The VF_MBX_ARQLEN register array is per-PF, not global, so we should not
use the absolute VF ID as an index. Instead, use the per-PF VF ID.

This fixes an issue with VFs on PFs other than 0 not seeing reset.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Without this check rebuild vsi can lead to kernel panic.
Signed-off-by: NMichal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Save state to correct recovery memory and I/O BARs address
after PCI bus reset. Without this after reset kernel can't
read device registers.
Signed-off-by: NMichal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Adjust ice_init_dcb to set the is_sw_lldp boolean
in the case where the FW has been detected to be
in an untenable state such that the driver
should forcibly make sure it is off.

This will ensure that the FW is in a known state.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As part of the driver unload flow, a PF reset is issued which may still
cause an interrupt to be generated by the device.  Do not clear the
interrupt scheme until the reset is complete and there are no pending
transactions otherwise a hardware error may occur.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If DCBx request non-contiguous TCs, then the driver will configure default
traffic class (TC0). This is done to prevent Tx hang since the driver
currently does not support non-contiguous TC.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The Boot Configuration Section Block has been moved to the Preserved Field
Area (PFA) of NVM. Update the NVM reads that involves Boot Configuration
Section.
Signed-off-by: NMd Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement ethtool -m support to read eeprom data from SFP/QSFP modules.
Signed-off-by: NScott W Taylor <scott.w.taylor@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

At this point ice driver is able to work on order 1 pages that are split
onto two 3k buffers. Let's reflect that when user is setting new MTU
size and XDP is present on interface.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Driver is now prepared for building the skb around the existing Rx
buffer, so introduce the ice_build_skb responsible for it. Make use of
XDP's data_meta as well.

I've observed around 30% less CPU consumption with build_skb Rx path, in
comparison to legacy Rx. What stands behind such result is the avoidance
of flow_dissector (which we were diving into via eth_get_headlen) and no
memcpy calls.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Take into account the underlying architecture specific settings and
based on that calculate the possible padding that can be supplied.
Typically, for x86 and standard MTU size we will end up with 192 bytes
of headroom. This is the same behavior as our other drivers have and we
can dedicate it for XDP purposes.

Furthermore, introduce the Rx ring flag for indicating whether build_skb
is used on particular. Based on that invoke the routines for padding
calculation.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add an ethtool "legacy-rx" priv flag for toggling the Rx path. This
control knob will be mainly used for build_skb usage as well as buffer
size/MTU manipulation.

In preparation for adding build_skb support in a way that it takes
care of how we set the values of max_frame and rx_buf_len fields of
struct ice_vsi. Specifically, in this patch mentioned fields are set to
values that will allow us to provide headroom and tailroom in-place.

This can be mostly broken down onto following:
- for legacy-rx "on" ethtool control knob, old behaviour is kept;
- for standard 1500 MTU size configure the buffer of size 1536, as
  network stack is expecting the NET_SKB_PAD to be provided and
  NET_IP_ALIGN can have a non-zero value (these can be typically equal
  to 32 and 2, respectively);
- for larger MTUs go with max_frame set to 9k and configure the 3k
  buffer in case when PAGE_SIZE of underlying arch is less than 8k; 3k
  buffer is implying the need for order 1 page, so that our page
  recycling scheme can still be applied;

With that said, substitute the hardcoded ICE_RXBUF_2048 and PAGE_SIZE
values in DMA API that we're making use of with rx_ring->rx_buf_len and
ice_rx_pg_size(rx_ring). The latter is an introduced helper for
determining the page size based on its order (which was figured out via
ice_rx_pg_order). Last but not least, take care of truesize calculation.

In the followup patch the headroom/tailroom computation logic will be
introduced.

This change aligns the buffer and frame configuration with other Intel
drivers, most importantly with iavf.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add zero copy AF_XDP support.  This patch adds zero copy support for
Tx and Rx; code for zero copy is added to ice_xsk.h and ice_xsk.c.

