This change adds the support in mdp5 kms driver for single
and dual DSI. Dual DSI case depends on the framework API
and sequence change to support dual data path.

v1: Initial change
v2: Address Rob Clark's comment
- Separate command mode encoder to a new file mdp5_cmd_encoder.c
- Rebase to not depend on msm_drm_sub_dev change
Signed-off-by: NHai Li <hali@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

This change is to make the content in construct_encoder reflect its
name.
Also, DSI connector may be connected to video mode or command mode
encoder, so that 2 different encoders need to be constructed for DSI.
Signed-off-by: NHai Li <hali@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

This TODO can now be removed and replaced by the previous patch
"drm/msm/mdp5: Update headers (add CTL flush bits)"
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Some upcoming targets have more bits to set in CTL_FLUSH
registers.

Example: msm8x16 needs to set TIMING1 bit so that some of the
INTF1's interface registers get flushed.
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

This change adds the hw configuration for msm8x16 chipsets in
mdp5_cfg module.

Note that only one external display interface is present in this
configuration (DSI) but has not been enabled yet. It will be enabled
once drm/msm driver supports DSI connectors.

v2: add CTL flush register's hardware mask [pointed by Archit]
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

SMP blocks are configured for specific client IDs (ports).
These client IDs can be different from one chip to another for a
given pipe.

e.g.: DMA0 pipe fetch Y component is connected to:
 - port #10 for MDP5 v1.3
 - port #4 for MDP5 v1.6

In order to be compatible for upcoming versions of MDP5, the
client ID list is passed through the MDP5 config module rather
than using a list of hard-coded enum values.
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

This patch contains the generated header file of the following
change "drm/msm/mdp5: Get SMP client list from mdp5_cfg".
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

MDP block is actually contained inside the MDSS block. For some
chipsets, the base address of the MDP registers is different from the
current (assumed) 0x100 offset.

Like CTL and LM blocks, this changes introduce a dynamic offset
for the MDP instance, which can be found out at runtime, once the
MDSS HW version is read.
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

This change contains the generated header file for the following
change "drm/msm/mdp5: Separate MDP5 domain from MDSS domain".
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

The width and height in SSPP_SRC_IMG_SIZE register should be the
size of the entire source framebuffer, not the fetch size.
Signed-off-by: NHai Li <hali@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

This change adds the registers in mdp5 ping pong blocks
and split display control registers.
Signed-off-by: NHai Li <hali@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Pingpong register base addresses are different across platforms.
This change adds this information to config table and initialize
the values for 8x74 and 8084.
Signed-off-by: NHai Li <hali@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Up until now, we assume that eDP is tight to intf_0 and HDMI to
intf_3. This information shall actually come from the mdp5_cfg
module since it can change from one chip to another.

v2: rename macro to mdp5_cfg_intf_is_virtual() [pointed by Archit]
v3: add sanity check before writing in INTF_TIMING_ENGINE_EN registers
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Some interfaces (WB, DSI Command Mode) need to be kicked off
through a START Signal. This signal needs to be sent at the right
time and requests in some cases to keep track of the pipeline
status (eg: whether pipeline registers are flushed AND output WB
buffers are ready, in case of WB interface).
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

DSI and WB interfaces need a more complex pipeline configuration
than the current mdp5_ctl_set_intf().

For example, memory output connections need to be selected for
WB. Interface mode (Video vs. Command modes) also need to be
configured for DSI.

This change takes care of configuring the whole pipeline as far
as operation mode goes. DSI and WB interfaces will be added
later.

v2: rename macro to mdp5_cfg_intf_is_virtual() [pointed by Archit]
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
[Remove temp bisectability hack -Rob]
Signed-off-by: NRob Clark <robdclark@gmail.com>

Prepare for pipeline operation mode configuration, in particular
for DSI and WB modes.
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
[Throw in a #define temporarily to keep things bisectable -Rob]
Signed-off-by: NRob Clark <robdclark@gmail.com>

MDP5 hardware has some limitation and requires to avoid flushing
registers more than once between two Vblanks.

This change removes all FLUSH operations (except for HW cursor)
beside the one coming from a CRTC's ->atomic_flush().

This avoid this type of behavior (eg: CRTC + 1 plane overlay):

	[drm:mdp5_crtc_vblank_irq] vblank
	[drm:mdp5_ctl_commit] flush (20048)   CTL + LM0 + RGB0
	[drm:mdp5_ctl_commit] flush (20040)   CTL + LM0
	[drm:mdp5_crtc_vblank_irq] blank
	[drm:mdp5_ctl_commit] flush (20049)   CTL + LM0 + RGB0 + VIG0
	[drm:mdp5_crtc_vblank_irq] blank

and replaces it by:

	[drm:mdp5_crtc_vblank_irq] vblank
	[drm:mdp5_ctl_commit] flush (20048)   CTL + LM0 + RGB0
	[drm:mdp5_crtc_vblank_irq] blank
	[drm:mdp5_ctl_commit] flush (20049)   CTL + LM0 + RGB0 + VIG0
	[drm:mdp5_crtc_vblank_irq] blank

Only *one* FLUSH is called between Vblanks interrupts.
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Use cases like rotation require these hooks to have some context so they
know how to prepare and cleanup the frame buffer correctly.

