Without this check rebuild vsi can lead to kernel panic.
Signed-off-by: NMichal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Save state to correct recovery memory and I/O BARs address
after PCI bus reset. Without this after reset kernel can't
read device registers.
Signed-off-by: NMichal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As part of the driver unload flow, a PF reset is issued which may still
cause an interrupt to be generated by the device.  Do not clear the
interrupt scheme until the reset is complete and there are no pending
transactions otherwise a hardware error may occur.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

At this point ice driver is able to work on order 1 pages that are split
onto two 3k buffers. Let's reflect that when user is setting new MTU
size and XDP is present on interface.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add zero copy AF_XDP support.  This patch adds zero copy support for
Tx and Rx; code for zero copy is added to ice_xsk.h and ice_xsk.c.

For Tx, implement ndo_xsk_wakeup. As with other drivers, reuse
existing XDP Tx queues for this task, since XDP_REDIRECT guarantees
mutual exclusion between different NAPI contexts based on CPU ID. In
turn, a netdev can XDP_REDIRECT to another netdev with a different
NAPI context, since the operation is bound to a specific core and each
core has its own hardware ring.

For Rx, allocate frames as MEM_TYPE_ZERO_COPY on queues that AF_XDP is
enabled.
Signed-off-by: NKrzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Co-developed-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for XDP. Implement ndo_bpf and ndo_xdp_xmit.  Upon load of
an XDP program, allocate additional Tx rings for dedicated XDP use.
The following actions are supported: XDP_TX, XDP_DROP, XDP_REDIRECT,
XDP_PASS, and XDP_ABORTED.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove a few uses of kernel configuration flags from ice_lib.c by
introducing a new source file ice_base.c. Also move corresponding
function prototypes from ice_lib.h to ice_base.h and include ice_base.h
where required.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump version to 0.8.1-k
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Attempt to request an optional device-specific DDP package file
(one with the PCIe Device Serial Number in its name so that different DDP
package files can be used on different devices). If the optional package
file exists, download it to the device. If not, download the default
package file.

Log an appropriate message based on whether or not a DDP package
file exists and the return code from the attempt to download it to the
device.  If the download fails and there is not already a package file on
the device, go into "Safe Mode" where some features are not supported.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The FW build id is currently being displayed as an int which doesn't make
sense. Instead display FW build id as a hex value. Also add other useful
information to the output such as NVM version, API patch info, and FW
build hash.
Signed-off-by: NLukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver is required to send a version to the firmware
to indicate that the driver is up. If the driver doesn't
do this the firmware doesn't behave properly.
Signed-off-by: NPaul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove q_left_tx and q_left_rx from the PF struct as these can be
obtained by calling ice_get_avail_txq_count and ice_get_avail_rxq_count
respectively.

The function ice_determine_q_usage is only setting num_lan_tx and
num_lan_rx in the PF structure, and these are later assigned to
vsi->alloc_txq and vsi->alloc_rxq respectively. This is an unnecessary
indirection, so remove ice_determine_q_usage and just assign values
for vsi->alloc_txq and vsi->alloc_rxq in ice_vsi_set_num_qs and use
these to set num_lan_tx and num_lan_rx respectively.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add an additional boolean parameter to the ice_init_dcb
function.  This boolean controls if the LLDP MIB change
events are registered for.  Also, add a new function
defined ice_cfg_lldp_mib_change.  The additional function
is necessary to be able to register for LLDP MIB change
events after calling ice_init_dcb.  The net effect of these
two changes is to allow a delayed registration for MIB change
events so that the driver is not accepting events before it
is ready for them.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Check the ICE_FLAG_DCB_CAPABLE before calling ice_init_pf_dcb.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are multiple places where we currently use ice_find_vsi_by_type
to get the PF (a.k.a. main) VSI. The PF VSI by definition is always
the first element in the pf->vsi array (i.e. pf->vsi[0]). So instead
add and use a new helper function ice_get_main_vsi, which just returns
pf->vsi[0].
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is currently a check in get_ndo_stats that
returns before updating stats if the VSI is down
or there are no Tx or Rx queues.  This causes the
netdev to report zero stats with the netdev is down.