For Tx, implement ndo_xsk_wakeup. As with other drivers, reuse
existing XDP Tx queues for this task, since XDP_REDIRECT guarantees
mutual exclusion between different NAPI contexts based on CPU ID. In
turn, a netdev can XDP_REDIRECT to another netdev with a different
NAPI context, since the operation is bound to a specific core and each
core has its own hardware ring.

For Rx, allocate frames as MEM_TYPE_ZERO_COPY on queues that AF_XDP is
enabled.
Signed-off-by: NKrzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Co-developed-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In preparation of AF XDP, move functions that will be used both by skb and
zero-copy paths to a new file called ice_txrx_lib.c.  This allows us to
avoid using ifdefs to control the staticness of said functions.

Move other functions (ice_rx_csum, ice_rx_hash and ice_ptype_to_htype)
called only by the moved ones to the new file as well.
Signed-off-by: NKrzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for XDP. Implement ndo_bpf and ndo_xdp_xmit.  Upon load of
an XDP program, allocate additional Tx rings for dedicated XDP use.
The following actions are supported: XDP_TX, XDP_DROP, XDP_REDIRECT,
XDP_PASS, and XDP_ABORTED.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There's no reason for treating DCB as first class citizen when configuring
the Tx queues and going through TCs. Reverse the logic and base the
configuration logic on rings, which is the object of interest anyway.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove a few uses of kernel configuration flags from ice_lib.c by
introducing a new source file ice_base.c. Also move corresponding
function prototypes from ice_lib.h to ice_base.h and include ice_base.h
where required.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump version to 0.8.1-k
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Attempt to request an optional device-specific DDP package file
(one with the PCIe Device Serial Number in its name so that different DDP
package files can be used on different devices). If the optional package
file exists, download it to the device. If not, download the default
package file.

Log an appropriate message based on whether or not a DDP package
file exists and the return code from the attempt to download it to the
device.  If the download fails and there is not already a package file on
the device, go into "Safe Mode" where some features are not supported.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add functions to initialize, parse, and clean structures representing
the DDP package.

Upon completion of package download, read and store the DDP package
contents to these structures.  This configuration is used to
identify the default behavior and later used to update the HW table
entries.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the required defines, structures, and functions to enable downloading
a DDP package.  Before download, checks are performed to ensure the package
is valid and compatible.

Note that package download is not yet requested by the driver as further
initialization is required to utilize the package.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The FW build id is currently being displayed as an int which doesn't make
sense. Instead display FW build id as a hex value. Also add other useful
information to the output such as NVM version, API patch info, and FW
build hash.
Signed-off-by: NLukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver is required to send a version to the firmware
to indicate that the driver is up. If the driver doesn't
do this the firmware doesn't behave properly.
Signed-off-by: NPaul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ice_parse_caps is printing capabilities in a different way when
compared to the variable names. This makes it difficult to search for
the right strings in the debug logs. So this patch updates the
print strings to be exactly the same as the fields' name in the
structure.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver should start out with a reasonable number of descriptors that
can prevent drops due to a CPU being in a power management state.
Change the default number of descriptors to 2048.
The user can always change the value at runtime.  Transmit descriptor
counts are not modified because they don't need to change due to the
speed of the interface, or for power managed CPUs, but the code is
simplified to a fixed value for the transmit default.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove q_left_tx and q_left_rx from the PF struct as these can be
obtained by calling ice_get_avail_txq_count and ice_get_avail_rxq_count
respectively.

