Skip to content

K
Kernel

openeuler / Kernel
接近 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 07 3月, 2016 4 次提交
  3. 05 3月, 2016 2 次提交
  5. 04 3月, 2016 15 次提交
    • L
      net: ezchip: adapt driver to little endian architecture · b54b8c2d
      由 Lada Trimasova 提交于 
      Since ezchip network driver is written with big endian EZChip platform it
is necessary to add support for little endian architecture.

The first issue is that the order of the bits in a bit field is
implementation specific. So all the bit fields are removed.
Named constants are used to access necessary fields.

And the second one is that network byte order is big endian.
For example, data on ethernet is transmitted with most-significant
octet (byte) first. So in case of little endian architecture
it is important to swap data byte order when we read it from
register. In case of unaligned access we can use "get_unaligned_be32"
and in other case we can use function "ioread32_rep" which reads all
data from register and works either with little endian or big endian
architecture.

And then when we are going to write data to register we need to restore
byte order using the function "put_unaligned_be32" in case of
unaligned access and in other case "iowrite32_rep".

The last little fix is a space between type and pointer to observe
coding style.
Signed-off-by: NLada Trimasova <ltrimas@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Tal Zilcer <talz@ezchip.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b54b8c2d
    • S
      sh_eth, ravb: Use ARCH_RENESAS · 274ba628
      由 Simon Horman 提交于 
      Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.

This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      274ba628
    • A
      net: mellanox: add DEVLINK dependencies · 3d1cbe83
      由 Arnd Bergmann 提交于 
      The new NET_DEVLINK infrastructure can be a loadable module, but the drivers
using it might be built-in, which causes link errors like:

drivers/net/built-in.o: In function `mlx4_load_one':
:(.text+0x2fbfda): undefined reference to `devlink_port_register'
:(.text+0x2fc084): undefined reference to `devlink_port_unregister'
drivers/net/built-in.o: In function `mlxsw_sx_port_remove':
:(.text+0x33a03a): undefined reference to `devlink_port_type_clear'
:(.text+0x33a04e): undefined reference to `devlink_port_unregister'

There are multiple ways to avoid this:

a) add 'depends on NET_DEVLINK || !NET_DEVLINK' dependencies
   for each user
b) use 'select NET_DEVLINK' from each driver that uses it
   and hide the symbol in Kconfig.
c) make NET_DEVLINK a 'bool' option so we don't have to
   list it as a dependency, and rely on the APIs to be
   stubbed out when it is disabled
d) use IS_REACHABLE() rather than IS_ENABLED() to check for
   NET_DEVLINK in include/net/devlink.h

This implements a variation of approach a) by adding an
intermediate symbol that drivers can depend on, and changes
the three drivers using it.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 09d4d087 ("mlx4: Implement devlink interface")
Fixes: c4745500 ("mlxsw: Implement devlink interface")
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      3d1cbe83
    • J
      net: relax setup_tc ndo op handle restriction · 5eb4dce3
      由 John Fastabend 提交于 
      I added this check in setup_tc to multiple drivers,

 if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)

Unfortunately restricting to TC_H_ROOT like this breaks the old
instantiation of mqprio to setup a hardware qdisc. This patch
relaxes the test to only check the type to make it equivalent
to the check before I broke it. With this the old instantiation
continues to work.

A good smoke test is to setup mqprio with,

# tc qdisc add dev eth4 root mqprio num_tc 8 \
  map 0 1 2 3 4 5 6 7 \
  queues 0@0 1@1 2@2 3@3 4@4 5@5 6@6 7@7

Fixes: e4c6734e ("net: rework ndo tc op to consume additional qdisc handle paramete")
Reported-by: NSingh Krishneil <krishneil.k.singh@intel.com>
Reported-by: NJake Keller <jacob.e.keller@intel.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      5eb4dce3
    • M
      ath9k: clear bb filter calibration power threshold · 25c0f301
      由 Miaoqing Pan 提交于 
      JP WiFi certification for bandwidth of channel 14 failed, the OBW
is lower than the requirement. Clear the bb filter calibration power
threshold to increase OBW(+2). The fix only for qca9531 chip now.
Signed-off-by: NMiaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      25c0f301
    • A
      ath9k: reduce stack usage in ar9003_aic_cal_post_process · e9a26010
      由 Arnd Bergmann 提交于 
      In some configurations, this function uses more than the warning limit
of 1024 bytes:

drivers/net/wireless/ath/ath9k/ar9003_aic.c: In function 'ar9003_aic_cal_post_process':
drivers/net/wireless/ath/ath9k/ar9003_aic.c:434:1: error: the frame size of 1040 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]

It turns out that there are two large arrays on the stack here, but
almost all the data in them is never used outside of the loop in
which it gets written, so we can replace the array with a single
instance.