Remove the check so that the behavior of reporting
stats is the same as it was in IXGBE.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver needs to inform the user if there is an issue
with the topology / configuration of the link.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Print the state of auto-negotiation when printing the Link
up message.  Adds new text to the "NIC Link is up" line like
Autoneg: <True | False>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

According to the specification, a PF Reset must be done as part of the
driver unload flow.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ice_reset_subtask needs to handle EMP resets as well, as EMP resets
can be triggered by the firmware. This patch adds the logic to do
this.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The order of operations was incorrect in ice_remove(). The code would
try to use adminq operations after the adminq was disabled. This caused
all adminq calls to fail and possibly timeout waiting.
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current implementation of ice_ena_msix_range is difficult to read
and has subtle issues. This patch reworks the said function for
clarity and correctness.

More specifically,

1. Add more checks to bail out of 'needed' is greater than 'v_left'.

2. Simplify fallback logic

3. Do not set pf->num_avail_sw_msix in ice_ena_msix_range as it
   gets overwritten by ice_init_interrupt_scheme.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The total number of queues available on the device is divided between
multiple physical functions (PF) in the firmware and provided to the
driver when it gets function capabilities from the firmware. Thus
each PF knows how many Tx/Rx queues it has. These queues are then
doled out to different VSIs (for LAN traffic, SR-IOV VF traffic, etc.)

To track usage of these queues at the PF level, the driver uses two
bitmaps avail_txqs and avail_rxqs. At the VSI level (i.e. struct ice_vsi
instances) the driver uses two arrays txq_map and rxq_map, to track
ownership of VSIs' queues in avail_txqs and avail_rxqs respectively.

The aforementioned bitmaps and arrays should be allocated dynamically,
because the number of queues supported by a PF is only available once
function capabilities have been queried. The current static allocation
consumes way more memory than required.

This patch removes the DECLARE_BITMAP for avail_txqs and avail_rxqs
and instead uses bitmap_zalloc to allocate the bitmaps during init.
Similarly txq_map and rxq_map are now allocated in ice_vsi_alloc_arrays.
As a result ICE_MAX_TXQS and ICE_MAX_RXQS defines are no longer needed.
Also as txq_map and rxq_map are now allocated and freed, some code
reordering was required in ice_vsi_rebuild for correct functioning.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The VF driver can call VIRTCHNL_OP_[ENABLE|DISABLE]_QUEUES separately
for each queue. Add support for virtchnl_queue_select.[tx|rx]_queues
bitmap which is used to indicate which queues to enable and disable.

Add tracing of VF Tx/Rx per queue enable state to avoid enabling enabled
queues and disabling disabled queues. Add total queues enabled count and
clear ICE_VF_STATE_QS_ENA when count is zero.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: NPeng Huang <peng.huang@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The loop counter of a for-loop is a u8 however this is being compared
to an int upper bound and this can lead to an infinite loop if the
upper bound is greater than 255 since the loop counter will wrap back
to zero. Fix this potential issue by making the loop counter an int.

Addresses-Coverity: ("Infinite loop")
Fixes: c7aeb4d1 ("ice: Disable VFs until reset is completed")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In case of MDD events on VF, don't clog kernel log with unlimited VF MDD
events message "VF 0 has had 1018 MDD events since last boot" - limit
events log message to 30, based on the observation in some experimentation
with sending malicious packet once, and number of events reported before
device stopped observing MDD events.

Also removed defunct macro "ICE_DFLT_NUM_MDD_EVENTS_ALLOWED" for tracking
number of MDD events allowed before disabling the interface...
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a VSI is accessed inside the ice_for_each_vsi macro in the rebuild
path (ice_vsi_rebuild_all() and ice_vsi_replay_all()), it is referred to
as pf->vsi[i]. Introduce local variables to improve readability.
Signed-off-by: NKrzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

1. ndo_open and ndo_stop are implemented by ice_open and ice_stop
   respectively. When enabling/disabling VSIs, just call
   ice_open/ice_stop instead of ndo_open/ndo_stop.

2. Rework logic around rtnl_lock/rtnl_unlock

3. In ice_ena_vsi, remove an unnecessary stack variable and return
   0 instead of err when __ICE_NEEDS_RESTART is not set.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the issue where port and PFC statistics counters are
incrementing at the wrong port with 4x25G cards.
Read the GLPRT port registers using lport parameter instead of pf_id to
update the statistics otherwise the pf_ids are flipped for ports 2 and 3
when read from the HW register PF_FUNC_RID and this is expected as per
hardware specification.
Signed-off-by: NUsha Ketineni <usha.k.ketineni@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

VSI, especially VF could request to add or remove filter for another VSI,
driver should really guide such request and disallow it.
However, instead of returning error for such malicious request, driver
can simply return success.

