The gpio-mxs controller complies with basic_mmio_gpio library.  This
patch converts the driver to use the library.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The patch converts gpio-mxc driver to use generic irq chip.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Sort the gpio makefile and enforce the naming convention gpio-*.c for
gpio drivers.

v2: cleaned up filenames in Kconfig and comment blocks
v3: fixup use of BASIC_MMIO to GENERIC_GPIO for mxc
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The interrupt pin of the PCA953x is active low, and on the rising edge
no interrupt should be produced.
Signed-off-by: NDavid Jander <david@protonic.nl>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The GPIO driver should reside in drivers/gpio.

v3: Change Kconfig option to def_bool y
v2: Make the Kconfig symbol a silent option, dependent on ARCH_EP93XX
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The gpio-mxc controller complies with basic_mmio_gpio library.  The
patch convert the driver to use the library.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The patch makes necessary changes on gpio-mxc as below to turn it
into an upstanding gpio driver.

 * Add a list to save all mx2 ports references, so that
   mx2_gpio_irq_handler can walk through all interrupt status
   registers

 * Use readl/writel to replace mach-specific accessors
   __raw_readl/__raw_writel

 * Change mxc_gpio_init into mxc_gpio_probe function

 * Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to
   be public at all, and also make some other cleanup on
   plat-mxc/include/mach/gpio.h at the same time

And the patch then migrates mach-imx and mach-mx5 to the updated
driver by adding corresponding platform devices.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation.  This patch moves the plat-mxc driver.  Follow up
patches will clean it up and make it a fine upstanding gpio driver.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The patch makes necessary changes on gpio-mxs as below to turn it
into an upstanding gpio driver.

 * Clean up the gpio port definition stuff

 * Use readl/writel to replace mach-specific accessors
   __raw_readl/__raw_writel

 * Change mxs_gpio_init into mxs_gpio_probe function

And it then migrates mach-mxs to the updated driver by adding
corresponding platform devices.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation.  This patch moves the mxs driver.  Follow up patches
will clean it up and make it a fine upstanding example of a gpio
driver.

v2: Removed header file entirely and put struct definition directly
    into driver.  The struct isn't used anywhere else in the kernel.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>

Improve detection of MAX6642 by reading non existing registers (0x04, 0x06
and 0xff). Reading those registers returns the previously read value.
Signed-off-by: NPer Dalen <per.dalen@appeartv.com>
[guenter.roeck@ericsson.com: added second set of register reads]
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

This reverts commit b1c43f82.

It was broken in so many ways, and results in random odd pty issues.

It re-introduced the buggy schedule_work() in flush_to_ldisc() that can
cause endless work-loops (see commit a5660b41: "tty: fix endless
work loop when the buffer fills up").

It also used an "unsigned int" return value fo the ->receive_buf()
function, but then made multiple functions return a negative error code,
and didn't actually check for the error in the caller.

And it didn't actually work at all.  BenH bisected down odd tty behavior
to it:
  "It looks like the patch is causing some major malfunctions of the X
   server for me, possibly related to PTYs.  For example, cat'ing a
   large file in a gnome terminal hangs the kernel for -minutes- in a
   loop of what looks like flush_to_ldisc/workqueue code, (some ftrace
   data in the quoted bits further down).

   ...

   Some more data: It -looks- like what happens is that the
   flush_to_ldisc work queue entry constantly re-queues itself (because
   the PTY is full ?) and the workqueue thread will basically loop
   forver calling it without ever scheduling, thus starving the consumer
   process that could have emptied the PTY."

which is pretty much exactly the problem we fixed in a5660b41.

Milton Miller pointed out the 'unsigned int' issue.
Reported-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: NMilton Miller <miltonm@bga.com>
Cc: Stefan Bigler <stefan.bigler@keymile.com>
Cc: Toby Gray <toby.gray@realvnc.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The Samsung GPIO drivers are always built-in when the relevant
platform is selected.  Change the Kconfig symbol to def_bool y
dependant on the platform.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Since the commit a314c5c0
(leds/leds-gpio: merge platform_driver with of_platform_driver),
the config option LEDS_GPIO_PLATFORM becomes useless, so remove it.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
[grant.likely: also remove LEDS_GPIO_OF for same reason]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Remove the #define GEN_74X164_GPIO_COUNT since it's only used in
one place and it's meaning is obvious.  Also remove the #define
GEN_74X164_DRIVER_NAME and use spi->modalias to set the gpio chip's
label and the string "74x164" for the driver name.