The .valid flag is used later, so I'm replacing the array of structures
with an array of bools. An obvious follow-up optimization would be
to replace it with a bitmask and set_bit()/find_first_bit()/
find_last_bit()/... operations. However, I have not tested this patch,
so I sticked to the simpler transformation that does the job of
reducing the stack usage to a harmless level.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      e9a26010
    • M
      ath9k: make NF load complete quickly and reliably · 82def495
      由 Miaoqing Pan 提交于 
      Make NF load complete quickly and reliably. NF load execution
is delayed by HW to end of frame if frame Rx or Tx is ongoing.
Increasing timeout to max frame duration. If NF cal is ongoing
before NF load, stop it before load, and restart it afterwards.
Signed-off-by: NMiaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      82def495
    • M
      ath10k: fix sanity check on enabling btcoex via debugfs · c28e6f06
      由 Mohammed Shafi Shajakhan 提交于 
      First check for the device state before enabling / disabling
btcoex, also return a proper error value. Enabling / disabling
btcoex ideally does a f/w + ath10k_core_restart so the checks
that are applicable for 'simulate_fw_crash' shall be applicable
for this as well
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      c28e6f06
    • A
      ath10k: reduce number of peers to support peer stats feature · af9a6a3a
      由 Anilkumar Kolli 提交于 
      To enable per peer stats feature we are reducing the number of peers.
Firmware has introduced tx stats feature. We have memory limitation in
firmware to add these additional bytes.

These are the new variables introduced in the firmware.
========		=======================
Variable	      	Bytes required/per rate
========		=======================
TX success packets 	1
TX failed packets	1
Retry packets		1
Success bytes		2
TX failed bytes		2
Retry bytes		2
Tx duration		4
Rate			1
Bw and AMPDU flags	1
Total			16 (because of allocation in word pattern)

Firmware sends these tx_stats in pktlog.
If we consider 4 feedbacks at a time, Frimware need about ~1K memory for coding
and 8192 bytes required / per rate [ 4*16*128(peers)].
To accommodate this firmware needs to reduce 10 peers.

This fixes a firmware crash with firmware-5.bin_10.2.4.70.22-2.
Signed-off-by: NAnilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      af9a6a3a
    • R
      ath10k: process htt rx indication as batch mode · da6416ca
      由 Rajkumar Manoharan 提交于 
      On multicore systems, it is possible that txrx tasket can run
in parallel with pci tasklet (i.e smp affinity of ath10k irq is
assigned to multiple CPUs). Feeding and consuming from the same
rx completion list leads to txrx tasklet runs for longer period.
Prevent this by processing a snapshot of rx queue by moving list
into temporary list. Consecutive received frames will be processed
in next batch.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      da6416ca
    • R
      ath10k: reduce rx_lock contention for htt rx indication · e7827e51
      由 Rajkumar Manoharan 提交于 
      Received frame indications are queued into a skb list and latest
processed by txrx tasklet. This skb queue is protected by htt rx lock.
Since the entire rx processing till delivering frame to mac80211 and
replenish tasks are processed under rx_lock protection, there might be
some delay in queuing newly received rx frame into that list on
multicore systems. Optimize this by using skb list lock while accessing
rx completion queue instead of htt rx lock.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      e7827e51
    • A
      ath10k: fix erroneous return value · 22baa980
      由 Anton Protopopov 提交于 
      The ath10k_pci_hif_exchange_bmi_msg() function may return the positive
value EIO instead of -EIO in case of error.
Signed-off-by: NAnton Protopopov <a.s.protopopov@gmail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      22baa980
    • A
      ath10k: add hw_rev to trace events to support pktlog · 18353749
      由 Ashok Raj Nagarajan 提交于 
      pktlog data is different between firmware variants (eg. 10.2 vs 10.4). To
have a unified user space script to decode pktlog trace events generated,
it is desirable to know which firmware variant has provided the events and
thereby decode the pktlogs appropriately. Hardware revision (hw_rev) helps
to determine the firmware variant sending these trace events. So add hw_rev
to trace events.
Signed-off-by: NAshok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      18353749
    • A
      ath10k: fix pktlog in QCA99X0 · 53a5c9bc
      由 Ashok Raj Nagarajan 提交于 
      Currently, we are providing wrong payload data of pktlog to trace points.
Data we receive from FW through copy engine 8 contains pktlog data alone.
We don't need to parse anything in driver before handing it to trace
points.

Fixes: afb0bf7f ("ath10k: add support for pktlog in QCA99X0")
Signed-off-by: NAshok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      53a5c9bc
    • M
      ath10k: fix pointless update of peer stats list · e0b6ce00
      由 Mohammed Shafi Shajakhan 提交于 
      We periodically receive f/w stats event for updating
the rx duration and there is no reason to keep on appending
the f/w stats peer list, as this gets completely cleaned up when
the user polls for f/w stats {pdev, vdev, peer stats}. Only don't
print the warning message in the case PEER_STATS service is enabled

Fixes: 856e7c30 ("ath10k: add debugfs support for Per STA total rx duration")
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      e0b6ce00
  7. 03 3月, 2016 19 次提交