Replace /include/ (dtc) with #include (C pre-processor) for all Tegra DT
files, so that gcc -E handles the entire include tree, and hence any of
those files can #include some other file e.g. for constant definitions.

This allows future use of #defines and header files in order to define
names for various constants, such as the IDs and flags in GPIO
specifiers. Use of those features will increase the readability of the
device tree files.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This patch updates all Tegra board files so that they contain all the
properties required by the updated USB DT binding. Note that this patch
only adds the new properties and does not yet remove the old properties,
in order to maintain bisectability. The old properties will be removed
once the driver has been updated to assume the new bindings.
Signed-off-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
[swarren: fixed some newly added regulator-name properties to better
match schematic, avoided duplicate regulator-name on Whistler.]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

1. All Tegra20 ULPI reset GPIO DT properties are modified to indicate active
low nature of the GPIO.
2. Placed USB PHY DT node immediately below the EHCI controller DT nodes
and corrected reg value in the name of USB PHY DT node.
Signed-off-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Correct IDs for cdev1 and cdev2 are 94 and 93 respectively.
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
[swarren: split into separate driver and device-tree patches]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Adding the PM configuration of PMC when the platform support suspend
function.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This adds the power gpio key to DT and enable the wakeup of the gpio key
for the device. The Seaboard and paz00 already had the power gpio key
binding and the power key of Whistler was on KBC. So these boards' device
tree didn't include in this patch.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Audio-related clocks need to be represented in the device tree. Update
bindings to describe which clocks are needed, and DT files to include
those clocks.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Adding the bindings of the clock source of PMC in DT.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The GPIO pin of SD slot card detection should active low.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Tested-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

As reset GPIO information is PHY specific detail, adding
it to PHY DT node.
Signed-off-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

No Tegra20 Platform is running PLL_P at another rate than 216MHz, nor is
any using any other PLL as UART source clock. Move attribute into SoC
level dtsi file to slim down board DT files.
Signed-off-by: NLucas Stach <dev@lynxeye.de>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Enable Tegra based keyboard interfacing for keys and provide
all key mapping through DTS file.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Use engineering name 'Tegra20' instead of 'Tegra2'
Signed-off-by: NBryan Wu <pengw@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Enable host1x, and the HDMI output. Harmony also has an optional LCD,
and a VGA output. The former isn't enabled due to potential issues with
having multiple outputs enabled. The latter isn't enabled since the
driver doesn't support VGA yet anyway.

Correct DDC I2C frequency to 100KHz.

Based on work by Thierry Reding for TrimSlice.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The Harmony board has an Analog Devices ADT7461 temperature sensor
connected to the DVC bus. It can be used to monitor the ambient (local)
and on-die (remote) temperatures.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Commit 13511def "regulator: deprecate regulator-compatible DT property"
now allows for simpler content within the regulators node within a PMIC.
Modify all the Tegra device tree files to take advantage of this.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NThierry Reding <thierry.reding@avionic-design.de>

On Harmony, LDO7 does not feed vdd_fuse. Correct the regulator name.
This issue was probably the result of copying Ventana's regulator setup
when creating the Harmony .dts file. No other naming issues appear to
exist.
Reported-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add DT property to tell the TPS6586x that it should provide the
pm_power_off() implementation. This allows "shutdown" to work.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Harmony uses a TPS6586x regulator. Instantiate this, and hook up a
couple of fixed GPIO-controlled regulators too.

Based on Ventana regulator patch by Stephen Warren <swarren@nvidia.com>
and converted to Harmony.

swarren made the following changes:
* Added ldo0 regulator configuration to device tree, and updated
  board-harmony-pcie.c for the new regulator name.
* Fixed vdd_1v05's voltage from 10.5V to 1.05V.
* Modified board-harmony-pcie.c to obtain the en_vdd_1v05 GPIO number at
  run-time from device tree instead of hard-coding it.
* Removed board-harmony{-power.c,.h} now that they're unused.
* Disabled vdd_1v05 regulator; the code in board-harmony-pcie.c hijacks
  this GPIO for now. This will be fixed when the PCIe driver is re-
  written as a driver. The code can't regulator_get("vdd_1v05") right
  now, because the vdd_1v05 regulator's probe gets deferred due to its
  supply being the PMIC, which gets probed after the regulator the first
  time around, and this dependency is only resolved by repeated probing,
  which happens when deferred_probe_initcall() is called, which happens
  in a late initcall, whose runtime order relative to harmony_pcie_init()
  is undefined, since that's also called from a late initcall.
* Removed unused harmony_pcie_initcall().
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Most ARM ${board}.dts files are already named ${soc}-${board}.dts. This
change modifies the Tegra board files to be named the same way for
consistency.

Once a related change is made in U-Boot, this will cause both U-Boot and
the kernel to use the same names for the .dts files and SoC identifiers,
thus allowing U-Boot's recently added "soc" and "board" environment
variables to be used to construct the name of Tegra .dtb files, and hence
allow board-generic U-Boot bootcmd scripts to be written.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The driver supports the new bus-width property, so remove the legacy
support-8bit property.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This patch unifies the current DT MMC bindings documentation and code,
adds generic MMC DT bindings documentation, and updates .dts files for
consistency.