In addition, we are not tracking number of MAC filters configured per
VF correctly - and this leads to issue updating VF MAC filters whenever
they were removed and re-configured via bringing VF interface down and
up. Also, since VF could send request to update multiple MAC filters at
once, driver should program those filters individually in the switch, in
order to determine which action resulted to error, and communicate
accordingly to the VF.

So, with this changes, we now track number of filters added right from
when VF resources allocation is done, and could properly add filters for
both trusted and non_trusted VFs, without MAC filters mis-match issue in
the switch...

Also refactor code, so that driver can use new function to add or remove
MAC filters.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Users expect ethtool statistics to be updated on-demand when invoking
'ethtool -S <iface>' instead of providing a snapshot of statistics taken
once a second (the frequency of the watchdog task where stats are currently
updated).  Update stats every time 'ethtool -S <iface>' is run.

Also, fix an indentation style issue and an unnecessary local variable
initialization in ice_get_ethtool_stats() discovered while investigating
the subject issue.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we use the ICE_MBXQ_LEN for both the Mailbox send and receive
queues that are used to communicate with VFs. This is fine for the send
queue because the PF driver will lock the queue for every single send,
but for the Mailbox receive queue every VF is posting to its Mailbox
send queue and the hardware is then handing the message to the PF on its
Mailbox receive queue. This becomes a problem with many VFs because it
seems to overburden the Mailbox receive queue on the PF. Fix this by
increasing the Mailbox receive queue for the PF to 512 entries.

The number 512 was determined based on the number of VFs supported by
the device. We can have a total of 256 VFs so in the worst case this
allows the VFs to put 2 messages in the PFs Mailbox receive queue at the
same time.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During rebuild ice_ena_vsi() is called to recover the VSI state.
This function assumes the PF VSI is always to be enabled, however,
it's possible that during reset/rebuild the interface can be
brought down.  If this occurs, we can attempt to bring up the PF
VSI on a downed interface which can lead to various crashes. If
the interface is not running, do not bring up the associated VSI.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently in ice_get_tx_pending we try to read a Tx ring's tail. This is
then compared with the software based head (next_to_clean) to determine
if we have pending work. This will never work because reading of the Tx
ring's tail is no longer supported. Fix this by using the software based
tail (next_to_use) to determine if there is pending work.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update driver version to 0.7.5
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This flag is not needed and is called every time we re-enable interrupts
in the hotpath so remove it. Also remove ice_vsi_req_irq() because it
was a wrapper function for ice_vsi_req_irq_msix() whose sole purpose was
checking the ICE_FLAG_MSIX_ENA flag.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we are not reporting dropped counts at the port level to
ethtool or netlink. This was found when debugging Rx dropped issues
and the total packets sent did not equal the total packets received
minus the rx_dropped, which was very confusing. To determine dropped
counts at the port level we need to read the PRTRPB_RDPC register.
To fix reporting we will store the dropped counts in the PF's
rx_discards. This will be reported to netlink by storing it in the
PF VSI's rx_missed_errors signaling that the receiver missed the
packet. Also, we will report this to ethtool in the rx_dropped.nic
field.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds code to clear VFs enable status until reset is completed,
and Tx/Rx rings are setup. Without this patch, the code flow request Tx
queues to be disabled after reset, especially PFR - where VF VSI Tx rings
have already been wiped off in the NVM and result to adminq error based on
the call to disable Tx LAN queue in ice_reset_all_vfs function call.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The firmware reports an error when trying to configure a port with no
media. Instead of always configuring the port, check for media before
attempting to configure it. In the absence of media, turn off link and
poll for media to become available before re-enabling link.

Move ice_force_phys_link_state() up to avoid forward declaration.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, ice_stat_update32 and ice_stat_update40 will limit the
value of the software statistic to 32 or 40 bits wide, depending on
which register is being read.

This means that if a driver is running for a long time, the displayed
software register values will roll over to zero at 40 bits or 32 bits.

This occurs because the functions directly assign the difference between
the previous value and current value of the hardware statistic.

Instead, add this value to the current software statistic, and then
update the previous value.

In this way, each time ice_stat_update40 or ice_stat_update32 are
called, they will increment the software tracking value by the
difference of the hardware register from its last read. The software
tracking value will correctly count up until it overflows a u64.

The only requirement is that the ice_stat_update functions be called at
least once each time the hardware register overflows.

While we're fixing ice_stat_update40, modify it to use rd64 instead of
two calls to rd32. Additionally, drop the now unnecessary hireg
function parameter.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>