Reorder the code slightly to remove the need to prototype
gen_74x164_set_value.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This function attempts to free one fragment beyond the number of
fragments that were actually mapped.  This patch brings back the limit
to the correct spot.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Tested-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In certain circumstances, we can get an oops from a torn down device.
Most notably this is from CD roms trying to call scsi_ioctl.  The root
cause of the problem is the fact that after scsi_remove_device() has
been called, the queue is fully torn down.  This is actually wrong
since the queue can be used until the sdev release function is called.
Therefore, we add an extra reference to the queue which is released in
sdev->release, so the queue always exists.
Reported-by: NParag Warudkar <parag.lkml@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

The failed_get label is used after the call to clk_get has succeeded, so it
should be moved up above the call to clk_put.

The failed_req labels doesn't do anything different than failed_get, so
delete it.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
expression e1,e2;
statement S;
@@

e1 = clk_get@p1(...);
... when != e1 = e2
    when != clk_put(e1)
    when any
if (...) { ... when != clk_put(e1)
               when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
 } else S
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A recent patch has introduced a regression, where repeating a memcpy
DMA test with shdma module unloading between them skips the DMA channel
configuration. Fix this regression by always configuring the channel
during its allocation.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Currently the DM9000 driver requests the primary interrupt before it
resets the chip and puts it into a known good state. This means that if
the chip is asserting interrupt for some reason we can end up with a
screaming IRQ that the interrupt handler is unable to deal with. Avoid
this by only requesting the interrupt after we've reset the chip so we
know what state it's in.

This started manifesting itself on one of my boards in the past month or
so, I suspect as a result of some core infrastructure changes removing
some form of mitigation against bad behaviour here, even when things boot
it seems that the new code brings the interface up more quickly.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Go to existing error handling code at the end of the function that calls
clk_put.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
expression e1,e2;
statement S;
@@

e1 = clk_get@p1(...);
... when != e1 = e2
    when != clk_put(e1)
    when any
if (...) { ... when != clk_put(e1)
               when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
 } else S
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This avoids messages like this after suspend:

   cdc_ncm 2-1.4:1.6: no reset_resume for driver cdc_ncm?
   cdc_ncm 2-1.4:1.7: no reset_resume for driver cdc_ncm?
   cdc_ncm 2-1.4:1.6: usb0: unregister 'cdc_ncm' usb-0000:00:1d.0-1.4, CDC NCM

This is important for the Ericsson F5521gw GSM/UMTS modem.
Otherwise modemmanager looses the fact that the cdc_ncm and cdc_acm devices
belong together.

The cdc_ether module does the same.
Signed-off-by: NStefan Metzmacher <metze@samba.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Further relax temperature range checks after reading the IA32_TEMPERATURE_TARGET
register. If the register returns a value other than 0 in bits 16..32, assume
that the returned value is correct.

This change applies to both packet and core temperature limits.

Cc: Carsten Emde <C.Emde@osadl.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NFenghua Yu <fenghua.yu@intel.com>

Commit a321cedb excludes CPU models 0xe, 0xf,
0x16, and 0x1a from TjMax temperature adjustment, even though several of those
CPUs are known to have TiMax other than 100 degrees C, and even though the code
in adjust_tjmax() explicitly handles those CPUs and points to a Web document
listing several of the affected CPU IDs.

