dma-channels, ti,edma-regions and ti,edma-slots no longer needed in DT since
the the same information is available in the IP's CCCFG register.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

dma-channels, ti,edma-regions and ti,edma-slots no longer needed in DT since
the the same information is available in the IP's CCCFG register.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Add device-tree bindings for the ARM CCI-400 on Exynos5420. There
are two slave interfaces: one for the A15 cluster and one for the
A7 cluster.
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

G2D power domain also controls the CMU block of G2D. Since
clock registers can be accessed anytime for viewing
clk_summary, it can cause a system crash if g2d power domain
is disabled.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

MAU powerdomain provides clocks for Audio sub-system block.
This block comprises of the I2S audio controller, audio DMA
blocks and Audio sub-system clock registers.

Right now, there is no way to hook up power-domains with
clock providers.  During late boot when this power-domain
gets disabled, we get following external abort.

Unhandled fault: imprecise external abort (0x1406) at 0x00000000
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Tested-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This change places MDMA1 in disabled node for Exynos5420.
If MDMA1 region is configured with secure mode, it makes
the boot failure with the following on smdk5420 board.
("Unhandled fault: imprecise external abort (0x1406) at 0x00000000")
Thus, arndale-octa board don't need to do the same thing anymore.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Tested-by: NJavi Merino <javi.merino@arm.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Instead of hardcoding the SYSRAM details for each SoC,
pass this information through device tree (DT) and make
the code SoC agnostic. Generic DT SRAM bindings are
used for achieving this.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch includes,
    1] renaming of the HSI2C clocks
    2] renaming of spi clocks according to the datasheet
    3] fixes for child-parent relationships
    4] adding of more clocks related to PERIC block
    5] use GATE_IP_* offsets instead of GATE_BUS_*
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NShaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: NTomasz Figa <t.figa@samsung.com>

Adds the google peach-pit board dts file which uses
exynos5420 SoC.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Adding labels to nodes which do not have it yet in exynos5420.
This is done so as to use reference based node updation in board
files.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Adds the PWM nodes to 5420 pinctrl dtsi file.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch enables the rear facing camera (s5c73m3) on TRATS2 board
by adding the I2C0 bus controller, s5c73m3 sensor, MIPI CSI-2 receiver
and the sensor's voltage regulator supply nodes.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Remove unused /camera/clock-controller node and add required clock
properties to the camera node. This is required for a clock provider
that will be referenced by image sensor devices.
Also add required clock related changes to s5k6a3 device node and
afvdd regulator supply.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The i2c_ak8975 controller uses label i2c8.
This alias is already used for I2C controller 8 defined
in file arch/arm/boot/dts/exynos4.dtsi.

This patch renames a label for i2c_ak8975 to i2c9.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds missing pinctrls for I2C controllers 2-7.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This is another great example of trainwreck engineering:

commit 2646a0e529 (ARM: edma: Add EDMA crossbar event mux support)
added support for using EDMA on peripherals which have no direct EDMA
event mapping.

The code compiles and does not explode in your face, but that's it.

1) Reading an u16 array from an u32 device tree array simply does not
   work. Even if the function is named "edma_of_read_u32_to_s16_array".

   It merily calls of_property_read_u16_array. So the resulting 16bit
   array will have every other entry = 0.

2) The DT entry for the xbar registers related to xbar has length 0x10
   instead of the real length: 0xfd0 - 0xf90 = 0x40.

   Not a real problem as it does not cross a page boundary, but
   wrong nevertheless.

3) But none of this matters as the mapping never happens:

   After reading nonsense edma_of_read_u32_to_s16_array() invalidates
   the first array entry pair, so nobody can ever notice the
   braindamage by immediate explosion.

Seems the QA criteria for this code was solely not to explode when
someone adds edma-xbar-event-map entries to the DT. Goal achieved,
congratulations!

Not really helpful if someone wants to use edma on a device which
requires a xbar mapping.

Fix the issues by:

- annotating the device tree entry with "/bits/ 16" as documented in
  the of_property_read_u16_array kernel doc

- make the size of the xbar register mapping correct

- invalidating the end of the array and not the start

This convoluted mess wants to be completely rewritten as there is no
point to keep the xbar_chan array memory and the iomapping of the xbar
regs around forever. Marking the xbar mapped channels as used should
be done right there.

