The remove path does not currently check to see if a
reset is in progress before proceeding.  This can cause
a resource collision resulting in various types of errors.

Check for reset in progress and wait for a reasonable
amount of time before allowing the remove to progress.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Set the carrier state post rebuild by querying the link status. Also
start/stop queues based on link status.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the physical link goes up or down, the driver is supposed to
receive a link status event (LSE). The driver currently has the code
to handle LSEs but there is no firmware support for this feature yet.
So this patch adds the ability for the driver to poll for link status
changes. The polling itself is done in ice_watchdog_subtask.

For namespace cleanliness, this patch also removes code that handles
LSE. This code will be reintroduced once the feature is officially
supported.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Basically remove references to C810 and use E810C (from the branding
string) instead.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update version string to 0.7.2-k
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ice_ena/dis_vsi should have a single differentiating
factor to determine if the netdev_ops call is used or a
direct call to ice_vsi_open/close.  This is if the netif is
running or not.  If netif is running, use ndo_open/ndo_close.
Else, use ice_vsi_open/ice_vsi_close.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch extends the existing malicious driver operation detection
logic to cover malicious operations by the VF driver as well.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When PF gets a link status change event, notify the VFs of the same.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

virtchnl is a protocol/interface specification that allows the Intel
"Adaptive Virtual Function (AVF)" driver (iavf.ko) to work with more than
one physical function driver. The AVF driver sends "virtchnl commands"
(control plane only) to the PF driver over mailbox queues and the PF driver
executes these commands and returns a result to the VF, again over mailbox.

This patch adds AVF support for the ice PF driver by implementing the
following virtchnl commands:

VIRTCHNL_OP_VERSION
VIRTCHNL_OP_GET_VF_RESOURCES
VIRTCHNL_OP_RESET_VF
VIRTCHNL_OP_ADD_ETH_ADDR
VIRTCHNL_OP_DEL_ETH_ADDR
VIRTCHNL_OP_CONFIG_VSI_QUEUES
VIRTCHNL_OP_ENABLE_QUEUES
VIRTCHNL_OP_DISABLE_QUEUES
VIRTCHNL_OP_ADD_ETH_ADDR
VIRTCHNL_OP_DEL_ETH_ADDR
VIRTCHNL_OP_CONFIG_VSI_QUEUES
VIRTCHNL_OP_ENABLE_QUEUES
VIRTCHNL_OP_DISABLE_QUEUES
VIRTCHNL_OP_REQUEST_QUEUES
VIRTCHNL_OP_CONFIG_IRQ_MAP
VIRTCHNL_OP_CONFIG_RSS_KEY
VIRTCHNL_OP_CONFIG_RSS_LUT
VIRTCHNL_OP_GET_STATS
VIRTCHNL_OP_ADD_VLAN
VIRTCHNL_OP_DEL_VLAN
VIRTCHNL_OP_ENABLE_VLAN_STRIPPING
VIRTCHNL_OP_DISABLE_VLAN_STRIPPING
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements handlers for the following NDO operations:

.ndo_set_vf_spoofchk
.ndo_set_vf_mac
.ndo_get_vf_config
.ndo_set_vf_trust
.ndo_set_vf_vlan
.ndo_set_vf_link_state
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Post VF initialization, there are a couple of different ways in which a
VF reset can be triggered. One is when the underlying PF itself goes
through a reset and other is via a VFLR interrupt. ice_reset_vf introduced
in this patch handles both these cases.

Also introduced in this patch is a helper function ice_aq_send_msg_to_vf
to send messages to VF over the mailbox queue. The PF uses this to send
reset notifications to VFs.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements parts of ice_sriov_configure and VF reset flow.

To create virtual functions (VFs), the user sets a value in num_vfs
through sysfs. This results in the kernel calling the handler for
.sriov_configure which is ice_sriov_configure.

VF setup first starts with a VF reset, followed by allocation of the VF
VSI using ice_vf_vsi_setup. Once the VF setup is complete a state bit
ICE_VF_STATE_INIT is set in the vf->states bitmap to indicate that
the VF is ready to go.

Also for VF reset to go into effect, it's necessary to issue a disable
queue command (ice_aqc_opc_dis_txqs). So this patch updates multiple
functions in the disable queue flow to take additional parameters that
distinguish if queues are being disabled due to VF reset.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Mailbox queue is a type of control queue that's used for communication
between PF and VF. This patch adds code to initialize, configure and
use mailbox queues.

This patch also adds support to detect and parse SR-IOV capabilities
returned by the hardware.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the driver is unloaded when traffic is in progress, errors are
generated. Fix this by releasing qvectors and NAPI handler on remove.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently there is no support for dynamic interrupt moderation. This
patch adds some initial code to support this. The following changes
were made:

1. Currently we are using multiple members to store the interrupt
   granularity (itr_gran_25/50/100/200). This is not necessary because
   we can query the device to determine what the interrupt granularity
   should be set to, done by a new function ice_get_itr_intrl_gran.

