ice: add ethtool -m support for reading i2c eeprom modules

Implement ethtool -m support to read eeprom data from SFP/QSFP modules.
Signed-off-by: NScott W Taylor <scott.w.taylor@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers/net/ethernet/intel/ice/ice_adminq_cmd.h

@@ -1147,6 +1147,33 @@ struct ice_aqc_set_port_id_led {
 	u8 rsvd[13];
 };
 
+/* Read/Write SFF EEPROM command (indirect 0x06EE) */
+struct ice_aqc_sff_eeprom {
+	u8 lport_num;
+	u8 lport_num_valid;
+#define ICE_AQC_SFF_PORT_NUM_VALID	BIT(0)
+	__le16 i2c_bus_addr;
+#define ICE_AQC_SFF_I2CBUS_7BIT_M	0x7F
+#define ICE_AQC_SFF_I2CBUS_10BIT_M	0x3FF
+#define ICE_AQC_SFF_I2CBUS_TYPE_M	BIT(10)
+#define ICE_AQC_SFF_I2CBUS_TYPE_7BIT	0
+#define ICE_AQC_SFF_I2CBUS_TYPE_10BIT	ICE_AQC_SFF_I2CBUS_TYPE_M
+#define ICE_AQC_SFF_SET_EEPROM_PAGE_S	11
+#define ICE_AQC_SFF_SET_EEPROM_PAGE_M	(0x3 << ICE_AQC_SFF_SET_EEPROM_PAGE_S)
+#define ICE_AQC_SFF_NO_PAGE_CHANGE	0
+#define ICE_AQC_SFF_SET_23_ON_MISMATCH	1
+#define ICE_AQC_SFF_SET_22_ON_MISMATCH	2
+#define ICE_AQC_SFF_IS_WRITE		BIT(15)
+	__le16 i2c_mem_addr;
+	__le16 eeprom_page;
+#define  ICE_AQC_SFF_EEPROM_BANK_S 0
+#define  ICE_AQC_SFF_EEPROM_BANK_M (0xFF << ICE_AQC_SFF_EEPROM_BANK_S)
+#define  ICE_AQC_SFF_EEPROM_PAGE_S 8
+#define  ICE_AQC_SFF_EEPROM_PAGE_M (0xFF << ICE_AQC_SFF_EEPROM_PAGE_S)
+	__le32 addr_high;
+	__le32 addr_low;
+};
+
 /* NVM Read command (indirect 0x0701)
  * NVM Erase commands (direct 0x0702)
  * NVM Update commands (indirect 0x0703)
@@ -1618,6 +1645,7 @@ struct ice_aq_desc {
 		struct ice_aqc_get_phy_caps get_phy;
 		struct ice_aqc_set_phy_cfg set_phy;
 		struct ice_aqc_restart_an restart_an;
+		struct ice_aqc_sff_eeprom read_write_sff_param;
 		struct ice_aqc_set_port_id_led set_port_id_led;
 		struct ice_aqc_get_sw_cfg get_sw_conf;
 		struct ice_aqc_sw_rules sw_rules;
@@ -1741,6 +1769,7 @@ enum ice_adminq_opc {
 	ice_aqc_opc_set_event_mask			= 0x0613,
 	ice_aqc_opc_set_mac_lb				= 0x0620,
 	ice_aqc_opc_set_port_id_led			= 0x06E9,
+	ice_aqc_opc_sff_eeprom				= 0x06EE,
 
 	/* NVM commands */
 	ice_aqc_opc_nvm_read				= 0x0701,

drivers/net/ethernet/intel/ice/ice_common.c

@@ -2555,6 +2555,52 @@ ice_aq_set_port_id_led(struct ice_port_info *pi, bool is_orig_mode,
 	return ice_aq_send_cmd(hw, &desc, NULL, 0, cd);
 }
 
