The VF_MBX_ARQLEN register array is per-PF, not global, so we should not
use the absolute VF ID as an index. Instead, use the per-PF VF ID.

This fixes an issue with VFs on PFs other than 0 not seeing reset.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Without this check rebuild vsi can lead to kernel panic.
Signed-off-by: NMichal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Save state to correct recovery memory and I/O BARs address
after PCI bus reset. Without this after reset kernel can't
read device registers.
Signed-off-by: NMichal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Adjust ice_init_dcb to set the is_sw_lldp boolean
in the case where the FW has been detected to be
in an untenable state such that the driver
should forcibly make sure it is off.

This will ensure that the FW is in a known state.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As part of the driver unload flow, a PF reset is issued which may still
cause an interrupt to be generated by the device.  Do not clear the
interrupt scheme until the reset is complete and there are no pending
transactions otherwise a hardware error may occur.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If DCBx request non-contiguous TCs, then the driver will configure default
traffic class (TC0). This is done to prevent Tx hang since the driver
currently does not support non-contiguous TC.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The Boot Configuration Section Block has been moved to the Preserved Field
Area (PFA) of NVM. Update the NVM reads that involves Boot Configuration
Section.
Signed-off-by: NMd Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement ethtool -m support to read eeprom data from SFP/QSFP modules.
Signed-off-by: NScott W Taylor <scott.w.taylor@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement the VF stats gathering via the kernel via ndo_get_vf_stats().
The driver will show per-VF stats in the output of the command:
ip -s link show dev <PF>

Testing Hints:
ip -s link show dev eth0
will return non-zero VF stats.
...
   vf 0 MAC 00:55:aa:00:55:aa, spoof checking on, link-state enable, trust off
   RX: bytes  packets  mcast   bcast
   128000     1000     104     104
   TX: bytes  packets
   128000     1000
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The I40E_DEV_ID_10G_BASE_T_BC device id was added previously,
but was not enabled in all the appropriate places.  Adding it
to enable it's use.
Signed-off-by: NAlice Michael <alice.michael@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

HW timestamping can only be requested for a packet if the NIC is first
setup via ioctl(SIOCSHWTSTAMP). If this step was skipped, then the ixgbe
driver still allowed TX packets to request HW timestamping. In this
situation, we see 'clearing Tx Timestamp hang' noise in the log.

Fix this by checking that the NIC is configured for HW TX timestamping
before accepting a HW TX timestamping request.

Similar-to:
   commit 26bd4e2d ("igb: protect TX timestamping from API misuse")
   commit 0a6f2f05 ("igb: Fix a test with HWTSTAMP_TX_ON")
Signed-off-by: NManjunath Patil <manjunath.b.patil@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

An upcoming out-of-tree release will be occurring which will include the
recent functionality to support virtual function statistics. Update the
kernel driver version to match this.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to address locality issues present in the ixgbe driver
when it is loaded on a system supporting multiple NUMA nodes and more CPUs
then the device can map in a 1:1 fashion. Instead of just arbitrarily
mapping itself to CPUs 0-62 it would make much more sense to map itself to
the local CPUs first, and then map itself to any remaining CPUs that might
be used.

The first effect of this is that queue 0 should always be allocated on the
local CPU/NUMA node. This is important as it is the default destination if
a packet doesn't match any existing flow director filter or RSS rule and as
such having it local should help to reduce QPI cross-talk in the event of
an unrecognized traffic type.

In addition this should increase the likelihood of the RSS queues being
allocated and used on CPUs local to the device while the ATR/Flow Director
queues would be able to route traffic directly to the CPU that is likely to
be processing it.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Support capturing and reporting statistics for all of the VFs associated
with a given PF device via the ndo_get_vf_stats callback.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the missing field initializers for a couple of the TLV attribute
macros. This resolves the last few -Wmissing-field-initializers warnings
for the fm10k Linux driver.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

At this point ice driver is able to work on order 1 pages that are split
onto two 3k buffers. Let's reflect that when user is setting new MTU
size and XDP is present on interface.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Driver is now prepared for building the skb around the existing Rx
buffer, so introduce the ice_build_skb responsible for it. Make use of
XDP's data_meta as well.

I've observed around 30% less CPU consumption with build_skb Rx path, in
comparison to legacy Rx. What stands behind such result is the avoidance
of flow_dissector (which we were diving into via eth_get_headlen) and no
memcpy calls.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Take into account the underlying architecture specific settings and
based on that calculate the possible padding that can be supplied.
Typically, for x86 and standard MTU size we will end up with 192 bytes
of headroom. This is the same behavior as our other drivers have and we
can dedicate it for XDP purposes.