2. Added intrl to ice_q_vector structure to support interrupt rate
   limiting.

3. Added the function ice_intrl_usecs_to_reg for converting to a value
   in usecs that the device understands.

4. Added call to write to the GLINT_RATE register. Disable intrl by
   default for now.

5. Changed rx/tx_itr_setting to itr_setting because having both seems
   redundant because a ring is either Tx or Rx.

6. Initialize itr_setting for both Tx/Rx rings in ice_vsi_alloc_rings()
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the ice_reset_req enum values have to be translated into
a different set of values that the hardware understands for the same
reset types. Avoid this translation by aligning ice_reset_req enum
values to the ones that the hardware understands.

Also add and else if block to check for ICE_RESET_EMPR and put a dev_dbg
message in the else case.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements ethtool hook for enabling/disabling
RSS. While disabling RSS, the LUT should be cleared. And
the LUT should be reconfigured while enabling RSS.
Signed-off-by: NMd Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For the PF driver, when mapping interrupts to queues, we need to request
IRQs from the kernel and we also have to allocate interrupts from
the device.

Similarly, when the VF driver (iavf.ko) initializes, it requests the kernel
IRQs that it needs but it can't directly allocate interrupts in the device.
Instead, it sends a mailbox message to the ice driver, which then allocates
interrupts in the device on the VF driver's behalf.

Currently both these cases end up having to reserve entries in
pf->irq_tracker but irq_tracker itself is sized based on how many vectors
the PF driver needs. Under the right circumstances, the VF driver can fail
to get entries in irq_tracker, which will result in the VF driver failing
probe.

To fix this, sw_irq_tracker and hw_irq_tracker are introduced. The
sw_irq_tracker tracks only the PF's IRQ request and doesn't play any
role in VF init. hw_irq_tracker represents the device's interrupt space.
When interrupts have to be allocated in the device for either PF or VF,
hw_irq_tracker will be looked up to see if the device has run out of
interrupts.
Signed-off-by: NPreethi Banala <preethi.banala@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We are currently replaying the link state of a port after a reset, but
it is possible that the link state of a port can change during the reset
process. So check for the current link state of a port during the rebuild
process of a reset.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, switch filters get replayed after reset. In addition to
filters, other VSI attributes (like RSS configuration, Tx scheduler
configuration, etc.) also need to be replayed after reset.

Thus, instead of replaying based on functional blocks (i.e. replay
all filters for all VSIs, followed by RSS configuration replay for
all VSIs, and so on), it makes more sense to have the replay centered
around a VSI. In other words, replay all configurations for a VSI before
moving on to rebuilding the next VSI.

To that effect, this patch introduces a VSI replay framework in a new
function ice_vsi_replay_all. Currently it only replays switch filters,
but it will be expanded in the future to replay additional VSI attributes.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is a continuation of the previous patch where VSI
handles are used instead of VSI numbers.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A VSI handle is just a number the driver maintains to uniquely identify
a VSI. A VSI handle is backed by a VSI number in the hardware. When
interacting when the hardware, VSI handles are converted into VSI numbers.

In commit 0f9d5027 ("ice: Refactor VSI allocation, deletion and
rebuild flow"), VSI handles were introduced but it was used only
when creating and deleting VSIs. This patch is part one of two patches
that expands the use of VSI handles across the rest of the driver. Also
in this patch, certain parts of the code had to be refactored to correctly
use VSI handles.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, there is no bit, or set of bits, that protect the entirety
of the reset path.

If the reset is originated by the driver, then the relevant
one of the following bits will be set when the reset is scheduled:
__ICE_PFR_REQ
__ICE_CORER_REQ
__ICE_GLOBR_REQ
This bit will not be cleared until after the rebuild has completed.

If the reset is originated by the FW, then the first the driver knows of
it will be the reception of the OICR interrupt.  The __ICE_RESET_OICR_RECV
bit will be set in the interrupt handler.  This will also be the indicator
in a SW originated reset that we have completed the pre-OICR tasks and
have informed the FW that a reset was requested.

To utilize these bits, change the function:
ice_is_reset_recovery_pending()
	to be:
ice_is_reset_in_progress()

The new function will check all of the above bits in the pf->state and
will return a true if one or more of these bits are set.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch completes the code move out of ice_main.c

The following top level functions and related dependency functions) were
moved to ice_lib.c:
ice_vsi_setup
ice_vsi_cfg_tc

The following functions were made static again:
ice_vsi_setup_vector_base
ice_vsi_alloc_q_vectors
ice_vsi_get_qs
void ice_vsi_map_rings_to_vectors
ice_vsi_alloc_rings
ice_vsi_set_rss_params
ice_vsi_set_num_qs
ice_get_free_slot
ice_vsi_init
ice_vsi_alloc_arrays
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch continues the code move out of ice_main.c

The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_setup_vector_base
ice_vsi_alloc_q_vectors
ice_vsi_get_qs

The following functions were made static again:
ice_vsi_free_arrays
ice_vsi_clear_rings

