We've had deeper idle states working on omaps for few years now,
but only in the legacy mode. When booted with device tree, the
wake-up events did not have a chance to work until commit
3e6cee17 (pinctrl: single: Add support for wake-up interrupts)
that recently got merged. In addition to that we also needed commit
79d97015 (of/irq: create interrupts-extended property) and
9ec36caf (of/irq: do irq resolution in platform_get_irq) that
are now also merged.

So let's fix the wake-up events for some selected omaps so devices
booted in device tree mode won't just hang if deeper power states
are enabled, and so systems can wake up from suspend to the serial
port event.

Note that there's no longer need to specify the wake-up bit in
the pinctrl settings, the request_irq on the wake-up pin takes
care of that.

Cc: devicetree@vger.kernel.org
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
[tony@atomide.com: updated comments, added board LDP]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Tegra124 only has 4 UARTs. Parts of the documentation hint at a fifth
UART, but this appears to be left-over from earlier SoC documentation.
Remove the non-existent DT node for UART5.

Cc: <stable@vger.kernel.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Few things were out of order:

- removed ARCH_BCM2835 duplicate
- shuffled ARCH_BCM_5301X, ARCH_U8500 and ARCH_U300 around so to keep the
  list sorted

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-by: NDomenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

s/interrupts-names/interrupt-names/g
s/clocks-names/clock-names/g

Some of the binding files and device tree files get this wrong and the
kernel won't be able to pick it up. Fix them up now so that they don't
get widely used.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by : Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: NGrant Likely <grant.likely@linaro.org>

Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Specify the 'clock-latency' property to avoid certain cpufreq governors
from refusing to work with the following error:
  ondemand governor failed, too long transition latency of HW, fallback to performance governor
Reported-by: NMike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: NMike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

BeagleBoard xM A/B has an inverted usb hub enable line vs the xM C
Signed-off-by: NRobert Nelson <robertcnelson@gmail.com>
[tony@atomide.com: updated for missing bracket]
Signed-off-by: NTony Lindgren <tony@atomide.com>

shiraz.hashim@st.com email-id doesn't exist anymore as he has left the
company.  Replace ST's id with shiraz.linux.kernel@gmail.com.

It also updates .mailmap file to fix address for 'git shortlog'.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

In "ARM: dts: am33xx: correcting dt node unit address for usb", the
usb_ctrl_mod and cppi41dma nodes were updated with the correct register
addresses.  However, the dts files that reference these nodes were not
updated, and those devices are no longer being enabled.

This patch corrects the references for the affected dts files.
Signed-off-by: NLeigh Brown <leigh@solinno.co.uk>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove all remaining uses of gpmc,device-nand that have been added since
the property was removed by commit f40739fa ("ARM: dts: OMAP2+:
Simplify NAND support").
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Wrong documentation in pinmux description can be especially confusing.
Keep it proper.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The correct bit is 24 for AHCLKX.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The USB3 PHY driver (ti-pipe3) was updated so that the relevant
clock phandles are expected in the DT node.
Provide the necessary clocks.
Reported-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The default behaviour of the uart-rx pins on the rk3188 is to be pulled up and
a lot of designs use diodes to even prevent them from being raised from the
outside.

Therefore change the rx-pin settings accordingly.

This also fixes a uart receive problem on mass production Radxa Rock boards.
Signed-off-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Fix typo of renesas,groups in the koeslch dt. The kernel has no
renesas,gpios but this should match renesas,groups.

Noticed thanks to similar fix for Lager by Rob Taylor and Ben Dooks.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.

address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.

address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Per bindings of fixed-clock, #clock-cells is a required property.  Let's
add it for those fixed rate clocks.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.

address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

In case the bootloader has incorrectly configured the ALT mode of
MX6SL_PAD_ECSPI1_SS0 pad, we end up with the following probe error:

m25p80 spi0.0: found mr25h256, expected m25p32
m25p80 spi0.0: mr25h256 (32 Kbytes)

In order to avoid this issue, add an entry for MX6SL_PAD_ECSPI1_SS0 pad, so
that kernel configures the ECSPI chip select as GPIO functionality, which
results in correct SPI NOR probe.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The 'remote-endpoint' property should point back to ipu_di1_lvds1
rather than ipu_di0_lvds0.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Since commit (655b43cc staging: imx-drm-core: Use OF graph to find
components and connections between encoder and crtcs), 'crtcs' becomes a
dead property.  Remove it.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Acked-by: NTim Harvey <tharvey@gateworks.com>

With the recent imx-drm device tree binding changes, we need to add IPU
DI ports and endpoints for adapting.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Acked-by: NLothar Waßmann <LW@KARO-electronics.de>

Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

GPIO7_12 switches the D+/D- USB lines on and off. When we use this as
VBUS regulator it means that USB device mode can never work as VBUS is
never turned on in Device mode.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Bit 6,7 are marked as reserved for the ethernet RGMII pins, so avoid
setting these bits.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Those two properties should have been set to zero, which
is the same as not specifying them.

Having address-cells set to 1 causes OF interrupt
mapping routines to add 1 to the interrupt-cells
property and as result fail because all calculations
are off by one.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Fix bindings for STMPE touchscreen controller to match the documented
bindings and the actual bindings used by the driver.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Reviewed-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

On m53evk there are two DRAM chip selects:

CS0 at 0x70000000
CS1 at 0xb0000000

Each bank has a 512MB DRAM, giving a total of 1GB of system DRAM.

Fix the memory layout to describe the hardware appropriately.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

On mx53qsb there are two DRAM chip selects:

CS0 at 0x70000000
CS1 at 0xb0000000

Each bank has a 512MB DRAM, giving a total of 1GB of system DRAM.

Fix the memory layout to describe the hardware appropriately.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

As defined by the common PCI bindings.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Fix probable typo of renesas,groups in the lager dt. The kernel has no
renesas,gpios but this should match renesas,groups.
Signed-off-by: NRob Taylor <rob.taylor@codethink.co.uk>
[ben.dooks@codethink.co.uk: fixup description]
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The mvmdio driver accesses some register of the Ethernet unit. It
therefore takes a reference and enables a clock. However, on Armada
38x, no clock specification was given in the Device Tree, which leads
the mvmdio driver to fail when being used as a module and loaded
before the mvneta driver: it tries to access a register from a
hardware unit that isn't clocked.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1395790439-21332-3-git-send-email-thomas.petazzoni@free-electrons.comAcked-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The mvmdio driver accesses some register of the Ethernet unit. It
therefore takes a reference and enables a clock. However, on Armada
370/XP, no clock specification was given in the Device Tree, which
leads the mvmdio driver to fail when being used as a module and loaded
before the mvneta driver: it tries to access a register from a
hardware unit that isn't clocked.

Cc: stable@vger.kernel.org
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1395790439-21332-2-git-send-email-thomas.petazzoni@free-electrons.comAcked-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add vendor prefixes to compatible strings where they are missing.

Both the I2C and MTD framework ignore the prefix, so adding them has
no effect on backwards compatibility.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1395492360-1865-6-git-send-email-andrew@lunn.chSigned-off-by: NJason Cooper <jason@lakedaemon.net>

The documented vendor prefix for Atmel is 'atmel' not 'at' as used in
these .dts[i] files.

The i2c framework actually ignores the prefix, so making this change
does not cause compatibility issues.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1395492360-1865-4-git-send-email-andrew@lunn.chSigned-off-by: NJason Cooper <jason@lakedaemon.net>