Furthermore, introduce the Rx ring flag for indicating whether build_skb
is used on particular. Based on that invoke the routines for padding
calculation.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add an ethtool "legacy-rx" priv flag for toggling the Rx path. This
control knob will be mainly used for build_skb usage as well as buffer
size/MTU manipulation.

In preparation for adding build_skb support in a way that it takes
care of how we set the values of max_frame and rx_buf_len fields of
struct ice_vsi. Specifically, in this patch mentioned fields are set to
values that will allow us to provide headroom and tailroom in-place.

This can be mostly broken down onto following:
- for legacy-rx "on" ethtool control knob, old behaviour is kept;
- for standard 1500 MTU size configure the buffer of size 1536, as
  network stack is expecting the NET_SKB_PAD to be provided and
  NET_IP_ALIGN can have a non-zero value (these can be typically equal
  to 32 and 2, respectively);
- for larger MTUs go with max_frame set to 9k and configure the 3k
  buffer in case when PAGE_SIZE of underlying arch is less than 8k; 3k
  buffer is implying the need for order 1 page, so that our page
  recycling scheme can still be applied;

With that said, substitute the hardcoded ICE_RXBUF_2048 and PAGE_SIZE
values in DMA API that we're making use of with rx_ring->rx_buf_len and
ice_rx_pg_size(rx_ring). The latter is an introduced helper for
determining the page size based on its order (which was figured out via
ice_rx_pg_order). Last but not least, take care of truesize calculation.

In the followup patch the headroom/tailroom computation logic will be
introduced.

This change aligns the buffer and frame configuration with other Intel
drivers, most importantly with iavf.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add zero copy AF_XDP support.  This patch adds zero copy support for
Tx and Rx; code for zero copy is added to ice_xsk.h and ice_xsk.c.

For Tx, implement ndo_xsk_wakeup. As with other drivers, reuse
existing XDP Tx queues for this task, since XDP_REDIRECT guarantees
mutual exclusion between different NAPI contexts based on CPU ID. In
turn, a netdev can XDP_REDIRECT to another netdev with a different
NAPI context, since the operation is bound to a specific core and each
core has its own hardware ring.

For Rx, allocate frames as MEM_TYPE_ZERO_COPY on queues that AF_XDP is
enabled.
Signed-off-by: NKrzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Co-developed-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In preparation of AF XDP, move functions that will be used both by skb and
zero-copy paths to a new file called ice_txrx_lib.c.  This allows us to
avoid using ifdefs to control the staticness of said functions.

Move other functions (ice_rx_csum, ice_rx_hash and ice_ptype_to_htype)
called only by the moved ones to the new file as well.
Signed-off-by: NKrzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for XDP. Implement ndo_bpf and ndo_xdp_xmit.  Upon load of
an XDP program, allocate additional Tx rings for dedicated XDP use.
The following actions are supported: XDP_TX, XDP_DROP, XDP_REDIRECT,
XDP_PASS, and XDP_ABORTED.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There's no reason for treating DCB as first class citizen when configuring
the Tx queues and going through TCs. Reverse the logic and base the
configuration logic on rings, which is the object of interest anyway.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove a few uses of kernel configuration flags from ice_lib.c by
introducing a new source file ice_base.c. Also move corresponding
function prototypes from ice_lib.h to ice_base.h and include ice_base.h
where required.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

__IXGBE_RX_BUILD_SKB_ENABLED bit is already cleared.
Signed-off-by: NIgor Pylypiv <igor.pylypiv@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In e1000_set_ringparam(), 'tx_old' and 'rx_old' are not deallocated if
e1000_up() fails, leading to memory leaks. Refactor the code to fix this
issue.
Signed-off-by: NWenwen Wang <wenwen@cs.uga.edu>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Magnus's fix to resolve a potential receive buffer starvation for AF_XDP
got applied to both the i40e_xsk_umem_enable/disable() functions, when it
should have only been applied to the "enable".  So clean up the undesired
code in the disable function.

CC: Magnus Karlsson <magnus.karlsson@intel.com>
Fixes: 1f459bdc ("i40e: fix potential RX buffer starvation for AF_XDP")
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>

At least on the i350 there is an annoying behavior that is maybe also
present on 82580 devices, but was probably not noticed yet as MAS is not
widely used.