Also, in this patch, the netdev and NAPI registration logic was de-coupled
from the VSI creation logic (ice_vsi_setup) as for SR-IOV, while we want to
create VF VSIs using ice_vsi_setup, we don't want to create netdevs.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch continues the code move out of ice_main.c

The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_clear
ice_vsi_close
ice_vsi_free_arrays
ice_vsi_map_rings_to_vectors
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch continues the code move out of ice_main.c

The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_alloc_rings
ice_vsi_set_rss_params
ice_vsi_set_num_qs
ice_get_free_slot
ice_vsi_init
ice_vsi_clear_rings
ice_vsi_alloc_arrays
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch continues the code move out of ice_main.c

The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_delete
ice_free_res
ice_get_res
ice_is_reset_recovery_pending
ice_vsi_put_qs
ice_vsi_dis_irq
ice_vsi_free_irq
ice_vsi_free_rx_rings
ice_vsi_free_tx_rings
ice_msix_clean_rings
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch continues the code move out of ice_main.c

The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_start_rx_rings
ice_vsi_stop_rx_rings
ice_vsi_stop_tx_rings
ice_vsi_cfg_rxqs
ice_vsi_cfg_txqs
ice_vsi_cfg_msix
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The functions that are used for PF VSI/netdev setup will also be used
for SR-IOV support. To allow reuse of these functions, move these
functions out of ice_main.c to ice_common.c/ice_lib.c

This move is done across multiple patches. Each patch moves a few
functions and may have minor adjustments. For example, a function that was
previously static in ice_main.c will be made non-static temporarily in
its new location to allow the driver to build cleanly. These adjustments
will be removed in subsequent patches where more code is moved out of
ice_main.c

In this particular patch, the following functions were moved out of
ice_main.c:
int ice_add_mac_to_list
ice_free_fltr_list
ice_stat_update40
ice_stat_update32
ice_update_eth_stats
ice_vsi_add_vlan
ice_vsi_kill_vlan
ice_vsi_manage_vlan_insertion
ice_vsi_manage_vlan_stripping
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update branding strings and remove device ids 0x1594 and 0x1595.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update branding strings and remove device ids 0x1594 and 0x1595.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

ice uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We recently updated all our SPDX identifiers to correctly
indicate our net/ethernet/intel/* drivers were always released
and intended to be released under GPL v2, but the MODULE_LICENSE
declaration was never updated.

Fix the MODULE_LICENSE to be GPL v2, for all our drivers.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the "ice" prefix for the driver version string and bump version
to 0.7.1-k.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch introduces SERVICE_DIS flag to use for stopping service task.
This flag will be checked before scheduling new tasks. Also add new
functions ice_service_task_stop to stop service task.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

VLAN pruning is not valid when VLAN 0 is not active. If VLAN
pruning is enabled and VLAN 0 is not active (8021q driver not loaded)
then normal, non-VLAN, traffic will not pass.

TX/RX VLAN pruning is enabled when the VLAN 0 is added to the
active_vlan bitmap and it is disabled when VLAN 0 is removed from the
active_vlan bitmap.

So, only enable VLAN pruning when VLAN 0 is active. Setting RX VLAN
pruning causes the switch to drop received VLAN packets when there
are no matching VLAN ids in the associated VSI's switch filters. Setting
TX pruning makes it so the switch will not send out any packets with
VLAN tags that don't match the associated VSI's switch filters.

With this patch, if the VF or PF tries to send a VLAN tagged packet with
a VLAN tag that it does not have a pruning rule for it will trigger an
MDD event. For example, if PF0 has VLAN10 and VLAN11 interfaces and
scapy is used to send a packet with VLAN8 then the MDD is triggered.

Also make ice_vsi_kill_vlan return a value which the caller can check
before updating VLAN related data structures (counts, pruning bits, etc.).
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

To enable FW logging, the "cq_en" and "uart_en" enable bits of the
"fw_log" element in struct ice_hw need to set accordingly based on
some user-provided parameters during driver loading. To select which
FW log events to be emitted, the "cfg" elements of corresponding FW
modules in the "evnts" array member of "fw_log" need to be configured.
Signed-off-by: NHieu Tran <hieu.t.tran@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ice_bridge_getlink returns the current bridge mode using
ndo_dflt_bridge_getlink and the mode parameter available in
first_switch->bridge_mode.

ice_bridge_setlink is invoked when the bridge mode needs to
changed. The value to be changed to is available as a netlink
message which is parsed in this function. If the mode has to
be changed, switch_flags is set appropriately (set ALLOW_LB
for VEB mode and clear it for VEPA mode) and ice_aq_update_vsi
is called. Also change the unicast switch filter rules.
Signed-off-by: NMd Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a malicious operation is detected, the firmware triggers an
interrupt, which is then picked up by the service task (specifically by
ice_handle_mdd_event). A reset is scheduled if required.

Tx hang detection works in a similar way, except the logic here monitors
the VSI's Tx queues and tries to revive them if stalled. If the hang is
not resolved, the kernel eventually calls ndo_tx_timeout, which is
handled by ice_tx_timeout.
Signed-off-by: NSudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>