likely: Rewrite of original patch from John Bonesio]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
[swarren: Fixed tegra_sdhci_get_ro() to retrieve pdata correctly]
[swarren: Reworked to avoid #ifdef CONFIG_OF]
[swarren: Reworked binding based on fsl-imx-esdhc.txt]
[swarren: Documented binding]
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Now that we have improved the runtime power management powerup/powerdown
code, we believe that MMC_CAP_POWER_OFF_CARD is no longer necessary:
runtime PM should now work everywhere.

The only hard evidence for introducing MMC_CAP_POWER_OFF_CARD was the
Marvell sd8686 wifi chip, which was believed to require external gpio
manipulation which wasn't supported by some boards.

After further investigation it was realized (and confirmed by Marvell
folks) that sd8686 requirements can be fulfilled by changing the reset
sequence itself, even if no external gpio is manipulated.

For further information, see the following thread:
http://www.mail-archive.com/linux-mmc@vger.kernel.org/msg04289.html

Enable this trivially for a release or two. If no problems are reported,
we will follow up with a more extensive patch to remove this flag
altogether. If problems are reported, we can look at whitelist/blacklist
possibilities as before.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Acked-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add description on how to enable random fault injection
for MMC IO.
Signed-off-by: NPer Forlin <per.forlin@linaro.org>
Acked-by: NAkinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This adds support to inject data errors after a completed host transfer.
The mmc core will return error even though the host transfer is successful.
This simple fault injection proved to be very useful to test the
non-blocking error handling in the mmc_blk_issue_rw_rq().
Random faults can also test how the host driver handles pre_req()
and post_req() in case of errors.
Signed-off-by: NPer Forlin <per.forlin@linaro.org>
Acked-by: NAkinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Export symbols should_fail() and fault_create_debugfs_attr() in order
to let modules utilize the fault injection framework.
Signed-off-by: NPer Forlin <per.forlin@linaro.org>
Acked-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Eanble the ADMA2 mode for freescale esdhc imx driver, tested on MX25
3DS board, MX51 BBG board and MX53 LOCO board.

This patch is only used to enable the ADMA2 for MX51/53 platforms.
MX25/35 can't support the ADMA2 mode, set BROKEN_ADMA quirk on
MX25/35 platforms.

The ADMA mode supported or not can be distinguished by bit 20 of
the Capability Register (offset 0x40) in the FSL eSDHC module.
Signed-off-by: NRichard Zhu <richard.zhu@linaro.org>
Tested-and-acked-by: NEric Miao <eric.miao@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Remove the use of irq_to_gpio() in the card detection interrupt
handler. The information is available in the board structure and
we can avoid using a function that has little meaning.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch fixes a potential issue about PDC interrupts. For example we
have a ENDRX pending interrupt and a RXBUFF pending interrupt. We have
received the RXBUFF interrupt but the transfer is not finished (so we
didn't have time to give a new buffer to the PDC controller). Then we
will compute ENDRX interrupt and we will give a new buffer to the PDC
controller, just after we will compute the RXBUFF interrupt and give
one or two new buffers to the PDC controller but we are not sure that
the first buffer given has been filled. So in this situation we may
have "lost" one sg buffer. It's the same for transmission.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Assuming that a sg buffer size is a page size is false so use sg_dma_len.
A 4096 bytes can be required with two 2048-bytes sg buffer.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Rename atmci_start_command() to atmci_send_command() which is more
appropriate; atmci_start_command suggests we're sending a start command.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add pdc support for atmel-mci. It makes at91-mci driver useless because it
was only used for the old atmel MCI core which has pdc but no dma support.
To allow removing at91-mci, the capabilities of the MCI core are detected
at runtime -- then the driver will use pio, pdc or dma transfers.
Warning: at91rm9200 is not supported, to support it we need to use swab32
on data but I have no board to test it.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Change atmci_readl and atmci_writel macros: remove string concatenation.
We can use these macros with registers which are not prefixed by ATMCI_.
This is the case if we want to write PDC registers which are common to
several devices so they are not prefixed with ATMCI_.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Homogenize namespace to atmci.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Private rx_csum flags are now duplicate of netdev->features & NETIF_F_RXCSUM.
Removing this needs deeper surgery.

Things noticed:
 - HW VLAN acceleration probably can be toggled, but it's left as is
 - the resets on RX csum offload change can probably be avoided
 - there is A LOT of copy-and-pasted code here
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When enabling hardware timestamping for ptp v2 event packets, the
software does not setup the queue for l4 packets, although layer 4
packets are valid for v2. This patch adds the flag which enables
setting up a queue and enabling udp packet timestamping.
Signed-off-by: NJacob E Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implements the new netdev op to allow user configuration of spoof
checking on a per VF basis.

V2 - Change netdev spoof check op setting to bool
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add configuration setting for drivers to turn spoof checking on or off
for discrete VFs.

v2 - Fix indentation problem, wrap the ifla_vf_info structure in
     #ifdef __KERNEL__ to prevent user space from accessing and
     change function paramater for the spoof check setting netdev
     op from u8 to bool.
v3 - Preset spoof check setting to -1 so that user space tools such
     as ip can detect that the driver didn't report a spoofcheck
     setting.  Prevents incorrect display of spoof check settings
     for drivers that don't report it.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 67fd4fcb (e1000e: convert to stats64) added the ability to update
statistics more accurately and on-demand through the net_device_ops
.ndo_get_stats64 hook, but introduced a locking bug on 82577/8/9 when
linked at half-duplex (seen on kernels with CONFIG_DEBUG_ATOMIC_SLEEP=y and
CONFIG_PROVE_LOCKING=y).  The commit introduced code paths that caused a
mutex to be locked in atomic contexts, e.g. an rcu_read_lock is held when
irqbalance reads the stats from /sys/class/net/ethX/statistics causing the
mutex to be locked to read the Phy half-duplex statistics registers.

The mutex was originally introduced to prevent concurrent accesses of
resources (the NVM and Phy) shared by the driver, firmware and hardware
a few years back when there was an issue with the NVM getting corrupted.
It was later split into two mutexes - one for the NVM and one for the Phy
when it was determined the NVM, unlike the Phy, should not be protected by
the software/firmware/hardware semaphore (arbitration of which is done in
part with the SWFLAG bit in the EXTCNF_CTRL register).  This latter
semaphore should be sufficient to prevent resource contention of the Phy in
the driver (i.e. the mutex for Phy accesses is not needed), but to be sure
the mutex is replaced with an atomic bit flag which will warn if any
contention is possible.

Also add additional debug output to help determine when the sw/fw/hw
semaphore is owned by the firmware or hardware.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Reported-by: NFrancois Romieu <romieu@fr.zoreil.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>

The recent changes to only power the device when the interface up
introduced a bug: changing interface type, legal when the interface
is down, performs device I/O.

Fix this functionality by validating and recording the interface
type when the change is requested, but only applying the change
if/when the interface is brought up.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Only station flags that are already defined in nl80211 are added for
now.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>