The mtt range was allocated in mtt units but deallocated
in segments. Among the rest, this caused crash during hotplug removal
Reported-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NMarcel Apfelbaum <marcela@mellanox.co.il>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Tested-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If slave device already has a receive handler registered, then the
error unwind of bonding device enslave function is broken.

The following will leave a pointer to freed memory in the slave
device list, causing a later kernel panic.
# modprobe dummy
# ip li add dummy0-1 link dummy0 type macvlan
# modprobe bonding
# echo +dummy0 >/sys/class/net/bond0/bonding/slaves

The fix is to detach the slave (which removes it from the list)
in the unwind path.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Reviewed-by: NNicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rx mode should be reset after resming, so unconditionally updating rx
mode rather than conditionally updating based on the value we
remembered, otherwise unexpected value may be used by the nic after
resuming.

btw. I find and test this when debugging guest hibernation in qemu, as
I did not have a 8139cp card in hand, this patch is untested in a
physical 8139cp card, plase review it carefully.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

delay_eeprom() use long read for Cfg9346 register(offset 0x50) which may read
into the area of reserved register(offset 0x53). Use byte read instead.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This device uses an already existing DevID but since it supports
WoL we need to add the Sub DevID.  It's support of WoL is limited
to the first port.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Support for new 82599 based quad port adapter.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

I2C access is timing critical. Always do a write flush after writing
to the I2CCTL register.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Saw typo in one message, so decided to run spell checker.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix some register reads that had the opcode and register parameters swapped.
Also use define instead of a magic (0x3) number.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Added pause flag for bi-directional flow control advertising to ethtool
settings.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to address possible issues with the IXGBEVF register
defines generating incorrect values when given a complex expression for the
register offset.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
  dt/device: Fix auxdata matching to handle entries without a name override

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  netfilter: ctnetlink: fix timeout calculation
  ipvs: try also real server with port 0 in backup server
  skge: restore rx multicast filter on resume and after config changes
  mlx4_en: nullify cq->vector field when closing completion queue

The get operation was not sending the message that was built to
user-space. This patch also includes the appropriate handling for
the return value of netlink_unicast().

Moreover, fix error codes on error (for example, for non-existing
entry was uncorrect).
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

* 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ASoC: wm8776: add missing break in sample size switch

The current gspca core code has a regression where it no longer properly
falls back to lower alt settings when there is not enough bandwidth.

This causes many iso based usb-1 cameras to not work when plugged into a
usb2 hub or a sandybridge chipset motherboard!

This patch fixes this.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It was found (by Sasha) that if you use a futex located in the gate
area we get stuck in an uninterruptible infinite loop, much like the
ZERO_PAGE issue.

While looking at this problem, PeterZ realized you'll get into similar
trouble when hitting any install_special_pages() mapping.  And are there
still drivers setting up their own special mmaps without page->mapping,
and without special VM or pte flags to make get_user_pages fail?

In most cases, if page->mapping is NULL, we do not need to retry at all:
Linus points out that even /proc/sys/vm/drop_caches poses no problem,
because it ends up using remove_mapping(), which takes care not to
interfere when the page reference count is raised.

But there is still one case which does need a retry: if memory pressure
called shmem_writepage in between get_user_pages_fast dropping page
table lock and our acquiring page lock, then the page gets switched from
filecache to swapcache (and ->mapping set to NULL) whatever the refcount.
Fault it back in to get the page->mapping needed for key->shared.inode.
Reported-by: NSasha Levin <levinsasha928@gmail.com>
Signed-off-by: NHugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The sanity check (timeout < 0) never works; the dividend is unsigned
and so is the division, which should have been a signed division.

	long timeout = (ct->timeout.expires - jiffies) / HZ;
	if (timeout < 0)
		timeout = 0;

This patch converts the time values to signed for the division.
Signed-off-by: NXi Wang <xi.wang@gmail.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

	We should not forget to try for real server with port 0
in the backup server when processing the sync message. We should
do it in all cases because the backup server can use different
forwarding method.
Signed-off-by: NJulian Anastasov <ja@ssi.bg>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Restore skge hardware registers for multicast filtering to their
appropriate values after system resume and after hardware restarts
that are done when changing certain settings.
Signed-off-by: NFlorian Zumbiehl <florz@florz.de>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

be2net gets an async link status notification from the FW when it creates
an MCC queue. There are some cases in which this gratuitous notification
is not received from FW. To cover this explicitly query the link status
in be_open().
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) fix be_vlan_add/rem_vid to return proper status
2) perform appropriate housekeeping if firmware command succeeds.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Caused loss of connectivity when changing ring size.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 10f6dfcf (Revert "sch_netem: Remove classful functionality")
reintroduced classful functionality to netem, but broke basic netem
behavior :

netem uses an t(ime)fifo queue, and store timestamps in skb->cb[]

If qdisc is changed, time constraints are not respected and other qdisc
can destroy skb->cb[] and block netem at dequeue time.