+/**
+ * ice_aq_sff_eeprom
+ * @hw: pointer to the HW struct
+ * @lport: bits [7:0] = logical port, bit [8] = logical port valid
+ * @bus_addr: I2C bus address of the eeprom (typically 0xA0, 0=topo default)
+ * @mem_addr: I2C offset. lower 8 bits for address, 8 upper bits zero padding.
+ * @page: QSFP page
+ * @set_page: set or ignore the page
+ * @data: pointer to data buffer to be read/written to the I2C device.
+ * @length: 1-16 for read, 1 for write.
+ * @write: 0 read, 1 for write.
+ * @cd: pointer to command details structure or NULL
+ *
+ * Read/Write SFF EEPROM (0x06EE)
+ */
+enum ice_status
+ice_aq_sff_eeprom(struct ice_hw *hw, u16 lport, u8 bus_addr,
+		  u16 mem_addr, u8 page, u8 set_page, u8 *data, u8 length,
+		  bool write, struct ice_sq_cd *cd)
+{
+	struct ice_aqc_sff_eeprom *cmd;
+	struct ice_aq_desc desc;
+	enum ice_status status;
+
+	if (!data || (mem_addr & 0xff00))
+		return ICE_ERR_PARAM;
+
+	ice_fill_dflt_direct_cmd_desc(&desc, ice_aqc_opc_sff_eeprom);
+	cmd = &desc.params.read_write_sff_param;
+	desc.flags = cpu_to_le16(ICE_AQ_FLAG_RD | ICE_AQ_FLAG_BUF);
+	cmd->lport_num = (u8)(lport & 0xff);
+	cmd->lport_num_valid = (u8)((lport >> 8) & 0x01);
+	cmd->i2c_bus_addr = cpu_to_le16(((bus_addr >> 1) &
+					 ICE_AQC_SFF_I2CBUS_7BIT_M) |
+					((set_page <<
+					  ICE_AQC_SFF_SET_EEPROM_PAGE_S) &
+					 ICE_AQC_SFF_SET_EEPROM_PAGE_M));
+	cmd->i2c_mem_addr = cpu_to_le16(mem_addr & 0xff);
+	cmd->eeprom_page = cpu_to_le16((u16)page << ICE_AQC_SFF_EEPROM_PAGE_S);
+	if (write)
+		cmd->i2c_bus_addr |= cpu_to_le16(ICE_AQC_SFF_IS_WRITE);
+
+	status = ice_aq_send_cmd(hw, &desc, data, length, cd);
+	return status;
+}
+
 /**
  * __ice_aq_get_set_rss_lut
  * @hw: pointer to the hardware structure

drivers/net/ethernet/intel/ice/ice_common.h

@@ -117,6 +117,10 @@ ice_aq_set_mac_loopback(struct ice_hw *hw, bool ena_lpbk, struct ice_sq_cd *cd);
 enum ice_status
 ice_aq_set_port_id_led(struct ice_port_info *pi, bool is_orig_mode,
 		       struct ice_sq_cd *cd);
+enum ice_status
+ice_aq_sff_eeprom(struct ice_hw *hw, u16 lport, u8 bus_addr,
+		  u16 mem_addr, u8 page, u8 set_page, u8 *data, u8 length,
+		  bool write, struct ice_sq_cd *cd);
 
 enum ice_status
 ice_dis_vsi_txq(struct ice_port_info *pi, u16 vsi_handle, u8 tc, u8 num_queues,

drivers/net/ethernet/intel/ice/ice_ethtool.c

@@ -3455,6 +3455,151 @@ ice_set_per_q_coalesce(struct net_device *netdev, u32 q_num,
 	return __ice_set_coalesce(netdev, ec, q_num);
 }
 