If no cable is connected on both fiber/copper ports the media auto sense
code will constantly swap between them as part of the watchdog task and
produce many unnecessary kernel log messages.

The swap code responsible for this behavior (switching to fiber) should
not be executed if the current media type is copper and there is no signal
detected on the fiber port. In this case we can safely wait until the
AUTOSENSE_EN bit is cleared.
Signed-off-by: NManfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables the hardware feature "Media Auto Sense" also on the
i350. It works in the same way as on the 82850 devices. Hardware designs
using dual PHYs (fiber/copper) can enable this feature by setting the MAS
enable bits in the NVM_COMPAT register (0x03) in the EEPROM.
Signed-off-by: NManfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fatal read errors are worth warning about, unless of course the device
was just unplugged from the machine - something that's a rather normal
occurrence when the igb/igc adapter is located on a Thunderbolt dock. So,
let's only WARN() if there's a fatal read error while the device is
still present.

This fixes the following WARN splat that's been appearing whenever I
unplug my Caldigit TS3 Thunderbolt dock from my laptop:

  igb 0000:09:00.0 enp9s0: PCIe link lost
  ------------[ cut here ]------------
  igb: Failed to read reg 0x18!
  WARNING: CPU: 7 PID: 516 at
  drivers/net/ethernet/intel/igb/igb_main.c:756 igb_rd32+0x57/0x6a [igb]
  Modules linked in: igb dca thunderbolt fuse vfat fat elan_i2c mei_wdt
  mei_hdcp i915 wmi_bmof intel_wmi_thunderbolt iTCO_wdt
  iTCO_vendor_support x86_pkg_temp_thermal intel_powerclamp joydev
  coretemp crct10dif_pclmul crc32_pclmul i2c_algo_bit ghash_clmulni_intel
  intel_cstate drm_kms_helper intel_uncore syscopyarea sysfillrect
  sysimgblt fb_sys_fops intel_rapl_perf intel_xhci_usb_role_switch mei_me
  drm roles idma64 i2c_i801 ucsi_acpi typec_ucsi mei intel_lpss_pci
  processor_thermal_device typec intel_pch_thermal intel_soc_dts_iosf
  intel_lpss int3403_thermal thinkpad_acpi wmi int340x_thermal_zone
  ledtrig_audio int3400_thermal acpi_thermal_rel acpi_pad video
  pcc_cpufreq ip_tables serio_raw nvme nvme_core crc32c_intel uas
  usb_storage e1000e i2c_dev
  CPU: 7 PID: 516 Comm: kworker/u16:3 Not tainted 5.2.0-rc1Lyude-Test+ #14
  Hardware name: LENOVO 20L8S2N800/20L8S2N800, BIOS N22ET35W (1.12 ) 04/09/2018
  Workqueue: kacpi_hotplug acpi_hotplug_work_fn
  RIP: 0010:igb_rd32+0x57/0x6a [igb]
  Code: 87 b8 fc ff ff 48 c7 47 08 00 00 00 00 48 c7 c6 33 42 9b c0 4c 89
  c7 e8 47 45 cd dc 89 ee 48 c7 c7 43 42 9b c0 e8 c1 94 71 dc <0f> 0b eb
  08 8b 00 ff c0 75 b0 eb c8 44 89 e0 5d 41 5c c3 0f 1f 44
  RSP: 0018:ffffba5801cf7c48 EFLAGS: 00010286
  RAX: 0000000000000000 RBX: ffff9e7956608840 RCX: 0000000000000007
  RDX: 0000000000000000 RSI: ffffba5801cf7b24 RDI: ffff9e795e3d6a00
  RBP: 0000000000000018 R08: 000000009dec4a01 R09: ffffffff9e61018f
  R10: 0000000000000000 R11: ffffba5801cf7ae5 R12: 00000000ffffffff
  R13: ffff9e7956608840 R14: ffff9e795a6f10b0 R15: 0000000000000000
  FS:  0000000000000000(0000) GS:ffff9e795e3c0000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000564317bc4088 CR3: 000000010e00a006 CR4: 00000000003606e0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  Call Trace:
   igb_release_hw_control+0x1a/0x30 [igb]
   igb_remove+0xc5/0x14b [igb]
   pci_device_remove+0x3b/0x93
   device_release_driver_internal+0xd7/0x17e
   pci_stop_bus_device+0x36/0x75
   pci_stop_bus_device+0x66/0x75
   pci_stop_bus_device+0x66/0x75
   pci_stop_and_remove_bus_device+0xf/0x19
   trim_stale_devices+0xc5/0x13a
   ? __pm_runtime_resume+0x6e/0x7b
   trim_stale_devices+0x103/0x13a
   ? __pm_runtime_resume+0x6e/0x7b
   trim_stale_devices+0x103/0x13a
   acpiphp_check_bridge+0xd8/0xf5
   acpiphp_hotplug_notify+0xf7/0x14b
   ? acpiphp_check_bridge+0xf5/0xf5
   acpi_device_hotplug+0x357/0x3b5
   acpi_hotplug_work_fn+0x1a/0x23
   process_one_work+0x1a7/0x296
   worker_thread+0x1a8/0x24c
   ? process_scheduled_works+0x2c/0x2c
   kthread+0xe9/0xee
   ? kthread_destroy_worker+0x41/0x41
   ret_from_fork+0x35/0x40
  ---[ end trace 252bf10352c63d22 ]---
Signed-off-by: NLyude Paul <lyude@redhat.com>
Fixes: 47e16692 ("igb/igc: warn when fatal read failure happens")
Acked-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Acked-by: NFeng Tang <feng.tang@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When CONFIG_PM_SLEEP is not defined compiler complain as follow:
CC [M]  drivers/net/ethernet/intel/e1000e/netdev.o
drivers/net/ethernet/intel/e1000e/netdev.c:6302:12: warning: ‘e1000e_s0ix_entry_flow’ defined but not used [-Wunused-function]
static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)
drivers/net/ethernet/intel/e1000e/netdev.c:6411:12: warning: ‘e1000e_s0ix_exit_flow’ defined but not used [-Wunused-function]
static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)
LD [M]  drivers/net/ethernet/intel/e1000e/e1000e.o

