Move mt76x02_insert_hdr_pad in m76-core and rename it in
mt76_insert_hdr_pad in order to be used in mt76_dma_tx_queue_skb.
This is a preliminary patch in order to properly support tx dma
mapping for new chipsets (e.g. mt7615)
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Introduce mt76_sw_queue data structure in order to support new
chipsets (e.g. mt7615) that have a shared hardware queue for all traffic
identifiers. mt76_sw_queue will be used to track outstanding packets
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Also update the mask first before calculating the vif index.
Fixes an issue where adding back the same interfaces in a different order
fails because of duplicate vif index use

Fixes: 06662264 ("mt76x02: use mask for vifs")
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Restart the firmware and re-initialize the MAC to be able to recover
from more kinds of hang states
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

When the timer is already running, there is no need to reset the counter,
because the drift will remain the same.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

When mt76x0 and mt76x2 beacon code was unified, it changed the order in which
beacon enable and beacon interval are configured.
Configuring beacon enable before beacon interval can in some cases cause
problems with the beacon timer, leading to clients not waking up properly
from powersave mode.
Fix this by changing the order back to interval first, then enable.

Fixes: cc726268 ("mt76: move mt76x02_bss_info_changed in mt76x02-lib module")
Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

MT_BEACON_TIME_CFG_SYNC_MODE needs to be set for AP mode, according to the
documentation. For other modes it should be irrelevant in this case.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

It needs to be unset instead of set

Fixes: 23405236 ("mt76: fix transmission of encrypted management frames")
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Since we implement beconing on USB now, similar interfaces should be
supported for USB as are for MMIO. Tested only on IBSS mode and
AP mode (not enabled due to lack of PS buffering).
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Configure beaconing on USB devices without PS buffering support.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Disable BEACON timer during init and configure interrupt registers
only for mmio devices.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

BSSID is not strtirct related with beaconing (for example we can have
2 STA vifs) and more related with MAC address, so initaize BSSID when
setting MAC address.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Since we now support mt76x2u feature to allow set mac address
when creating interface in common code we can use it for
mt76x2u.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Use vif_mask to count interfaces to allow to set mac address in HW
if there is only one interface and report error if we create
interface with wrong BSSID resulting in already used index.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Use the appropriate mac80211 callbacks after beacon transmission
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

This will be used by mt7603 as well
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

It will be reused by mt7603 later
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02 led support in mt76x02-lib module in order to
add tpt led trigger to mt76x0e driver
Tested-by: NLGA1150 <dqfext@gmail.com>
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Port mt76x02_check_tx_hang watchdog from vendor driver in order to
perform a device reset when tx mac/dma logic hangs. Tx mac/dma stuck
has been observed when the device is heavy loaded or in a noisy
environment. Moreover introduce wdt delayed work in order to run
tx_hang watchdog. For the moment run mt76x02_check_tx_hang watchdog
just on mt76x2 devices since the issue has not been observed on mt76x0
driver yet
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Configure protection based on information that are provided to
us either by remote AP or by hostapd via HT operation IE.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Use set_rts_threshold calback to enable/disable threshold only for
legacy traffic.

Protection for HT and VHT traffic is defined by HT operation element
and it's provided by remote AP or by hostapd.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Allows adding unassociated stations from mac80211
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>

Open-coding it simplifies the code
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

This allows station removal code to be used by mt7603 later
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

If there are still pending packets in the tx queue when removing a station,
it could possibly lead to a call to further attempts to pull packets from
the mac80211 tx queue after it has already been removed from the scheduling
list.
Prevent this from happening by calling synchronize_rcu after deleting the
wcid pointer before further cleaning up the tx queues.
To be extra careful, ensure that mtxq->list is always initialized properly.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

There is some code in the mac80211 tx status processing code that could
potentially call back into the tx codepath.
To avoid deadlocks, make sure that no tx related spinlocks are taken
during the ieee80211_tx_status call.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Enable VHT tx rates in ad-hoc mode for mt76x0e driver.
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Add mt76x02_config_mac_addr_list routine in order to set
the mac address list supported by the driver. Initialize
wiphy->addresses/n_addresses for mt76x0e driver
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Assure that after we initialize dev->cal.low_gain to -1 this
will cause update gain calibration. Otherwise this might or
might not happen depending on value of second bit of low_gain
and values read from registers in mt76x02_phy_adjust_vga_gain().
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

If we are associated and scanning is performed, sw_scan_complete callback
is done after we get back to operating channel, so we do not perform
queue cal work. Fix this queue cal work from sw_scan_complete().

On mt76x0 we have to restore gain in MT_BBP(AGC, 8) register after
scanning, as it was multiple times modified by channel switch code.
So queue cal work without any delay to set AGC gain value.

Similar like in mt76x2 init AGC gain only when set operating channel
and just check before queuing cal work in sw_scan_complete() if
initialization was already done.

Fixes: bbd10586 ("mt76x0: phy: do not run calibration during channel switch")
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

MT76x2/MT76x0 has somewhat unreliable tx status reporting, and for that
reason the driver currently does not report per-skb tx ack status at all.
This breaks things like client idle polling, which relies on the tx ack
status of a transmitted nullfunc frame.

This patch adds code to report skb-attached tx status if requested by
mac80211 or the rate control module. Since tx status is polled from a
simple FIFO register, the code needs to account for the possibility of
tx status events getting lost.

The code keeps a list of skbs for which tx status is required and passes
them to mac80211 once tx status has been filled in and the DMA queue is
done with it.
If a tx status event is not received after one second, the status rates
are cleared, and a succesful ACK is indicated to avoid spurious disassoc
during assoc or client polling.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Make functions static where possible
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Introduce dfs support in mt76x0e driver and unlock radar channels
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Unify drv_bss_info_changed mac80211 callback and remove duplicated
code in mt76x0 and mt76x2 drivers
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_set_rts_threshold and mt76x02_mac_set_tx_protection
routines in mt76x02-lib module and remove duplicated code in mt76x0
and mt76x2 drivers. Remove pci_mac.c and mt76x0/mac.c since now are
empty files
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_set_tx_ackto and mt76x02_set_coverage_class routines
in mt76x02-lib module in order to be reused by mt76x0 driver.
This is a preliminary patch to unify drv_bss_info_changed mac80211
callback between mt76x0 and mt76x2 drivers
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Add mt76x02_init_beacon_config utility routine in mt76x02-lib
module in order to be reused by mt76x0 driver configuring
BSSID registers and remove duplicated code
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_sta_ps utility routine in mt76x02_util.c
in order to be reused by mt76x0 driver adding AP support
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_get_txpower utility routine in mt76x02-lib module
in order to be reused by mt76x0 and mt76x2u drivers
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_sw_scan and mt76x02_sw_scan_complete utility routines
in mt76x02_util.c in order to be reused by mt76x0 and mt76x2u drivers
and remove duplicated code
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>