The function ice_determine_q_usage is only setting num_lan_tx and
num_lan_rx in the PF structure, and these are later assigned to
vsi->alloc_txq and vsi->alloc_rxq respectively. This is an unnecessary
indirection, so remove ice_determine_q_usage and just assign values
for vsi->alloc_txq and vsi->alloc_rxq in ice_vsi_set_num_qs and use
these to set num_lan_tx and num_lan_rx respectively.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add an additional boolean parameter to the ice_init_dcb
function.  This boolean controls if the LLDP MIB change
events are registered for.  Also, add a new function
defined ice_cfg_lldp_mib_change.  The additional function
is necessary to be able to register for LLDP MIB change
events after calling ice_init_dcb.  The net effect of these
two changes is to allow a delayed registration for MIB change
events so that the driver is not accepting events before it
is ready for them.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add internal usage flag, bit 91 as described in spec.
Update width of internal queue state to 122 also as described in spec.
Signed-off-by: NAshish Shah <ashish.n.shah@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes how and when the driver report link status, instead of
waiting till the call to enable queues for VF, we should report link
status earlier with opcode to get VF resources - So as to avoid reporting
erroneous information, especially when queues have not been configured.
In addition, we can also make a call to get and report link status change
after when queue is enabled, at least to report netdev or PHY link status.
This is in accordance to how link speed is being reported for PF...
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Check the ICE_FLAG_DCB_CAPABLE before calling ice_init_pf_dcb.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is port of a fix from i40e commit 2ad1274f ("i40e: don't
report link up for a VF who hasn't enabled queues")

Older VF drivers do not respond well to receiving a link
up notification before queues are enabled. This can cause their state
machine to think that it is safe to send traffic. This results in a Tx
hang on the VF.

Record whether the PF has actually enabled queues for the VF. When
reporting link status, always report link down if the queues aren't
enabled. In this way, the VF driver will never receive a link up
notification until after its queues are enabled.
Signed-off-by: NLukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a PFR (or bigger reset) occurs, the device clears the VF_MBX_ARQLEN
register for all VFs. But if a VFR is triggered by a VF, the device does
NOT clear this register, and the VF driver will never see the reset.

When this happens, the VF driver will eventually timeout and attempt
recovery, and usually it will be successful. But this makes resets take
a long time and there are occasional failures.

We cannot just blithely clear this register on every reset; this has
been shown to cause synchronization problems when a PFR is triggered
with a large number of VFs.

Fix this by clearing VF_MBX_ARQLEN when the reset source is not PFR.
GlobR will trigger PFR, so this test catches that occurrence as well.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver has supported a transmit work limit
that was configurable from ethtool for a long time, but
there are no good use cases for having it be a variable
that can be changed at run time.  In addition, this
variable was noted to be causing performance overhead
due to cache misses.

Just remove the variable and let the code use a constant
so that the functionality is maintained (a limit on the
number of transmits that will be cleaned in any one call
to the clean routines) without the cache miss.

Removes code, removes a variable, removes testing surface. Yay.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a small bit of efficiency to the code by adding a
prefetch of the port_info structure in order to help
avoid a cache miss a little later on in execution.

Also add an unlikely statement to a branch which
generally will never happen in normal operation.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is a simple patch to move the assignment to a local variable
closer to the site where the local variable is used.  This
can help readability and also maybe performance, although the
performance enhancement is really dependent upon the compiler.

No functional change.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are a couple of functions that don't need two arguments
passed in when the second argument already had access to
the pointer pointed to by the first.

Remove the unnecessary arguments.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ice_sched_get_tc_node uses pi->root without checking for NULL. Add a
check to prevent NULL pointer dereference.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are multiple places where we currently use ice_find_vsi_by_type
to get the PF (a.k.a. main) VSI. The PF VSI by definition is always
the first element in the pf->vsi array (i.e. pf->vsi[0]). So instead
add and use a new helper function ice_get_main_vsi, which just returns
pf->vsi[0].
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently when vsi->req_txqs or vsi->req_rxqs are set we don't
correctly set the number of vsi->num_q_vectors. Fix this by
setting the number of queue vectors based on the max
between the vsi->alloc_txqs and vsi->alloc_rxqs.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently if the VF adds a VLAN, VLAN pruning will be enabled for that VSI.
Also, when a VLAN gets deleted it will disable VLAN pruning even if other
VLAN(s) exists for the VF. Fix this by only disabling VLAN pruning on the
VF VSI when removing the last VF (i.e. vf->num_vlan == 0).
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>