The gpio-mxs controller complies with basic_mmio_gpio library.  This
patch converts the driver to use the library.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The patch converts gpio-mxc driver to use generic irq chip.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Sort the gpio makefile and enforce the naming convention gpio-*.c for
gpio drivers.

v2: cleaned up filenames in Kconfig and comment blocks
v3: fixup use of BASIC_MMIO to GENERIC_GPIO for mxc
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The interrupt pin of the PCA953x is active low, and on the rising edge
no interrupt should be produced.
Signed-off-by: NDavid Jander <david@protonic.nl>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The GPIO driver should reside in drivers/gpio.

v3: Change Kconfig option to def_bool y
v2: Make the Kconfig symbol a silent option, dependent on ARCH_EP93XX
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The gpio-mxc controller complies with basic_mmio_gpio library.  The
patch convert the driver to use the library.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The patch makes necessary changes on gpio-mxc as below to turn it
into an upstanding gpio driver.

 * Add a list to save all mx2 ports references, so that
   mx2_gpio_irq_handler can walk through all interrupt status
   registers

 * Use readl/writel to replace mach-specific accessors
   __raw_readl/__raw_writel

 * Change mxc_gpio_init into mxc_gpio_probe function

 * Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to
   be public at all, and also make some other cleanup on
   plat-mxc/include/mach/gpio.h at the same time

And the patch then migrates mach-imx and mach-mx5 to the updated
driver by adding corresponding platform devices.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation.  This patch moves the plat-mxc driver.  Follow up
patches will clean it up and make it a fine upstanding gpio driver.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The patch makes necessary changes on gpio-mxs as below to turn it
into an upstanding gpio driver.

 * Clean up the gpio port definition stuff

 * Use readl/writel to replace mach-specific accessors
   __raw_readl/__raw_writel

 * Change mxs_gpio_init into mxs_gpio_probe function

And it then migrates mach-mxs to the updated driver by adding
corresponding platform devices.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation.  This patch moves the mxs driver.  Follow up patches
will clean it up and make it a fine upstanding example of a gpio
driver.

v2: Removed header file entirely and put struct definition directly
    into driver.  The struct isn't used anywhere else in the kernel.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>

The Samsung GPIO drivers are always built-in when the relevant
platform is selected.  Change the Kconfig symbol to def_bool y
dependant on the platform.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Remove the #define GEN_74X164_GPIO_COUNT since it's only used in
one place and it's meaning is obvious.  Also remove the #define
GEN_74X164_DRIVER_NAME and use spi->modalias to set the gpio chip's
label and the string "74x164" for the driver name.

Reorder the code slightly to remove the need to prototype
gen_74x164_set_value.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

We had a few drivers move from arch/arm into drivers/gpio, but they
don't actually compile without the ARM platform headers etc.  As a
result they were messing up allyesconfig on x86.

Make them depend on ARM.
Reported-by: NIngo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

gpio_{request,free}_array should not (and do not) modify the passed gpio
array, so make the parameter const.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Move OMAP GPIO driver to drivers/gpio.  Builds whenever
CONFIG_ARCH_OMAP=y.
Signed-off-by: NKevin Hilman <khilman@ti.com>

GPIO 1 to 8 are added for TPS65911 chip version. The gpio driver
now handles more than one gpio lines. Subsequent versions of the
chip family can add new GPIO lines with minimal driver changes.
Signed-off-by: NJorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The GPIO driver should reside in drivers/gpio/ for better
organization.
Signed-off-by: NJorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Move the Samsung s5pc100 SoC GPIO driver to drivers/gpio
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Move the Samsung s5pv210 SoC GPIO driver to drivers/gpio
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Move the Samsung Exynos4 series SoCs GPIO driver to drivers/gpio
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

It's common gpiolib for recent Samsung SoCs. Move to drivers/gpio
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NRickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: NMartin Persson <martin.persson@stericsson.com>
[Split off from larger patch]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Useful to check the status of the runtime pin muxing.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Squashed, modified to use chip-internal IRQ trigger state]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This moves the Nomadik GPIO driver out of arch/arm/plat-nomadik
and into the desired location indicated by the subsystem
maintainer.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
[grant.likely: squashed with kconfig fixup]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This moves the U300 GPIO driver out of arch/arm/mach-u300 and into
the desired location indicated by the subsystem maintainer.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

While this is essentially a no-op for this driver, it has the
side effect of letting the PMU driver snoop D3 requests from
the PCI core for this driver.

This is only for langwell, not for whitney point.
Signed-off-by: NKristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

PCA957x is i2c gpio expander, and similar to PCA953x. Although register
configurations are different between PCA957x and PCA953x. They can share
a lot of components, such as IRQ handling, GPIO IN/OUT. So updating PCA953x
driver to support PCA957x chips.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

cs5535-gpio.c has been split into two, with various setup moved
into cs5535-mfd.c.  Given that cs5535-gpio will not load without
the -mfd part, lets make that dependency explicit in Kconfig
Signed-off-by: NEd Wildgoose <kernel@wildgooses.com>
Acked-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.

Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.

Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Acked-by: NRichard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

alpha allmodconfig:

  drivers/gpio/ml_ioh_gpio.c: In function 'ioh_gpio_probe':
  drivers/gpio/ml_ioh_gpio.c:205: error: implicit declaration of function 'kzalloc'
  drivers/gpio/ml_ioh_gpio.c:205: warning: assignment makes pointer from integer without a cast

also fix this:

  drivers/gpio/ml_ioh_gpio.c:145: warning: 'ioh_gpio_save_reg_conf' defined but not used
  drivers/gpio/ml_ioh_gpio.c:154: warning: 'ioh_gpio_restore_reg_conf' defined but not used

Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

alpha allmodconfig:

  drivers/gpio/vx855_gpio.c: In function 'vx855gpio_probe':
  drivers/gpio/vx855_gpio.c:233: error: implicit declaration of function 'kzalloc'
  drivers/gpio/vx855_gpio.c:233: warning: assignment makes pointer from integer without a cast

Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow GPIO_BASIC_MMIO_CORE to be used to provide an accessor library
for implementing GPIO drivers whilst abstracting the register access
detail.  Based on a patch from Anton Vorontsov[1] and adapted to allow
bgpio_chip to be embedded in another structure.

Changes since v1:
	- Register the gpio_chip in the platform device probe

1. https://lkml.org/lkml/2011/4/19/401Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The build files for drivers/gpio has some wording and comments
about the directory being reserved exclusively for GPIO expanders
(according to the gpio.txt file these are on external busses) and
this has been false for some time. We already have PL061 and
Xilinx drivers which are in silicon and now I'm moving more
silicon drivers here, so delete this and reword it a bit.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch allows to trace gpio operations using ftrace
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Make pca953x driver use the simple irq handler since no hardware control
is necessary and the driver lacks an irq_ack function. handle_edge_irq()
calls chip->irq_ack() which crashes since this function does not exist.
Signed-off-by: NErik Botö <erik.boto@pelagicore.com>
Signed-off-by: NRichard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Export function gpiochip_find so that modules can use it.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Since all the drivers are in a 'if GPIOLIB/endif block', the depends on GPIOLIB
is redundant so remove them.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>