SMP blocks are configured for specific client IDs (ports).
These client IDs can be different from one chip to another for a
given pipe.

e.g.: DMA0 pipe fetch Y component is connected to:
 - port #10 for MDP5 v1.3
 - port #4 for MDP5 v1.6

In order to be compatible for upcoming versions of MDP5, the
client ID list is passed through the MDP5 config module rather
than using a list of hard-coded enum values.
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

MDP block is actually contained inside the MDSS block. For some
chipsets, the base address of the MDP registers is different from the
current (assumed) 0x100 offset.

Like CTL and LM blocks, this changes introduce a dynamic offset
for the MDP instance, which can be found out at runtime, once the
MDSS HW version is read.
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Pingpong register base addresses are different across platforms.
This change adds this information to config table and initialize
the values for 8x74 and 8084.
Signed-off-by: NHai Li <hali@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Up until now, we assume that eDP is tight to intf_0 and HDMI to
intf_3. This information shall actually come from the mdp5_cfg
module since it can change from one chip to another.

v2: rename macro to mdp5_cfg_intf_is_virtual() [pointed by Archit]
v3: add sanity check before writing in INTF_TIMING_ENGINE_EN registers
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Some interfaces (WB, DSI Command Mode) need to be kicked off
through a START Signal. This signal needs to be sent at the right
time and requests in some cases to keep track of the pipeline
status (eg: whether pipeline registers are flushed AND output WB
buffers are ready, in case of WB interface).
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

DSI and WB interfaces need a more complex pipeline configuration
than the current mdp5_ctl_set_intf().

For example, memory output connections need to be selected for
WB. Interface mode (Video vs. Command modes) also need to be
configured for DSI.

This change takes care of configuring the whole pipeline as far
as operation mode goes. DSI and WB interfaces will be added
later.

v2: rename macro to mdp5_cfg_intf_is_virtual() [pointed by Archit]
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
[Remove temp bisectability hack -Rob]
Signed-off-by: NRob Clark <robdclark@gmail.com>

For example, use 'struct mdp5_smp *' everywhere instead of 'void *', but
only declare it as 'struct mdp5_smp;' in common headers, so the struct
body is still private.  The accomplishes the desired modularity while
still letting the compiler provide some type checking for us.
Signed-off-by: NRob Clark <robdclark@gmail.com>

MDP5 currently support one single CRTC with its private pipe.
This change allows the configuration of multiple CRTCs with
the possibility to attach several public planes to these CRTCs.
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

The hardware configuration modification from a version to another
is quite consequent. Introducing a configuration module
(mdp5_cfg) may make things more clear and easier to access when a
new hardware version comes up.
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>