[cjb: typo fixes, addition of max-frequency property]
Signed-off-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

In tegra*.dtsi, set status="disable" for all HW modules that the board
design may choose not to use. Update all boards to specifically enable
any of those modules that are useful by setting status="okay".

This makes board files say which features they do use, rather than which
they don't, which feels more logical. It also makes the .dts files
slightly smaller, at least for existing content.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NOlof Johansson <olof@lixom.net>

Sort the nodes according to the following rules:
* First, any overrides for properties or nodes created by included files,
  in the order they appeared in the include file.
* Second, any nodes with a reg property, in numerical order.
* Third, any nodes without a reg property, in alphabetical order of node
  name.

The second sorting rule at least will probably help if/when we need to
explicitly insert nodes for the various busses in Tegra; that will just
be an indentation change rather than also a node re-ordering.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NOlof Johansson <olof@lixom.net>

DT node names only need to include the unit address if it's required to
make the node name unique. Remove the unnecessary unit addresses.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NOlof Johansson <olof@lixom.net>

Consistently don't place a space after < or before >.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NOlof Johansson <olof@lixom.net>

Ensure that the USB ULPI signals are not tri-stated, and have no pull-
up or pull-down.

Ensure that the pingroup hosting the USB ULPI reset signal (GPIO PV0 or
PV1 depending on the board, so UAC) is not tri-stated, and has no pull-
up or pull-down.

This change appears larger than it is due to the grouping and sorting of
the pin configuration data.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

ULPI PHYs have a reset signal, and different boards use a different GPIO
for this task. Add a property to device tree to represent this.

I'm not sure if adding this property to the EHCI controller node is
entirely correct; perhaps eventually we should have explicit separate
nodes for the various PHYs. However, we don't have that right now, so this
binding seems like a reasonable choice.

Cc: <devicetree-discuss@lists.ozlabs.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This adds a complete pinmux configuration to all Tegra20 device tree
files. This allows removal of board-dt-tegra20.c's use of the pinmux
board files, and the special device tree handling in board-pinmux.c.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NOlof Johansson <olof@lixom.net>

The Tegra PMC (Power Management Controller) interfaces with an external
PMU (Power Management Unit), and controls wake-up from sleep modes.

This initial binding is the bare minimum required to control the PMC's
inversion of the PMU's interrupt signal.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add complete bindings to instantiate and configure the codec and
top-level audio complex on all currently supported boards using the
Tegra+WM8903 audio driver.

On those boards, disable the I2S2 controller since it isn't used.

On boards not using the WM8903 codec, disable all the audio devices;
they can be re-enabled once the relevant codec and ASoC machine drivers
have been ported to device-tree.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Mark any SDHCI controllers that aren't registered by the board files as
disabled in the device-tree files.

In practice, these controllers:

* Have nothing hooked up to them at all, or
* For ports intended for SDIO usage, the drivers for anything that might
  be attached are not in the device-tree yet. If/when drivers appear, the
  SD/MMC port can be re-enabled.

The only possible exception is TrimSlice's mico SD slot, but that wasn't
enabled in the board files before anyway, and doesn't work when all the
SDHCI controllers are enabled anyway.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Mark any serial ports that aren't registered by the board files as disabled
in the device-tree files.

In practice, none of the now-disabled ports ended up succeeding device
probing because of the missing clock-frequency property. However,
explicitly marking the devices disabled has the advantage of squashing
the dev_warn() the failed probe causes, and documenting that we intend
the port not to be used, rather than accidentally left out the property.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The command-lines present in the existing /chosen node are not necessarily
correct for all users. Ideally, we should simply use the command-line
supplied by the boot-loader.

In fact, using the boot-loader's cmdline is quite easy; either the
bootloader fully supports DT, in which case it can modify the DT passed
to the kernel to include its command-line, or CONFIG_APPENDED_DTB can
be used in conjunction with CONFIG_ARM_ATAG_DTB_COMPAT, and the kernel
will substitute the bootloader's command-line into the DT.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

There are no drivers in the kernel at present which can make use of the
memory reserved by /memreserve/, so there is no point reserving it. Remove
/memreserve/ to allow the user more memory. It's also unclear whether any
future driver would actually require /memreserve/, or allocate memory
through some other mechanism.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

For Seaboard's internal eMMC, this makes the difference between a
5.5MB/s and 10.2MB/s transfer rate. On Harmony, there wasn't any
measurable difference on my cheap/slow ~2MB/s card.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The bindings were recently updated to have separate properties for each
type of GPIO. Update the Device Tree source to match that.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Everything required to populate NVIDIA Tegra devices from the device
tree.  This patch adds a new DT_MACHINE_DESC() which matches against
a tegra20 device tree.  So far it only registers the on-chip devices,
but it will be refined in follow on patches to configure clocks and
pin IO from the device tree also.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>