In the unload path, all VSIs are freed. Also free the related VSI
contexts to prevent memory leaks.
Signed-off-by: NVictor Raj <victor.raj@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Setting Rx or Tx pause parameter currently results in link loss on the
interface, requiring the platform/host to be cold power cycled. Fix it.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The remove path does not currently check to see if a
reset is in progress before proceeding.  This can cause
a resource collision resulting in various types of errors.

Check for reset in progress and wait for a reasonable
amount of time before allowing the remove to progress.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Set the carrier state post rebuild by querying the link status. Also
start/stop queues based on link status.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch allows users to enable/disable internal TX and/or RX clock
delay for BCM54616S PHYs so as to satisfy RGMII timing specifications.

On a particular platform, whether TX and/or RX clock delay is required
depends on how PHY connected to the MAC IP. This requirement can be
specified through "phy-mode" property in the platform device tree.

The patch is inspired by commit 73333626 ("net: phy: Allow BCM5481x
PHYs to setup internal TX/RX clock delay").
Signed-off-by: NTao Ren <taoren@fb.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alx_drv_name is not used outside main.c, so there's no reason for it to
have external linkage.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 4d2c0cda set slave->link to
BOND_LINK_DOWN for 802.3ad bonds whenever invalid speed/duplex values
were read, to fix a problem with slaves getting into weird states, but
in the process, broke tracking of link failures, as going straight to
BOND_LINK_DOWN when a link is indeed down (cable pulled, switch rebooted)
means we broke out of bond_miimon_inspect()'s BOND_LINK_DOWN case because
!link_state was already true, we never incremented commit, and never got
a chance to call bond_miimon_commit(), where slave->link_failure_count
would be incremented. I believe the simple fix here is to mark the slave
as BOND_LINK_FAIL, and let bond_miimon_inspect() transition the link from
_FAIL to either _UP or _DOWN, and in the latter case, we now get proper
incrementing of link_failure_count again.

Fixes: 4d2c0cda ("bonding: speed/duplex update at NETDEV_UP event")
CC: Mahesh Bandewar <maheshb@google.com>
CC: David S. Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since 4.19 the following error in sysfs has appeared when using the
r8169 NIC driver:

$cd /sys/module/realtek/drivers
$ls -l
ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory
[..garbled dir entries follow..]

Apparently the forward slash in "10/100Mbps Ethernet" is interpreted
as directory separator that leads nowhere, and was introduced in commit
513588dd ("net: phy: realtek: add RTL8201F phy-id and functions").

Fix this by removing the offending slash in the driver name.

Other drivers in net/phy seem to have the same problem, but I cannot
test/verify them.

Fixes: 513588dd ("net: phy: realtek: add RTL8201F phy-id and functions")
Signed-off-by: NHolger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CPU policer used to police packets being trapped via a local route
(IP2ME) was incorrectly configured to police based on bytes per second
instead of packets per second.

Change the policer to police based on packets per second and avoid
packet loss under certain circumstances.

Fixes: 9148e7cf ("mlxsw: spectrum: Add policers for trap groups")
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc-8 notices that qed_mcp_get_transceiver_data() may fail to
return a result to the caller:

drivers/net/ethernet/qlogic/qed/qed_mcp.c: In function 'qed_mcp_trans_speed_mask':
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1955:2: error: 'transceiver_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]

When an error is returned by qed_mcp_get_transceiver_data(), we
should propagate that to the caller of qed_mcp_trans_speed_mask()
rather than continuing with uninitialized data.

Fixes: c56a8be7 ("qed: Add supported link and advertise link to display in ethtool.")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vport should be initialized to hdev->vport for each bp group,
otherwise it will cause out-of-bounds access and bp setting not
correct problem.

[   35.254124] BUG: KASAN: slab-out-of-bounds in hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[   35.254126] Read of size 2 at addr ffff803b6651581a by task kworker/0:1/14

