提交 7d6548ab 编写于 作者: G Geert Uytterhoeven 提交者: Dmitry Torokhov

Input: Allow compile test of GPIO consumers if !GPIOLIB

The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.

Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
上级 62f46669
......@@ -187,7 +187,7 @@ config KEYBOARD_EP93XX
config KEYBOARD_GPIO
tristate "GPIO Buttons"
depends on GPIOLIB
depends on GPIOLIB || COMPILE_TEST
help
This driver implements support for buttons connected
to GPIO pins of various CPUs (and some other chips).
......@@ -253,7 +253,7 @@ config KEYBOARD_TCA8418
config KEYBOARD_MATRIX
tristate "GPIO driven matrix keypad support"
depends on GPIOLIB
depends on GPIOLIB || COMPILE_TEST
select INPUT_MATRIXKMAP
help
Enable support for GPIO driven matrix keypad.
......
......@@ -259,7 +259,7 @@ config INPUT_APANEL
config INPUT_GP2A
tristate "Sharp GP2AP002A00F I2C Proximity/Opto sensor driver"
depends on I2C
depends on GPIOLIB
depends on GPIOLIB || COMPILE_TEST
help
Say Y here if you have a Sharp GP2AP002A00F proximity/als combo-chip
hooked to an I2C bus.
......@@ -269,7 +269,7 @@ config INPUT_GP2A
config INPUT_GPIO_BEEPER
tristate "Generic GPIO Beeper support"
depends on GPIOLIB
depends on GPIOLIB || COMPILE_TEST
help
Say Y here if you have a beeper connected to a GPIO pin.
......@@ -278,7 +278,7 @@ config INPUT_GPIO_BEEPER
config INPUT_GPIO_TILT_POLLED
tristate "Polled GPIO tilt switch"
depends on GPIOLIB
depends on GPIOLIB || COMPILE_TEST
select INPUT_POLLDEV
help
This driver implements support for tilt switches connected
......@@ -569,7 +569,7 @@ config INPUT_PWM_BEEPER
config INPUT_GPIO_ROTARY_ENCODER
tristate "Rotary encoders connected to GPIO pins"
depends on GPIOLIB
depends on GPIOLIB || COMPILE_TEST
help
Say Y here to add support for rotary encoders connected to GPIO lines.
Check file:Documentation/input/rotary-encoder.txt for more
......@@ -776,7 +776,8 @@ config INPUT_SOC_BUTTON_ARRAY
config INPUT_DRV260X_HAPTICS
tristate "TI DRV260X haptics support"
depends on INPUT && I2C && GPIOLIB
depends on INPUT && I2C
depends on GPIOLIB || COMPILE_TEST
select INPUT_FF_MEMLESS
select REGMAP_I2C
help
......
......@@ -341,7 +341,7 @@ config MOUSE_VSXXXAA
config MOUSE_GPIO
tristate "GPIO mouse"
depends on GPIOLIB
depends on GPIOLIB || COMPILE_TEST
select INPUT_POLLDEV
help
This driver simulates a mouse on GPIO lines of various CPUs (and some
......
......@@ -118,7 +118,7 @@ config TOUCHSCREEN_ATMEL_MXT
config TOUCHSCREEN_AUO_PIXCIR
tristate "AUO in-cell touchscreen using Pixcir ICs"
depends on I2C
depends on GPIOLIB
depends on GPIOLIB || COMPILE_TEST
help
Say Y here if you have a AUO display with in-cell touchscreen
using Pixcir ICs.
......@@ -142,7 +142,7 @@ config TOUCHSCREEN_BU21013
config TOUCHSCREEN_CHIPONE_ICN8318
tristate "chipone icn8318 touchscreen controller"
depends on GPIOLIB
depends on GPIOLIB || COMPILE_TEST
depends on I2C
depends on OF
help
......@@ -156,7 +156,7 @@ config TOUCHSCREEN_CHIPONE_ICN8318
config TOUCHSCREEN_CY8CTMG110
tristate "cy8ctmg110 touchscreen"
depends on I2C
depends on GPIOLIB
depends on GPIOLIB || COMPILE_TEST
help
Say Y here if you have a cy8ctmg110 capacitive touchscreen on
an AAVA device.
......@@ -1030,7 +1030,7 @@ config TOUCHSCREEN_TPS6507X
config TOUCHSCREEN_ZFORCE
tristate "Neonode zForce infrared touchscreens"
depends on I2C
depends on GPIOLIB
depends on GPIOLIB || COMPILE_TEST
help
Say Y here if you have a touchscreen using the zforce
infraread technology from Neonode.
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册