Firmware returns RESOURCE_ACCESS_DENIED for HWRM_TEMP_MONITORY_QUERY for
VFs. This produces unpleasing error messages in the log when temp1_input
is queried via the hwmon sysfs interface from a VF.

The error is harmless and expected, so silence it and return unknown as
the value. Since the device temperature is not particularly sensitive
information, provide flexibility to change this policy in future by
silencing the error rather than avoiding the HWRM call entirely for VFs.

Fixes: cde49a42 ("bnxt_en: Add hwmon sysfs support to read temperature")
Cc: Marc Smith <msmith626@gmail.com>
Reported-by: NMarc Smith <msmith626@gmail.com>
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnxt_fw_reset_task() is run from a delayed workqueue.  The current
code is not cancelling the workqueue in the driver's .remove()
method and it can potentially crash if the device is removed with
the workqueue still pending.

The fix is to clear the BNXT_STATE_IN_FW_RESET flag and then cancel
the delayed workqueue in bnxt_remove_one().  bnxt_queue_fw_reset_work()
also needs to check that this flag is set before scheduling.  This
will guarantee that no rescheduling will be done after it is cancelled.

Fixes: 230d1f0d ("bnxt_en: Handle firmware reset.")
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a PCI error is detected the PCI state could be corrupt, save
the PCI state after initialization and restore it after the slot
reset.

Fixes: 6316ea6d ("bnxt_en: Enable AER support.")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are returning the wrong count for ETH_SS_STATS in get_sset_count()
when XDP or TCs are enabled.  In a recent commit, we got rid of
irrelevant counters when the ring is RX only or TX only, but we
did not make the proper adjustments for the count.  As a result,
when we have XDP or TCs enabled, we are returning an excess count
because some of the rings are TX only.  This causes ethtool -S to
display extra counters with no counter names.

Fix bnxt_get_num_ring_stats() by not assuming that all rings will
always have RX and TX counters in combined mode.

Fixes: 125592fb ("bnxt_en: show only relevant ethtool stats for a TX or RX ring")
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If firmware goes into unstable state, HWRM_NVM_GET_DIR_INFO firmware
command may return zero dir entries. Return error in such case to
avoid zero length dma buffer request.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In rare conditions like two stage OS installation, the
ethtool's get_channels function may be called when the
device is in D3 state, leading to uncorrectable PCI error.
Check netif_running() first before making any query to FW
which involves writing to BAR.

Fixes: db4723b3 ("bnxt_en: Check max_tx_scheduler_inputs value from firmware.")
Signed-off-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RGMII control register at 0x32 indicates the states for the bits
RGMII_TX_CLK_DELAY and RGMII_RX_CLK_DELAY as follows:

  RGMII Transmit/Receive Clock Delay
    0x0 = RGMII transmit clock is shifted with respect to transmit/receive data.
    0x1 = RGMII transmit clock is aligned with respect to transmit/receive data.

This commit fixes the inversed behavior of these bits

Fixes: 736b25af ("net: dp83869: Add RGMII internal delay configuration")
Signed-off-by: NDaniel Gorsulowski <daniel.gorsulowski@esd.eu>
Acked-by: NDan Murphy <dmurphy@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At the time of do_rest, ibmvnic tries to re-initalize the tx_pools
and rx_pools to avoid re-allocating the long term buffer. However
there is a window inside do_reset that the tx_pools and
rx_pools were freed before re-initialized making it possible to deference
null pointers.

This patch fix this issue by always check the tx_pool
and rx_pool are not NULL after ibmvnic_login. If so, re-allocating
the pools. This will avoid getting into calling reset_tx/rx_pools with
NULL adapter tx_pools/rx_pools pointer. Also add null pointer check in
reset_tx_pools and reset_rx_pools to safe handle NULL pointer case.
Signed-off-by: NMingming Cao <mmc@linux.vnet.ibm.com>
Signed-off-by: NDany Madden <drt@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To flush the vid + mc entries from ALE, which is required when a VLAN
interface is removed, driver needs to call cpsw_ale_flush_multicast()
with ALE_PORT_HOST for port mask as these entries are added only for
host port. Without this, these entries remain in the ALE table even
after removing the VLAN interface. cpsw_ale_flush_multicast() calls
cpsw_ale_flush_mcast which expects a port mask to do the job.

Fixes: ed3525ed ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To flush the vid + mc entries from ALE, which is required when a VLAN
interface is removed, driver needs to call cpsw_ale_flush_multicast()
with ALE_PORT_HOST for port mask as these entries are added only for
host port. Without this, these entries remain in the ALE table even
after removing the VLAN interface. cpsw_ale_flush_multicast() calls
cpsw_ale_flush_mcast which expects a port mask to do the job.