[   35.254132] CPU: 0 PID: 14 Comm: kworker/0:1 Not tainted 4.19.0-rc7-hulk+ #85
[   35.254133] Hardware name: Huawei D06/D06, BIOS Hisilicon D06 UEFI RC0 - B052 (V0.52) 09/14/2018
[   35.254141] Workqueue: events work_for_cpu_fn
[   35.254144] Call trace:
[   35.254147]  dump_backtrace+0x0/0x2f0
[   35.254149]  show_stack+0x24/0x30
[   35.254154]  dump_stack+0x110/0x184
[   35.254157]  print_address_description+0x168/0x2b0
[   35.254160]  kasan_report+0x184/0x310
[   35.254162]  __asan_load2+0x7c/0xa0
[   35.254170]  hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[   35.254177]  hclge_tm_init_hw+0x794/0x9f0 [hclge]
[   35.254184]  hclge_tm_schd_init+0x48/0x58 [hclge]
[   35.254191]  hclge_init_ae_dev+0x778/0x1168 [hclge]
[   35.254196]  hnae3_register_ae_dev+0x14c/0x298 [hnae3]
[   35.254206]  hns3_probe+0x88/0xa8 [hns3]
[   35.254210]  local_pci_probe+0x7c/0xf0
[   35.254212]  work_for_cpu_fn+0x34/0x50
[   35.254214]  process_one_work+0x4d4/0xa38
[   35.254216]  worker_thread+0x55c/0x8d8
[   35.254219]  kthread+0x1b0/0x1b8
[   35.254222]  ret_from_fork+0x10/0x1c

[   35.254224] The buggy address belongs to the page:
[   35.254228] page:ffff7e00ed994400 count:1 mapcount:0 mapping:0000000000000000 index:0x0 compound_mapcount: 0
[   35.273835] flags: 0xfffff8000008000(head)
[   35.282007] raw: 0fffff8000008000 dead000000000100 dead000000000200 0000000000000000
[   35.282010] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[   35.282012] page dumped because: kasan: bad access detected

[   35.282014] Memory state around the buggy address:
[   35.282017]  ffff803b66515700: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282019]  ffff803b66515780: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282021] >ffff803b66515800: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282022]                             ^
[   35.282024]  ffff803b66515880: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282026]  ffff803b66515900: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282028] ==================================================================
[   35.282029] Disabling lock debugging due to kernel taint
[   35.282747] hclge driver initialization finished.

Fixes: 67bf2541 ("net: hns3: Fixes the back pressure setting when sriov is enabled")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

doorbell only depends on xmit_more and netif_tx_queue_stopped()

Using __netdev_tx_sent_queue() avoids messing with BQL stop flag,
and is more generic.

This patch increases performance on GSO workload by keeping
doorbells to the minimum required.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.

The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcm_sysport_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.

This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcm_sysport_netif_stop. There
are currently only two users of the bcm_sysport_netif_stop function:
close and suspend.

The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.

The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcm_sysport_netif_stop rather than
after it.

These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcm_sysport_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.

For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcm_sysport_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcm_sysport_netif_start so it is moved into the driver open service.

Fixes: 40755a0f ("net: systemport: add suspend and resume support")
Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.

The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcmgenet_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.

This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcmgenet_netif_stop. There
are currently only two users of the bcmgenet_netif_stop function:
close and suspend.

The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.

The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcmgenet_netif_stop rather than
after it.

These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcmgenet_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.

For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcmgenet_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcmgenet_netif_start so it is moved into the driver open service.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initialize mutex before use.  Avoid kernel complaint when
CONFIG_DEBUG_LOCK_ALLOC is enabled.

Fixes: b987e98e ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: NTristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: NPavel Machek <pavel@ucw.cz>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to make sure, that the carrier check polling is disabled
while suspending. Otherwise we can end up with usbnet_read_cmd()
being issued when only usbnet_read_cmd_nopm() is allowed. If this
happens, read operations lock up.

Fixes: d69d1694 ("usbnet: smsc95xx: fix link detection for disabled autonegotiation")
Signed-off-by: NFrieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: NRaghuram Chary J <RaghuramChary.Jallipalli@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When building stmmac, it is only possible to select CONFIG_DWMAC_GENERIC,
or any of the glue drivers, when CONFIG_STMMAC_PLATFORM is set.
The only exception is CONFIG_STMMAC_PCI.

When calling of_mdiobus_register(), it will call our ->reset()
callback, which is set to stmmac_mdio_reset().

Most of the code in stmmac_mdio_reset() is protected by a
"#if defined(CONFIG_STMMAC_PLATFORM)", which will evaluate
to false when CONFIG_STMMAC_PLATFORM=m.

Because of this, the phy reset gpio will only be pulled when
stmmac is built as built-in, but not when built as modules.

Fix this by using "#if IS_ENABLED()" instead of "#if defined()".
Signed-off-by: NNiklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the elaborate private structure global linked-list used in
ntb_netdev_probe() and ntb_netdev_remove() by stashing our private
data in the NTB transport client device.
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Reviewed-by: NLogan Gunthorpe <logang@deltatee.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

The tx_time should be in usecs (according to the comment above the
variable), but the setting of the timer during the rearming is done in
msecs.  Change it to match the expected units.