Reinstate original TjMax adjustment if TjMax can not be determined using the
IA32_TEMPERATURE_TARGET register.

https://bugzilla.kernel.org/show_bug.cgi?id=32582Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Cc: Huaxu Wan <huaxu.wan@linux.intel.com>
Cc: Carsten Emde <C.Emde@osadl.org>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Yong Wang <yong.y.wang@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Tested-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NFenghua Yu <fenghua.yu@intel.com>
Cc: <stable@kernel.org> # .35.x .36.x .37.x .38.x .39.x

Jens' back-merge commit 698567f3 ("Merge commit 'v2.6.39' into
for-2.6.40/core") was incorrectly done, and re-introduced the
DISK_EVENT_MEDIA_CHANGE lines that had been removed earlier in commits

 - 9fd097b1 ("block: unexport DISK_EVENT_MEDIA_CHANGE for
   legacy/fringe drivers")

 - 7eec77a1 ("ide: unexport DISK_EVENT_MEDIA_CHANGE for ide-gd
   and ide-cd")

because of conflicts with the "g->flags" updates near-by by commit
d4dc210f ("block: don't block events on excl write for non-optical
devices")

As a result, we re-introduced the hanging behavior due to infinite disk
media change reports.

Tssk, tssk, people! Don't do back-merges at all, and *definitely* don't
do them to hide merge conflicts from me - especially as I'm likely
better at merging them than you are, since I do so many merges.
Reported-by: NSteven Rostedt <rostedt@goodmis.org>
Cc: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In some cases we can read wrong temperature value. If after that
temperature value will not be updated to good one, we badly configure
tx power parameters and device is unable to send a data.

Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=35932

Cc: stable@kernel.org # 2.6.39+
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is the same fix as

   commit 84105160
   Author: Matteo Croce <technoboy85@gmail.com>
   Date:   Fri Dec 3 02:25:08 2010 +0100

   The ath9k driver subtracts 3 dBm to the txpower as with two radios the
   signal power is doubled.
   The resulting value is assigned in an u16 which overflows and makes
   the card work at full power.

in two more places. I grepped the ath tree and didn't find any others.

Cc: stable@kernel.org
Signed-off-by: NDaniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current temperature range check of MSR_IA32_TEMPERATURE_TARGET
seems too strict to me, some TjMax values documented in
Documentation/hwmon/coretemp wouldn't pass. Relax the check so that
all the documented values pass.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Carsten Emde <C.Emde@osadl.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

The temp_fault sysfs attribute is wrong, it should be temp2_fault instead.
Reported-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NPer Dalen <per.dalen@appeartv.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

blkbk->pending_pages can be NULL here so I added a check for it.
Signed-off-by: NDan Carpenter <error27@gmail.com>
[v1: Redid the loop a bit]
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

...because vbd_size() dereferences bd_disk if bd_part is NULL.

Signed-off-by: Laszlo Ersek<lersek@redhat.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

We were mapping an extra byte (and hence usually an extra page):
iommu_prepare_identity_map() expects to be given an 'end' argument which
is the last byte to be mapped; not the first byte *not* to be mapped.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The comment in domain_remove_one_dev_info() states "No need to compare
PCI domain; it has to be the same". But for the si_domain that isn't
going to be true, as it consists of all the PCI devices that are
identity mapped thus multiple PCI domains can be in si_domain.  The
code needs to validate the PCI domain too.
Signed-off-by: NMike Habeck <habeck@sgi.com>
Signed-off-by: NMike Travis <travis@sgi.com>
Cc: stable@kernel.org
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

When using the 1:1 (identity) PCI DMA remapping, PCI Host Bridge devices
that do not use the IOMMU causes a kernel panic.  Fix that by not
inserting those devices into the si_domain.
Signed-off-by: NMike Travis <travis@sgi.com>
Reviewed-by: NMike Habeck <habeck@sgi.com>
Cc: stable@kernel.org
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The __intel_map_single function is not honoring the passed in DMA mask.
This results in not using the coherent DMA mask when called from
intel_alloc_coherent().
Signed-off-by: NMike Travis <travis@sgi.com>
Acked-by: NChris Wright <chrisw@sous-sol.org>
Reviewed-by: NMike Habeck <habeck@sgi.com>
Cc: stable@kernel.org
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Mike Travis and Mike Habeck reported an issue where iova allocation
would return a range that was larger than a device's dma mask.

https://lkml.org/lkml/2011/3/29/423

The dmar initialization code will reserve all PCI MMIO regions and copy
those reservations into a domain specific iova tree.  It is possible for
one of those regions to be above the dma mask of a device.  It is typical
to allocate iovas with a 32bit mask (despite device's dma mask possibly
being larger) and cache the result until it exhausts the lower 32bit
address space.  Freeing the iova range that is >= the last iova in the
lower 32bit range when there is still an iova above the 32bit range will
corrupt the cached iova by pointing it to a region that is above 32bit.
If that region is also larger than the device's dma mask, a subsequent
allocation will return an unusable iova and cause dma failure.