+#define ICE_I2C_EEPROM_DEV_ADDR		0xA0
+#define ICE_I2C_EEPROM_DEV_ADDR2	0xA2
+#define ICE_MODULE_TYPE_SFP		0x03
+#define ICE_MODULE_TYPE_QSFP_PLUS	0x0D
+#define ICE_MODULE_TYPE_QSFP28		0x11
+#define ICE_MODULE_SFF_ADDR_MODE	0x04
+#define ICE_MODULE_SFF_DIAG_CAPAB	0x40
+#define ICE_MODULE_REVISION_ADDR	0x01
+#define ICE_MODULE_SFF_8472_COMP	0x5E
+#define ICE_MODULE_SFF_8472_SWAP	0x5C
+#define ICE_MODULE_QSFP_MAX_LEN		640
+
+/**
+ * ice_get_module_info - get SFF module type and revision information
+ * @netdev: network interface device structure
+ * @modinfo: module EEPROM size and layout information structure
+ */
+static int
+ice_get_module_info(struct net_device *netdev,
+		    struct ethtool_modinfo *modinfo)
+{
+	struct ice_netdev_priv *np = netdev_priv(netdev);
+	struct ice_vsi *vsi = np->vsi;
+	struct ice_pf *pf = vsi->back;
+	struct ice_hw *hw = &pf->hw;
+	enum ice_status status;
+	u8 sff8472_comp = 0;
+	u8 sff8472_swap = 0;
+	u8 sff8636_rev = 0;
+	u8 value = 0;
+
+	status = ice_aq_sff_eeprom(hw, 0, ICE_I2C_EEPROM_DEV_ADDR, 0x00, 0x00,
+				   0, &value, 1, 0, NULL);
+	if (status)
+		return -EIO;
+
+	switch (value) {
+	case ICE_MODULE_TYPE_SFP:
+		status = ice_aq_sff_eeprom(hw, 0, ICE_I2C_EEPROM_DEV_ADDR,
+					   ICE_MODULE_SFF_8472_COMP, 0x00, 0,
+					   &sff8472_comp, 1, 0, NULL);
+		if (status)
+			return -EIO;
+		status = ice_aq_sff_eeprom(hw, 0, ICE_I2C_EEPROM_DEV_ADDR,
+					   ICE_MODULE_SFF_8472_SWAP, 0x00, 0,
+					   &sff8472_swap, 1, 0, NULL);
+		if (status)
+			return -EIO;
+
+		if (sff8472_swap & ICE_MODULE_SFF_ADDR_MODE) {
+			modinfo->type = ETH_MODULE_SFF_8079;
+			modinfo->eeprom_len = ETH_MODULE_SFF_8079_LEN;
+		} else if (sff8472_comp &&
+			   (sff8472_swap & ICE_MODULE_SFF_DIAG_CAPAB)) {
+			modinfo->type = ETH_MODULE_SFF_8472;
+			modinfo->eeprom_len = ETH_MODULE_SFF_8472_LEN;
+		} else {
+			modinfo->type = ETH_MODULE_SFF_8079;
+			modinfo->eeprom_len = ETH_MODULE_SFF_8079_LEN;
+		}
+		break;
+	case ICE_MODULE_TYPE_QSFP_PLUS:
+	case ICE_MODULE_TYPE_QSFP28:
+		status = ice_aq_sff_eeprom(hw, 0, ICE_I2C_EEPROM_DEV_ADDR,
+					   ICE_MODULE_REVISION_ADDR, 0x00, 0,
+					   &sff8636_rev, 1, 0, NULL);
+		if (status)
+			return -EIO;
+		/* Check revision compliance */
+		if (sff8636_rev > 0x02) {
+			/* Module is SFF-8636 compliant */
+			modinfo->type = ETH_MODULE_SFF_8636;
+			modinfo->eeprom_len = ICE_MODULE_QSFP_MAX_LEN;
+		} else {
+			modinfo->type = ETH_MODULE_SFF_8436;
+			modinfo->eeprom_len = ICE_MODULE_QSFP_MAX_LEN;
+		}
+		break;
+	default:
+		netdev_warn(netdev,
+			    "SFF Module Type not recognized.\n");
+		return -EINVAL;
+	}
+	return 0;
+}
+
+/**
+ * ice_get_module_eeprom - fill buffer with SFF EEPROM contents
+ * @netdev: network interface device structure
+ * @ee: EEPROM dump request structure
+ * @data: buffer to be filled with EEPROM contents
+ */
+static int
+ice_get_module_eeprom(struct net_device *netdev,
+		      struct ethtool_eeprom *ee, u8 *data)
+{
+	struct ice_netdev_priv *np = netdev_priv(netdev);
+	u8 addr = ICE_I2C_EEPROM_DEV_ADDR;
+	struct ice_vsi *vsi = np->vsi;
+	struct ice_pf *pf = vsi->back;
+	struct ice_hw *hw = &pf->hw;
+	enum ice_status status;
+	bool is_sfp = false;
+	u16 offset = 0;
+	u8 value = 0;
+	u8 page = 0;
+	int i;
+
+	status = ice_aq_sff_eeprom(hw, 0, addr, offset, page, 0,
+				   &value, 1, 0, NULL);
+	if (status)
+		return -EIO;
+
+	if (!ee || !ee->len || !data)
+		return -EINVAL;
+
+	if (value == ICE_MODULE_TYPE_SFP)
+		is_sfp = true;
+
+	for (i = 0; i < ee->len; i++) {
+		offset = i + ee->offset;
+
+		/* Check if we need to access the other memory page */
+		if (is_sfp) {
+			if (offset >= ETH_MODULE_SFF_8079_LEN) {
+				offset -= ETH_MODULE_SFF_8079_LEN;
+				addr = ICE_I2C_EEPROM_DEV_ADDR2;
+			}
+		} else {
+			while (offset >= ETH_MODULE_SFF_8436_LEN) {
+				/* Compute memory page number and offset. */
+				offset -= ETH_MODULE_SFF_8436_LEN / 2;
+				page++;
+			}
+		}
+
+		status = ice_aq_sff_eeprom(hw, 0, addr, offset, page, !is_sfp,
+					   &value, 1, 0, NULL);
+		if (status)
+			value = 0;
+		data[i] = value;
+	}
+	return 0;
+}
+
 static const struct ethtool_ops ice_ethtool_ops = {
 	.get_link_ksettings	= ice_get_link_ksettings,
 	.set_link_ksettings	= ice_set_link_ksettings,
@@ -3490,6 +3635,8 @@ static const struct ethtool_ops ice_ethtool_ops = {
 	.set_per_queue_coalesce = ice_set_per_q_coalesce,
 	.get_fecparam		= ice_get_fecparam,
 	.set_fecparam		= ice_set_fecparam,
+	.get_module_info	= ice_get_module_info,
+	.get_module_eeprom	= ice_get_module_eeprom,
 };
 
 static const struct ethtool_ops ice_ethtool_safe_mode_ops = {