Fixes: 15180eca ("net: ethernet: ti: cpsw: fix vlan mcast")
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Every iteration of for_each_child_of_node() decrements
the reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.

Fix a potential memory leak in mt7530.c by inserting of_node_put()
before the break and return statements.

Issue found with Coccinelle.
Signed-off-by: NSumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During a dump, this attribute is essential, it enables the userspace to
know on which interface the context is linked to.

Fixes: 459aa660 ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: NGabriel Ganne <gabriel.ganne@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

check_fcs() was returning bool as 0/1, which was a sign that the sense
 of the function was unclear: false was good, which doesn't really match
 a name like 'check_$thing'.  So rename it to ef100_has_fcs_error(), and
 use proper booleans in the return statements.
Reported-by: Nkernel test robot <lkp@intel.com>
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.

Fix a potential memory leak in felix.c by inserting of_node_put()
before the return statement.

Issue found with Coccinelle.
Signed-off-by: NSumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When devm_gpiod_get_optional() fails, bus should be
freed just like when of_mdiobus_register() fails.

Fixes: 1bddd96c ("net: arc_emac: support the phy reset for emac driver")
Signed-off-by: NDinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clang warns:

drivers/net/dsa/sja1105/sja1105_main.c:3418:38: warning: address of
array 'match->compatible' will always evaluate to 'true'
[-Wpointer-bool-conversion]
        for (match = sja1105_dt_ids; match->compatible; match++) {
        ~~~                          ~~~~~~~^~~~~~~~~~
1 warning generated.

We should check the value of the first character in compatible to see if
it is empty or not. This matches how the rest of the tree iterates over
IDs.

Fixes: 0b0e2997 ("net: dsa: sja1105: use detected device id instead of DT one on mismatch")
Link: https://github.com/ClangBuiltLinux/linux/issues/1139Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The underlying Ethernet device may request necessary tailroom to be
allocated by setting needed_tailroom. This driver should also set
needed_tailroom to request the tailroom needed by the underlying
Ethernet device to be allocated.

Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: NXie He <xie.he.0141@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When this driver is built as a module, I cannot rmmod it after insmoding
it.
This is because that this driver calls ravb_mdio_init() at the time of
probe, and module->refcnt is incremented by alloc_mdio_bitbang() called
after that.
Therefore, even if ifup is not performed, the driver is in use and rmmod
cannot be performed.

$ lsmod
Module                  Size  Used by
ravb                   40960  1
$ rmmod ravb
rmmod: ERROR: Module ravb is in use

Call ravb_mdio_init() at open and free_mdio_bitbang() at close, thereby
rmmod is possible in the ifdown state.

Fixes: c156633f ("Renesas Ethernet AVB driver proper")
Signed-off-by: NYuusuke Ashizuka <ashiduka@fujitsu.com>
Reviewed-by: NSergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When devm_kcalloc() fails, dev should be freed just
like what we've done in the subsequent error paths.

Fixes: 7b78be48 ("net: systemport: Dynamically allocate number of TX rings")
Signed-off-by: NDinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hns_nic_dev_probe allocates ndev, but not free it on
two error handling paths, which may lead to memleak.

Fixes: 63434888 ("net: hns: net: hns: enet adds support of acpi")
Signed-off-by: NDinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

clang static analysis reports this problem

b53_common.c:1583:13: warning: The left expression of the compound
  assignment is an uninitialized value. The computed value will
  also be garbage
        ent.port &= ~BIT(port);
        ~~~~~~~~ ^

ent is set by a successful call to b53_arl_read().  Unsuccessful
calls are caught by an switch statement handling specific returns.
b32_arl_read() calls b53_arl_op_wait() which fails with the
unhandled -ETIMEDOUT.

So add -ETIMEDOUT to the switch statement.  Because
b53_arl_op_wait() already prints out a message, do not add another
one.

Fixes: 1da6df85 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: NTom Rix <trix@redhat.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netvsc_vf_xmit() / dev_queue_xmit() will call VF NIC’s ndo_select_queue
or netdev_pick_tx() again. They will use skb_get_rx_queue() to get the
queue number, so the “skb->queue_mapping - 1” will be used. This may
cause the last queue of VF not been used.

Use skb_record_rx_queue() here, so that the skb_get_rx_queue() called
later will get the correct queue number, and VF will be able to use
all queues.

Fixes: b3bf5666 ("hv_netvsc: defer queue selection to VF")
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using vf_ops->ndo_select_queue, the number of queues of VF is
usually bigger than the synthetic NIC. This condition may happen
often.
Remove "unlikely" from the comparison of ndev->real_num_tx_queues.