Simply don't cache an iova that is above the 32bit caching boundary.
Reported-by: NMike Travis <travis@sgi.com>
Reported-by: NMike Habeck <habeck@sgi.com>
Cc: stable@kernel.org
Acked-by: NMike Travis <travis@sgi.com>
Tested-by: NMike Habeck <habeck@sgi.com>
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

When there are a large count of PCI devices, and the pass through
option for iommu is set, much time is spent in the identity_mapping
function hunting though the iommu domains to check if a specific
device is "identity mapped".

Speed up the function by checking the cached info to see if
it's mapped to the static identity domain.
Signed-off-by: NMike Travis <travis@sgi.com>
Reviewed-by: NMike Habeck <habeck@sgi.com>
Cc: stable@kernel.org
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The identity mapping code appears to make the assumption that if the
devices dma_mask is greater than 32bits the device can use identity
mapping.  But that is not true: take the case where we have a 40bit
device in a 44bit architecture. The device can potentially receive a
physical address that it will truncate and cause incorrect addresses
to be used.

Instead check to see if the device's dma_mask is large enough
to address the system's dma_mask.
Signed-off-by: NMike Travis <travis@sgi.com>
Reviewed-by: NMike Habeck <habeck@sgi.com>
Cc: stable@kernel.org
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Commit a97590e5 added unlinking domains from iommus to reciprocate the
iommu from domains unlinking that was already done.  We actually want
to only do this for device domains and never for the static
identity map domain or VM domains.  The SI domain is special and
never freed, while VM domain->id lives in their own special address
space, separate from iommu->domain_ids.

In the current code, a VM can get domain->id zero, then mark that
domain unused when unbound from pci-stub.  This leads to DMAR
write faults when the device is re-bound to the host driver.
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
Cc: stable@kernel.org
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

There are no externally-visible changes with this. In the loop in the
internal __domain_mapping() function, we simply detect if we are mapping:
  - size >= 2MiB, and
  - virtual address aligned to 2MiB, and
  - physical address aligned to 2MiB, and
  - on hardware that supports superpages.

(and likewise for larger superpages).

We automatically use a superpage for such mappings. We never have to
worry about *breaking* superpages, since we trust that we will always
*unmap* the same range that was mapped. So all we need to do is ensure
that dma_pte_clear_range() will also cope with superpages.

Adjust pfn_to_dma_pte() to take a superpage 'level' as an argument, so
it can return a PTE at the appropriate level rather than always
extending the page tables all the way down to level 1. Again, this is
simplified by the fact that we should never encounter existing small
pages when we're creating a mapping; any old mapping that used the same
virtual range will have been entirely removed and its obsolete page
tables freed.

Provide an 'intel_iommu=sp_off' argument on the command line as a
chicken bit. Not that it should ever be required.

==

The original commit seen in the iommu-2.6.git was Youquan's
implementation (and completion) of my own half-baked code which I'd
typed into an email. Followed by half a dozen subsequent 'fixes'.

I've taken the unusual step of rewriting history and collapsing the
original commits in order to keep the main history simpler, and make
life easier for the people who are going to have to backport this to
older kernels. And also so I can give it a more coherent commit comment
which (hopefully) gives a better explanation of what's going on.

The original sequence of commits leading to identical code was:

Youquan Song (3):
      intel-iommu: super page support
      intel-iommu: Fix superpage alignment calculation error
      intel-iommu: Fix superpage level calculation error in dma_pfn_level_pte()

David Woodhouse (4):
      intel-iommu: Precalculate superpage support for dmar_domain
      intel-iommu: Fix hardware_largepage_caps()
      intel-iommu: Fix inappropriate use of superpages in __domain_mapping()
      intel-iommu: Fix phys_pfn in __domain_mapping for sglist pages
Signed-off-by: NYouquan Song <youquan.song@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>