Fix this by always using internal tfifo, and optionally attach a child
qdisc to netem (or a tree of qdiscs)

Example of use :

DEV=eth3
tc qdisc del dev $DEV root
tc qdisc add dev $DEV root handle 30: est 1sec 8sec netem delay 20ms 10ms
tc qdisc add dev $DEV handle 40:0 parent 30:0 tbf \
	burst 20480 limit 20480 mtu 1514 rate 32000bps

qdisc netem 30: root refcnt 18 limit 1000 delay 20.0ms  10.0ms
 Sent 190792 bytes 413 pkt (dropped 0, overlimits 0 requeues 0)
 rate 18416bit 3pps backlog 0b 0p requeues 0
qdisc tbf 40: parent 30: rate 256000bit burst 20Kb/8 mpu 0b lat 0us
 Sent 190792 bytes 413 pkt (dropped 6, overlimits 10 requeues 0)
 backlog 0b 5p requeues 0
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During some debugging I needed to look into how /proc/net/ipv6_route
operated and in my digging I found its calling fib6_clean_all() which uses
"write_lock_bh(&table->tb6_lock)" before doing the walk of the table. I
found this on 2.6.32, but reading the code I believe the same basic idea
exists currently. Looking at the rtnetlink code they are only calling
"read_lock_bh(&table->tb6_lock);" via fib6_dump_table(). While I realize
reading from proc isn't the recommended way of fetching the ipv6 route
table; taking a write lock seems unnecessary and would probably cause
network performance issues.

To verify this I loaded up the ipv6 route table and then ran iperf in 3
cases:
  * doing nothing
  * reading ipv6 route table via proc
    (while :; do cat /proc/net/ipv6_route > /dev/null; done)
  * reading ipv6 route table via rtnetlink
    (while :; do ip -6 route show table all > /dev/null; done)

* Load the ipv6 route table up with:
  * for ((i = 0;i < 4000;i++)); do ip route add unreachable 2000::$i; done

* iperf commands:
  * client: iperf -i 1 -V -c <ipv6 addr>
  * server: iperf -V -s

* iperf results - 3 runs each (in Mbits/sec)
  * nothing: client: 927,927,927 server: 927,927,927
  * proc: client: 179,97,96,113 server: 142,112,133
  * iproute: client: 928,927,928 server: 927,927,927

lock_stat shows taking the write lock is causing the slowdown. Using this
info I decided to write a version of fib6_clean_all() which replaces
write_lock_bh(&table->tb6_lock) with read_lock_bh(&table->tb6_lock). With
this new function I see the same results as with my rtnetlink iperf test.
Signed-off-by: NJosh Hunt <joshhunt00@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While it's not too late fix the recently added RQLEN diag extension
to report rqlen and wqlen in the same way as TCP does.

I.e. for listening sockets the ack backlog length (which is the input
queue length for socket) in rqlen and the max ack backlog length in
wqlen, and what the CINQ/OUTQ ioctls do for established.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently tcp diag reports rqlen and wqlen values similar to how
the CINQ/COUTQ iotcls do. To make unix diag report these values
in the same way move the respective code into helpers.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
  ARM: 7237/1: PL330: Fix driver freeze
  ARM: 7197/1: errata: Remove SMP dependency for erratum 751472
  ARM: 7196/1: errata: Remove SMP dependency for erratum 720789
  ARM: 7220/1: mmc: mmci: Fixup error handling for dma
  ARM: 7214/1: mmc: mmci: Fixup handling of MCI_STARTBITERR

[ Fix indentation of sock_diag*() calls. -DaveM ]
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: plat-orion: make gpiochip label unique
  enable uncompress log on cpuimx35sd
  cpuimx35: fix touchscreen support
  cpuimx35sd: fix Kconfig
  clock-imx35: fix reboot in internal boot mode
  dma: MX3_IPU fix depends
  imx_v4_v5_defconfig: update default configuration
  cpuimx25sd: fix Kconfig
  arm/imx: fix cpufreq section mismatch
  ARM:imx:fix pwm period value
  ARM: OMAP: hwmod data: fix iva and mailbox hwmods for OMAP 3

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: sentelic - fix retrieving number of buttons
  Input: sentelic - release mutex upon register write failure

Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a routine that dumps memory-related values of a socket.
It's made as an array to make it possible to add more stuff
here later without breaking compatibility.

Since v1: The SK_MEMINFO_ constants are in userspace
visible part of sock_diag.h, the rest is under __KERNEL__.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The headers check complains it should include the linux/types.h
withing, thus add this one.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Properly toss existing components around the ifdef __KERNEL__
and include the header into the header-y target.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  ceph: disable use of dcache for readdir etc.

Merge branch 'v3.2-samsung-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung

* 'v3.2-samsung-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: EXYNOS: Remove duplicated SROMC static memory mapping
  ARM: SAMSUNG: Fix build error when selecting CPU_FREQ_S3C24XX_DEBUGFS on S3C2440

This reverts commit de28f25e.

It results in resume problems for various people. See for example

  http://thread.gmane.org/gmane.linux.kernel/1233033
  http://thread.gmane.org/gmane.linux.kernel/1233389
  http://thread.gmane.org/gmane.linux.kernel/1233159
  http://thread.gmane.org/gmane.linux.kernel/1227868/focus=1230877

and the fedora and ubuntu bug reports

  https://bugzilla.redhat.com/show_bug.cgi?id=767248
  https://bugs.launchpad.net/ubuntu/+source/linux/+bug/904569

which got bisected down to the stable version of this commit.
Reported-by: NJonathan Nieder <jrnieder@gmail.com>
Reported-by: NPhil Miller <mille121@illinois.edu>
Reported-by: NPhilip Langdale <philipl@overt.org>
Reported-by: NTim Gardner <tim.gardner@canonical.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <gregkh@suse.de>
Cc: stable@kernel.org    # for stable kernels that applied the original
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>