Fixes: b3bf5666 ("hv_netvsc: defer queue selection to VF")
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Truncation of DMA_BIT_MASK to 32-bit dma_addr_t is semantically safe,
 but the compiler was warning because it was happening implicitly.
Insert explicit casts to suppress the warnings.
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are a couple of spelling mistakes in comment text. Fix these.
Signed-off-by: NKaige Li <likaige@loongson.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace alloc_etherdev_mq with devm_alloc_etherdev_mqs. In this way,
when probe fails, netdev can be freed automatically.

Fixes: 4d5ae32f ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NWang Hai <wanghai38@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit
   8dcf2ad3 ("net: atlantic: add hwmon getter for MAC temperature")

implemented a read callback with an udelay(10000U). This fails to
compile on ARM because the delay is >1ms. I doubt that it is needed to
spin for 10ms even if possible on x86.

>From looking at the code, the context appears to be preemptible so using
usleep() should work and avoid busy spinning.

Use readx_poll_timeout() in the poll loop.

Fixes: 8dcf2ad3 ("net: atlantic: add hwmon getter for MAC temperature")
Cc: Mark Starovoytov <mstarovoitov@marvell.com>
Cc: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: NSebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most statistics in ena driver are incremented, meaning that a stat's
value is a sum of all increases done to it since driver/queue
initialization.

This patch makes all statistics this way, effectively making missed_tx
statistic incremental.
Also added a comment regarding rx_drops and tx_drops to make it
clearer how these counters are calculated.

Fixes: 11095fdb ("net: ena: add statistics for missed tx packets")
Signed-off-by: NShay Agroskin <shayagr@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ena_del_napi_in_range() function unregisters the napi handler for
rings in a given range.
This function had the following WARN_ON macro:

    WARN_ON(ENA_IS_XDP_INDEX(adapter, i) &&
	    adapter->ena_napi[i].xdp_ring);

This macro prints the call stack if the expression inside of it is
true [1], but the expression inside of it is the wanted situation.
The expression checks whether the ring has an XDP queue and its index
corresponds to a XDP one.

This patch changes the expression to
    !ENA_IS_XDP_INDEX(adapter, i) && adapter->ena_napi[i].xdp_ring
which indicates an unwanted situation.

Also, change the structure of the function. The napi handler is
unregistered for all rings, and so there's no need to check whether the
index is an XDP index or not. By removing this check the code becomes
much more readable.

Fixes: 548c4940 ("net: ena: Implement XDP_TX action")
Signed-off-by: NShay Agroskin <shayagr@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The reset work is scheduled by the timer routine whenever it
detects that a device reset is required (e.g. when a keep_alive signal
is missing).
When releasing device resources in ena_destroy_device() the driver
cancels the scheduling of the timer routine without destroying the reset
work explicitly.

This creates the following bug:
    The driver is suspended and the ena_suspend() function is called
	-> This function calls ena_destroy_device() to free the net device
	   resources
	    -> The driver waits for the timer routine to finish
	    its execution and then cancels it, thus preventing from it
	    to be called again.

    If, in its final execution, the timer routine schedules a reset,
    the reset routine might be called afterwards,and a redundant call to
    ena_restore_device() would be made.

By changing the reset routine we allow it to read the device's state
accurately.
This is achieved by checking whether ENA_FLAG_TRIGGER_RESET flag is set
before resetting the device and making both the destruction function and
the flag check are under rtnl lock.
The ENA_FLAG_TRIGGER_RESET is cleared at the end of the destruction
routine. Also surround the flag check with 'likely' because
we expect that the reset routine would be called only when
ENA_FLAG_TRIGGER_RESET flag is set.

The destruction of the timer and reset services in __ena_shutoff() have to
stay, even though the timer routine is destroyed in ena_destroy_device().
This is to avoid a case in which the reset routine is scheduled after
free_netdev() in __ena_shutoff(), which would create an access to freed
memory in adapter->flags.

Fixes: 8c5c7abd ("net: ena: add power management ops to the ENA driver")
Signed-off-by: NShay Agroskin <shayagr@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Kconfig help text contains the phrase "the the" in the help
text. Fix this.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the ARP monitor is used for link detection, ARP replies are
validated for all slaves (arp_validate=3) and fail_over_mac is set to
active, two slaves of an active-backup bond may get stuck in a state
where both of them are active and pass packets that they receive to
the bond. This state makes IPv6 duplicate address detection fail. The
state is reached thus:
1. The current active slave goes down because the ARP target
   is not reachable.
2. The current ARP slave is chosen and made active.
3. A new slave is enslaved. This new slave becomes the current active
   slave and can reach the ARP target.
As a result, the current ARP slave stays active after the enslave
action has finished and the log is littered with "PROBE BAD" messages:
> bond0: PROBE: c_arp ens10 && cas ens11 BAD
The workaround is to remove the slave with "going back" status from
the bond and re-enslave it. This issue was encountered when DPDK PMD
interfaces were being enslaved to an active-backup bond.