Fixes: e74bfeed ("NTB: Add flow control to the ntb_netdev")
Suggested-by: NGerd W. Haeussler <gerd.haeussler@cesys-it.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Acked-by: NDave Jiang <dave.jiang@intel.com>

An MC-aware mode was introduced in commit 7b819530 ("mlxsw:
spectrum: Configure MC-aware mode on mlxsw ports"). In MC-aware mode,
BUM traffic gets a special treatment by being assigned to a separate set
of traffic classes 8..15. Pairs of TCs 0 and 8, 1 and 9, etc., are then
configured to strictly prioritize the lower-numbered ones. The intention
is to prevent BUM traffic from flooding the switch and push out all UC
traffic, which would otherwise happen, and instead give UC traffic
precedence.

However strictly prioritizing UC traffic has the effect that UC overload
pushes out all BUM traffic, such as legitimate ARP queries. These
packets are kept in queues for a while, but under sustained UC overload,
their lifetime eventually expires and these packets are dropped. That is
detrimental to network performance as well.

Therefore configure the MC TCs (8..15) with minimum shaper of 200Mbps (a
minimum permitted value) to allow a trickle of necessary control traffic
to get through.

Fixes: 7b819530 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add QEEC.mise (minimum shaper enable) and QEEC.min_shaper_rate to enable
configuration of minimum shaper.

Increase the QEEC length to 0x20 as well: that's the length that the
register has had for a long time now, but with the configurations that
mlxsw typically exercises, the firmware tolerated 0x1C-sized packets.
With mise=true however, FW rejects packets unless they have the full
required length.

Fixes: b9b7cee4 ("mlxsw: reg: Add QoS ETS Element Configuration register")
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since hclgevf_reset_wait() is used to wait for the hardware to complete
the reset, it is not necessary to hold the rtnl_lock during
hclgevf_reset_wait(). So this patch releases the lock for the duration
of hclgevf_reset_wait().

Fixes: 6988eb2a ("net: hns3: Add support to reset the enet/ring mgmt layer")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since hclge_reset_wait() is used to wait for the hardware to complete
the reset, it is not necessary to hold the rtnl_lock during
hclge_reset_wait(). So this patch releases the lock for the duration
of hclge_reset_wait().

Fixes: 6d4fab39 ("net: hns3: Reset net device with rtnl_lock")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a multi-core machine, the mailbox service and reset service
will be executed at the same time. The reset service will re-initialize
the command queue, before that, the mailbox handler can only get some
invalid messages.

The HCLGE_STATE_CMD_DISABLE flag means that the command queue is not
available and needs to be reinitialized. Therefore, when the mailbox
handler recognizes this flag, it should not process the command.

Fixes: dde1a86e ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are some functions that, when they fail to send the command,
need to return the corresponding error value to its caller.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: 681ec399 ("net: hns3: fix for vlan table lost problem when resetting")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When there is a PHY, the driver needs to complete some operations through
MDIO during reset reinitialization, so HCLGE_STATE_CMD_DISABLE is more
suitable than HCLGE_STATE_RST_HANDLING to prevent the MDIO operation from
being sent during the hardware reset.

Fixes: b50ae26c ("net: hns3: never send command queue message to IMP when reset)
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The HEAD pointer of the hardware command queue maybe equal to the command
queue's next_to_use in the driver, so that does not belong to the invalid
HEAD pointer, since the hardware may not process the command in time,
causing the HEAD pointer to be too late to update. The variables' name
in this function is unreadable, so give them a more readable one.

Fixes: 3ff50490 ("net: hns3: fix a dead loop in hclge_cmd_csq_clean")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is not necessary to reset the queue in the hns3_uninit_all_ring(),
since the queue is stopped in the down operation, and will be reset
in the up operation. And the judgment of the HCLGE_STATE_RST_HANDLING
flag in the hclge_reset_tqp() is not correct, because we need to reset
tqp during pf reset, otherwise it may cause queue not being reset to
working state problem.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The spin lock of the command queue only need to be initialized once
when the driver initializes the command queue. It is not necessary to
initialize the spin lock when resetting. At the same time, the
modification of the queue member should be performed after acquiring
the lock.

Fixes: 3efb960f ("net: hns3: Refactor the initialization of command queue")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current driver supports handling two vector0 interrupts, reset and
mailbox. When the hardware reports an interrupt of another type of
interrupt source, if the driver does not process the interrupt, but
enables the interrupt, the hardware will repeatedly report the unknown
interrupt.

Therefore, the driver enables the vector0 interrupt after clearing the
known type of interrupt source. Other conditions are not enabled.

