Enable ELAN0100 touchpad driver, found on a Asus X205TA laptop, to
gai 2,3 fingers tap and 2 fingers scroll.
Signed-off-by: NMichele Curti <michele.curti@gmail.com>
Reviewed-by: NDuson Lin <dusonlin@emc.com.tw>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

When trying to disable a key that is not supported by the device we should
report error, not do nothing and report success:

root@yocto:/sys/devices/soc0/gpio-keys# cat keys
114-116
root@yocto:/sys/devices/soc0/gpio-keys# echo 77 > keys
root@yocto:/sys/devices/soc0/gpio-keys#

We want 'echo 77 > keys' to report an error, but silence to give us an
illusion that all is 'ok'.
Signed-off-by: NPeng Fan <van.freenix@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Propagate error code on failure, or upper layers will be confused by
returned 0 (success) code.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

I have a static checker that complains when we check for an upper bound
but don't have a corresponding check for a lower bound.  With this code,
the upper bound check seems not really required, so it is not a bug to
leave the lower bound check out as well.  But let's silence the warning
by making these variables unsigned.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of custom zhenhua_bitreverse() let's use generic bitrev8().
Signed-off-by: NYalin Wang <yalin.wang2010@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The ChromeOS EC keyboard driver config depends on CROS_EC_PROTO but
MFD_CROS_EC selects CROS_EC_PROTO instead. Mixing select and depends
on is bad practice as it may lead to circular Kconfig dependencies.

Since the platform device that is matched with the keyboard driver
is registered by the ChromeOS EC mfd driver, KEYBOARD_CROS_EC really
should depend on MFD_CROS_EC. And because this config option selects
CROS_EC_PROTO, that dependency is met as well. So make the driver
to depend on MFD_CROS_EC instead of CROS_EC_PROTO.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Several cap11xx variants have LEDs that be can be controlled; let's plug
the driver into the LED subsystem.
Signed-off-by: NMatt Ranostay <mranostay@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Flags are now mandatory for devm_gpiod_get(). So let's use proper flag
to configure gpio for output instead of doing this by hand.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
[Dmitry: GPIOD_ASIS -> GPIOD_OUT_LOW]
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

It takes a bit of time to go through controller power up sequence and
initialization. To not stall the overall boot progress let's probe the
controller asynchronously, given that userspace is usually prepared for
hot-plugging of input devices and thus does not rely on particular
ordering.
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

It takes a bit of time to go through controller power up sequence and
initialization. To not stall the overall boot progress let's probe the
controller asynchronously, given that userspace is usually prepared for
hot-plugging of input devices and thus does not rely on particular
ordering.
Signed-off-by: NDmitry Torokhov <dtor@chromium.org>
Reviewed-by: NBenson Leung <bleung@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Elan touchscreen controllers use two power supplies, vcc33 and vccio,
and we need to enable them before trying to access the device. On X86
firmware usually does this, but on ARM it is usually left to the kernel.
Signed-off-by: NDmitry Torokhov <dtor@chromium.org>
Reviewed-by: NBenson Leung <bleung@chromium.org>
Reviewed-by: NScott Liu <scott.liu@emc.com.tw>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Do not emit EV_SYN/SYN_REPORT on suspend if there were no keys that are
still pressed as we are suspending the device (and in all other cases when
input core is forcibly releasing keys via input_dev_release_keys() call).
Reviewed-by: NBenson Leung <bleung@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

If the device is in idle mode and is in the middle of a scan it may not
have a chance to react to the reset and then IAP commands within required
time interval and firmware update may fail. Let's bring the device out of
idle mode before attempting to reset it so that the scan period is smaller
and thus it can react to the command quicker.
Signed-off-by: NJames Chen <james.chen@emc.com.tw>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This indicates the device coordinates should be directly mapped to screen.
This is valid since scaling/flipping/rotation should be done by configuring
the MXT device.

It also flags to Android using INPUT_PROP_DIRECT that the device should be
treated as a touch screen by default, and removes the necessity for a
default IDC file.
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The CHG/interrupt line is momentarily set (approximately 100 ms) as an
input after power-up or reset for diagnostic purposes. This may cause
spurious interrupts, so disable interrupt handler during this period.
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Use function rather than loop, define np to reduce wrapping.
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

input_dev may be NULL if mxt_initialize_input_device fails. But pm ops is
still available and suspend/resume assume
input_dev is not NULL. To fix this issue, we add a check if (!input_dev).
Signed-off-by: NPan Xinhui <xinhuix.pan@intel.com>
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Many of these values are out of date and they aren't used in the driver
- all they do is increase the size of the kernel source.
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Acked-by: NBenson Leung <bleung@chromium.org>
Acked-by: NYufeng Shen <miletus@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The hardcoded 0x83 CTRL setting overrides other settings in that byte,
enabling extra reporting that may not be useful on a particular platform.