Add wrap to fix these warnings.
Reported-by: Nkbuild test robot <lpk@intel.com>
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add devices ID's for the next LOM generations that will be
available on the next Intel Client platform (Tiger Lake)
This patch provides the initial support for these devices
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on a series from Alexander Duyck this change adds UDP segmentation
offload support to the i40e driver.

CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: NJosh Hunt <johunt@akamai.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Repost from a series by Alexander Duyck to add UDP segmentation offload
support to the igb driver:
https://lore.kernel.org/netdev/20180504003916.4769.66271.stgit@localhost.localdomain/

CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Willem de Bruijn <willemb@google.com>
Suggested-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJosh Hunt <johunt@akamai.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on a series from Alexander Duyck this change adds UDP segmentation
offload support to the igb driver.

CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: NJosh Hunt <johunt@akamai.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we no longer check for __E1000_DOWN in e1000e_close we can drop the
spot where we were restoring the bit. This saves us a bit of unnecessary
complexity.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to address possible race conditions that can exist
between network configuration and power management. A similar issue was
fixed for igb in commit 9474933c ("igb: close/suspend race in
netif_device_detach").

In addition it consolidates the code so that the PCI error handling code
will essentially perform the power management freeze on the device prior to
attempting a reset, and will thaw the device afterwards if that is what it
is planning to do. Otherwise when we call close on the interface it should
see it is detached and not attempt to call the logic to down the interface
and free the IRQs again.

From what I can tell the check that was adding the check for __E1000_DOWN
in e1000e_close was added when runtime power management was added. However
it should not be relevant for us as we perform a call to
pm_runtime_get_sync before we call e1000_down/free_irq so it should always
be back up before we call into this anyway.
Reported-by: NMorumuri Srivalli <smorumu1@in.ibm.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: NDavid Dai <zdai@linux.vnet.ibm.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>

Add devices ID's for the next LOM generations that will be
available on the next Intel Client platform (Comet Lake)
This patch provides the initial support for these devices
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In i40e_setup_macvlans if i40e_setup_channel fails the allocated memory
for ch should be released.
Signed-off-by: NNavid Emamdoost <navid.emamdoost@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch prepares ground for the next VF MAC address change fix.
It lets untrusted VF to delete any VF mac filter, but it still
doesn't let untrusted VF to add mac filter not setup by PF.
It removes information duplication in num_mac mac filters counter.
And improves exact h/w mac filters usage checking in the
i40e_check_vf_permission() function by counting mac2add_cnt.
It also improves logging because now all mac addresses will be validated
first and corresponding messages will be logged.
Signed-off-by: NAleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>