But that's a different issue and this patch is small enough to make it
work and allows a simple backport for stable.

Cc: stable@vger.kernel.org # v3.12+
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Tegra124 only has 4 UARTs. Parts of the documentation hint at a fifth
UART, but this appears to be left-over from earlier SoC documentation.
Remove the non-existent DT node for UART5.

Cc: <stable@vger.kernel.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Few things were out of order:

- removed ARCH_BCM2835 duplicate
- shuffled ARCH_BCM_5301X, ARCH_U8500 and ARCH_U300 around so to keep the
  list sorted

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-by: NDomenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

s/interrupts-names/interrupt-names/g
s/clocks-names/clock-names/g

Some of the binding files and device tree files get this wrong and the
kernel won't be able to pick it up. Fix them up now so that they don't
get widely used.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by : Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: NGrant Likely <grant.likely@linaro.org>

Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Specify the 'clock-latency' property to avoid certain cpufreq governors
from refusing to work with the following error:
  ondemand governor failed, too long transition latency of HW, fallback to performance governor
Reported-by: NMike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: NMike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

BeagleBoard xM A/B has an inverted usb hub enable line vs the xM C
Signed-off-by: NRobert Nelson <robertcnelson@gmail.com>
[tony@atomide.com: updated for missing bracket]
Signed-off-by: NTony Lindgren <tony@atomide.com>

shiraz.hashim@st.com email-id doesn't exist anymore as he has left the
company.  Replace ST's id with shiraz.linux.kernel@gmail.com.

It also updates .mailmap file to fix address for 'git shortlog'.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

In "ARM: dts: am33xx: correcting dt node unit address for usb", the
usb_ctrl_mod and cppi41dma nodes were updated with the correct register
addresses.  However, the dts files that reference these nodes were not
updated, and those devices are no longer being enabled.

This patch corrects the references for the affected dts files.
Signed-off-by: NLeigh Brown <leigh@solinno.co.uk>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove all remaining uses of gpmc,device-nand that have been added since
the property was removed by commit f40739fa ("ARM: dts: OMAP2+:
Simplify NAND support").
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Wrong documentation in pinmux description can be especially confusing.
Keep it proper.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The correct bit is 24 for AHCLKX.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The USB3 PHY driver (ti-pipe3) was updated so that the relevant
clock phandles are expected in the DT node.
Provide the necessary clocks.
Reported-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The default behaviour of the uart-rx pins on the rk3188 is to be pulled up and
a lot of designs use diodes to even prevent them from being raised from the
outside.

Therefore change the rx-pin settings accordingly.

This also fixes a uart receive problem on mass production Radxa Rock boards.
Signed-off-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Fix typo of renesas,groups in the koeslch dt. The kernel has no
renesas,gpios but this should match renesas,groups.

Noticed thanks to similar fix for Lager by Rob Taylor and Ben Dooks.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.

address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.

address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This adds the clock controller itself, the xti clock on the smdk2416
as well as the clock references in the individual device nodes.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Per bindings of fixed-clock, #clock-cells is a required property.  Let's
add it for those fixed rate clocks.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.

address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

In case the bootloader has incorrectly configured the ALT mode of
MX6SL_PAD_ECSPI1_SS0 pad, we end up with the following probe error:

m25p80 spi0.0: found mr25h256, expected m25p32
m25p80 spi0.0: mr25h256 (32 Kbytes)

In order to avoid this issue, add an entry for MX6SL_PAD_ECSPI1_SS0 pad, so
that kernel configures the ECSPI chip select as GPIO functionality, which
results in correct SPI NOR probe.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The 'remote-endpoint' property should point back to ipu_di1_lvds1
rather than ipu_di0_lvds0.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Since commit (655b43cc staging: imx-drm-core: Use OF graph to find
components and connections between encoder and crtcs), 'crtcs' becomes a
dead property.  Remove it.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Acked-by: NTim Harvey <tharvey@gateworks.com>