Fixes: cd8c5c26 ("net: hns3: Fix for hclge_reset running repeatly problem")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When hns3_get_ring_config()/hns3_queue_to_ring()/
hns3_get_vector_ring_chain() failed during resetting, the allocated
memory has not been freed before these three functions return. So
this patch adds error handler in these functions to fix it.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When hns3_nic_init_vector_data() fails to map ring to vector,
it should cancel the netif_napi_add() that has been successfully
done and then exits.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As shown by Dmitris, we need to use csum_block_add() instead of csum_add()
when adding the FCS contribution to skb csum.

Before 4.18 (more exactly commit 88078d98 "net: pskb_trim_rcsum()
and CHECKSUM_COMPLETE are friends"), the whole skb csum was thrown away,
so RXFCS changes were ignored.

Then before commit d55bef50 ("net: fix pskb_trim_rcsum_slow() with
odd trim offset") both mlx5 and pskb_trim_rcsum_slow() bugs were canceling
each other.

Now we fixed pskb_trim_rcsum_slow() we need to fix mlx5.

Note that this patch also rewrites mlx5e_get_fcs() to :

- Use skb_header_pointer() instead of reinventing it.
- Use __get_unaligned_cpu32() to avoid possible non aligned accesses
  as Dmitris pointed out.

Fixes: 902a5459 ("net/mlx5e: When RXFCS is set, add FCS data into checksum calculation")
Reported-by: NPaweł Staszewski <pstaszewski@itcare.pl>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Eran Ben Elisha <eranbe@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Dimitris Michailidis <dmichail@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Paweł Staszewski <pstaszewski@itcare.pl>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Tested-By: NMaria Pasechnik <mariap@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in dev_err message
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change resolves a driver bug where the driver is logging a
message that says "Spoofed packets detected". This can occur on the PF
(host) when a VF has VLAN+MACVLAN enabled and is re-started with a
different MAC address.

MAC and VLAN anti-spoofing filters are to be enabled together.
Signed-off-by: NRadoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Acked-by: NPiotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a few new status code which will be used by the ice driver, and
rename a few to make them more consistent. Error code are mapped to
similar values as in i40e_status.h, so as to be compatible with older
VF drivers not using this status enum.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on the original work from Arnd Bergmann.

When XFRM_ALGO is not enabled, the new ixgbe IPsec code produces a
link error:

drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.o: In function `ixgbe_ipsec_vf_add_sa':
ixgbe_ipsec.c:(.text+0x1266): undefined reference to `xfrm_aead_get_byname'

Simply selecting XFRM_ALGO from here causes circular dependencies, so
to fix it, we probably want this slightly more complex solution that is
similar to what other drivers with XFRM offload do:

A separate Kconfig symbol now controls whether we include the IPsec
offload code. To keep the old behavior, this is left as 'default y'. The
dependency in XFRM_OFFLOAD still causes a circular dependency but is
not actually needed because this symbol is not user visible, so removing
that dependency on top makes it all work.

CC: Arnd Bergmann <arnd@arndb.de>
CC: Shannon Nelson <shannon.nelson@oracle.com>
Fixes: eda0333a ("ixgbe: add VF IPsec management")
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>

The upstream and out-of-tree drivers are once again at comparable
functionality. It's been a while since we updated the upstream driver
version, so bump it now.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The device IDs for the Ethernet SDI Adapter devices were never added to
the upstream driver. The IDs are already in the pci.ids database, and
are supported by the out-of-tree driver.

Add the device IDs now, so that the upstream driver can recognize and
load these devices.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

VF drivers can trigger PCIe completer aborts any time they read a queue
that they don't own. Even in nominal circumstances, it is not possible
to prevent the VF driver from reading queues it doesn't own. VF drivers
may attempt to read queues it previously owned, but which it no longer
does due to a PF reset.

Normally these completer aborts aren't an issue. However, on some
platforms these trigger machine check errors. This is true even if we
lower their severity from fatal to non-fatal. Indeed, we already have
code for lowering the severity.

We could attempt to mask these errors conditionally around resets, which
is the most common time they would occur. However this would essentially
be a race between the PF and VF drivers, and we may still occasionally
see machine check exceptions on these strictly configured platforms.

Instead, mask the errors entirely any time we resume VFs. By doing so,
we prevent the completer aborts from being sent to the parent PCIe
device, and thus these strict platforms will not upgrade them into
machine check errors.

Additionally, we don't lose any information by masking these errors,
because we'll still report VFs which attempt to access queues via the
FUM_BAD_VF_QACCESS errors.

Without this change, on platforms where completer aborts cause machine
check exceptions, the VF reading queues it doesn't own could crash the
host system. Masking the completer abort prevents this, so we should
mask it for good, and not just around a PCIe reset. Otherwise malicious
or misconfigured VFs could cause the host system to crash.

Because we are masking the error entirely, there is little reason to
also keep setting the severity bit, so that code is also removed.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>