Implement improved suspend mechanism via deep sleep. By writing zero to
both the active and idle cycle times the maXTouch device can be put into a
deep sleep mode, using minimal power. It is necessary to issue a calibrate
command after the chip has spent any time in deep sleep, however a soft
reset is unnecessary.

Use the old method on Chromebook Pixel via platform data option.

This patch also deals with the situation where the power configuration is
zero on probe, which would mean that the device never wakes up to execute
commands.

After a config download, the T7 power configuration may have changed so it
is necessary to re-read it.
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Acked-by: NBenson Leung <bleung@chromium.org>
Acked-by: NYufeng Shen <miletus@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.

Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add support for hardware which uses an I2C Serializer / Deserializer
(SerDes) to communicate with the zFroce touch driver. In this case the
SerDes will be configured as an interrupt controller and the zForce driver
will have no access to poll the GPIO line.

To support this, we add two dedicated new GPIOs in the device tree:
reset-gpios and irq-gpios, with the irq-gpios being optional.

To not break the existing device trees, the index based 'gpios' entries
are still supported, but marked as deprecated.

With this, if the interrupt GPIO is available, either via the old or new
device tree style, the while loop will read and handle the packets as long
as the GPIO indicates that the interrupt is asserted (existing, unchanged
driver behavior).

If the interrupt GPIO isn't available, i.e. not configured via the new
device tree style, we are falling back to one read per ISR invocation
(new behavior to support the SerDes).

Note that the gpiod functions help to handle the optional GPIO:
devm_gpiod_get_index_optional() will return NULL in case the interrupt
GPIO isn't available. And gpiod_get_value_cansleep() does cover this, too,
by returning 0 in this case.
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: NHeiko Stuebner <heiko.stuebner@bq.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Avoid the driver generate warning message when the cyapa driver working
with the old Gen5 trackpad device which does not support the proximity
function.  Those old Gen5 trackpad device all have the platform version
less than 2.
Signed-off-by: NDudley Du <dudl@cypress.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add device tree support for  Cypress trackpad devices.
Signed-off-by: NDudley Du <dudl@cypress.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

We need to power up the chip before we can initialize it.

On systems that delegate task of powering up regulators to firmware we
assume that we'll be simply given a dummy regulator.
Signed-off-by: NDudley Du <dudl@cypress.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.

In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.

And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.

To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The GPIOD API can be used from boardcode, so that the DT check can be
removed. To avoid breaking existing boardcode, _optional() variant has been
chosen. For completely removing the DT check, the regulator has also been
made optional, so that it could be supplied from boardcode.

As a side-effect the patch fixes the after-probe reset GPIO state, so that
the device is not kept in reset state.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Using dev_*_drvdata() instead of spi_*_drvdata() reduces lines of code and
prepares the driver for possible tsc2004 support, which is i2c based.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Convert driver so that it uses regmap instead of directly using
spi_transfer for all register accesses.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Replace spaces with tab, so that the tsc2005 Kconfig entry matches the
other entries in drivers/input/touchscreen/Kconfig.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Improve defines for first control byte by removing 0x00 prefix (the defines
are for 8 bit values and not for 16 bit values) and expose register
structure by exposing the shift.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Using managed input device (via devm_input_allocate_device) simplifies
error handling and driver removal paths and also silences CID# 712569.
Reviewed-by: NJoshua Clayton <stillcompiling@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add CYTP0002 to the list of ACPI HIDs recognized by the driver.
Signed-off-by: NDudley Du <dudl@cypress.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Fix the the runtime suspend power management not working issue when system
starts up and before user touches the trackpad device.
TEST=test on Chromebook.
Signed-off-by: NDudley Du <dudl@cypress.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Gen5 and Gen6 trackpad devices are able to detect and report object
proximity data/events, add this function support in the cyapa driver
through the ABS_DISTANCE event.
Signed-off-by: NDudley Du <dudl@cypress.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Based on the cyapa core, add support for basic functionality of the gen6
trackpad devices. The driver can automatically determine what protocol
(gen3, gen5, or gen6) should be used with the attached trackpad device.
Signed-off-by: NDudley Du <dudl@cypress.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Change 'gen5' to 'pip' for all macros, variables and functions that are
shared between gen5 and gen6 modules to make naming more clear and
readable.

Also fix a few spelling errors.
Signed-off-by: NDudley Du <dudl@cypress.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>