I would be possible to fix the issue in bond_enslave() or
bond_change_active_slave() but the ARP monitor was fixed instead to
keep most of the actions changing the current ARP slave in the ARP
monitor code. The current ARP slave is set as inactive and backup
during the commit phase. A new state, BOND_LINK_FAIL, has been
introduced for slaves in the context of the ARP monitor. This allows
administrators to see how slaves are rotated for sending ARP requests
and attempts are made to find a new active slave.

Fixes: b2220cad ("bonding: refactor ARP active-backup monitor")
Signed-off-by: NJiri Wiesner <jwiesner@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Every iteration of for_each_available_child_of_node() decrements
reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.

Fix a potential memory leak in gianfar.c by inserting of_node_put()
before the goto statement.

Issue found with Coccinelle.
Signed-off-by: NSumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Even after Tx queues are marked stopped, there exists a
small window where the current packet in the normal Tx
path is still being sent out and loopback selftest ends
up corrupting the same Tx ring. So, ensure selftest takes
the Tx lock to synchronize access the Tx ring.

Fixes: 7235ffae ("cxgb4: add loopback ethtool self-test")
Signed-off-by: NGanji Aravind <ganji.aravind@chelsio.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Work request used for sending loopback packet needs to add
the firmware work request only once. So, fix by using
correct structure size.

Fixes: 7235ffae ("cxgb4: add loopback ethtool self-test")
Signed-off-by: NGanji Aravind <ganji.aravind@chelsio.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If efx_nic_init_interrupt fails, or was never run (e.g. due to an earlier
 failure in ef100_net_open), freeing irqs in efx_nic_fini_interrupt is not
 needed and will cause error messages and stack traces.
So instead, only do this if efx_nic_init_interrupt successfully completed,
 as indicated by the new efx->irqs_hooked flag.

Fixes: 965b549f ("sfc_ef100: implement ndo_open/close and EVQ probing")
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If an ef100_net_open() fails, ef100_net_stop() may be called without
 channel->rps_flow_id having been written; thus it may hold the address
 freed by a previous ef100_net_stop()'s call to efx_remove_filters().
 This then causes a double-free when efx_remove_filters() is called
 again, leading to a panic.
To prevent this, after freeing it, overwrite it with NULL.

Fixes: a9dc3d56 ("sfc_ef100: RX filter table management and related gubbins")
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When downing and upping the ef100 filter table, we need to take a write
 lock on efx->filter_sem, not just a read lock, because we may kfree()
 the table pointers.
Without this, resets cause a WARN_ON from efx_rwsem_assert_write_locked().

Fixes: a9dc3d56 ("sfc_ef100: RX filter table management and related gubbins")
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Actually hook up the .rx_buf_hash_valid method in EF100's nic_type.

Fixes: 06888543 ("sfc: check hash is valid before using it")
Reported-by: NMartin Habets <mhabets@solarflare.com>
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remote source MAC addresses can be set on a 'source mode' macvlan
interface via the IFLA_MACVLAN_MACADDR_DATA attribute. This commit
tightens the validation of these MAC addresses to match the validation
already performed when setting or adding a single MAC address via the
IFLA_MACVLAN_MACADDR attribute.

iproute2 uses IFLA_MACVLAN_MACADDR_DATA for its 'macvlan macaddr set'
command, and IFLA_MACVLAN_MACADDR for its 'macvlan macaddr add' command,
which demonstrates the inconsistent behaviour that this commit
addresses:

 # ip link add link eth0 name macvlan0 type macvlan mode source
 # ip link set link dev macvlan0 type macvlan macaddr add 01:00:00:00:00:00
 RTNETLINK answers: Cannot assign requested address
 # ip link set link dev macvlan0 type macvlan macaddr set 01:00:00:00:00:00
 # ip -d link show macvlan0
 5: macvlan0@eth0: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 ...
     link/ether 2e:ac:fd:2d:69:f8 brd ff:ff:ff:ff:ff:ff promiscuity 0
     macvlan mode source remotes (1) 01:00:00:00:00:00 numtxqueues 1 ...

With this change, the 'set' command will (rightly) fail in the same way
as the 'add' command.
Signed-off-by: NAlvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>