For i915 specifically, object backing pages need to be mapped differently
for different rotation modes and the driver needs to know which mapping to
instantiate and which to tear down when transitioning between them.

v2: Made passed in states const. (Daniel Vetter)

[airlied: add mdp5 and atmel fixups]
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

In kexec environment, we are more likely to encounter irq's already
enabled from previous environment.  At which point we find that writes
to disable/clear pending irq's are slightly less than useless without
first enabling clocks.

TODO: full blown state read-in so kexec'd kernel can inherit the mode
already setup.
Signed-off-by: NRob Clark <robdclark@gmail.com>

Seems like we just want BLEND_EN and not BLEND_TRANSP_EN (setting the
latter results in black pixels in the cursor image treated as
transparent).
Signed-off-by: NRob Clark <robdclark@gmail.com>

If cursor is set near the edge of the screen, it is not valid to use the
new cursor width/height as the ROI dimensions.  Split out the ROI calc
and use it both cursor_set and cursor_move.
Signed-off-by: NRob Clark <robdclark@gmail.com>

When a CRTC is disabled, no CTL is allocated to it (CRTC->ctl == NULL);
in that case we should not try to FLUSH registers and do nothing instead.

This can happen when we try to move a cursor but the CRTC's CTL
(CONTROL) has not been allocated yet (inactive CRTC).
It can also happens when we .atomic_check()/.atomic_flush() on a
disabled CRTC.

A CTL needs to be kept as long as the CRTC is alive. Releasing it
after the last VBlank is safer than in .atomic_flush().
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Some target have up to 6 layer mixers (LM).
Let the header file access the last LM's base address.
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Commit 0b776d45 ("drm/msm: fix fallout of atomic dpms
changes") has a typo in both mdp5_encoder_helper_funcs and
mdp5_crtc_helper_funcs definitions:

	.dpms entry should be replaced by .disable and .enable

Also fixed a typo in mdp5_encoder_enable().

Note that these typos are only present for MDP5. MDP4 is fine.
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

In case we request a number of SMP blocks which is lower than
the already reserved blocks, we should not try to allocate a
negative number, but 0 blocks instead.
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

This patch implements the hardware accelarated cursor
support for MDP5 platforms.
Signed-off-by: NBeeresh Gopal <gbeeresh@codeaurora.org>
Signed-off-by: NWentao Xu <wentaox@codeaurora.org>
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

mdp5_ctl_set_intf()'s second argument should be "int", not "enum mdp5_intf".
The passed in value is "intf", not "intf_id".
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Modified the hard-coded hdmi connector/encoder implementations in msm drm
driver to support both edp and hdmi.

V1: Initial change

V2: Address Thierry's change
Signed-off-by: NHai Li <hali@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

The patch add support for YUV frame format
for MDP4 platform.
Signed-off-by: NBeeresh Gopal <gbeeresh@codeaurora.org>
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

This change adds the NV12 format support for public planes.
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Both MDP4 and MDP5 share some code as far as YUV support is
concerned. This change adds this information and will be followed
by the actual MDP4 and MDP5 YUV support patches.
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Resync from rnndb database, to pull in register defines for:
 * eDP
 * HDMI/HDCP
 * mdp4/mdp5 YUV support
 * mdp5 hw cursor support
Signed-off-by: NRob Clark <robdclark@gmail.com>

On !SMP systems spinlocks do not exist. Thus checking of they
are active will always fail.

Use
  assert_spin_locked(lock);
instead of
  BUG_ON(!spin_is_locked(lock));
to not BUG() on all UP systems.
Signed-off-by: NBruno Prémont <bonbons@linux-vserver.org>
[robclark: drop stray ')']
Signed-off-by: NRob Clark <robdclark@gmail.com>

As a result of atomic DPMS support, the various prepare/commit hooks get
called in a way that msm dislikes.  We were expecting prepare/commit to
bracket a modeset, which is no longer the case.  This was needed to hold
various extra clk's (such as interface clks) on while we are touching
registers, and in the case of mdp4 holding vblank enabled.

The most straightforward way to deal with this, since we already have
our own atomic_commit(), is to just handle prepare/commit internally to
the driver (with some additional vfuncs for mdp4 vs mdp5), and switch
everything over to instead use the new enable/disable hooks.  It doesn't
really change too much, despite the code motion.  What used to be in the
encoder/crtc dpms() fxns is split out into enable/disable.

We should be able to drop our own enable-state tracking, as the atomic
helpers should do this for us.  But keeping that for the short term for
extra debugging as atomic stablizes.
Signed-off-by: NRob Clark <robdclark@gmail.com>

Only the legacy helpers use these entry points.  Don't populate them
with transitional helpers, since that just makes things more confusing.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
[robclark: reword commit msg]
Signed-off-by: NRob Clark <robdclark@gmail.com>

If crtc <-> encoder linkage changes, we could end up with the CRTC
listening for the wrong error or vsync irqs.  Generally this problem
would correct itself relatively quickly, since we update the global
irqmask after dispatching irqs, but to be sure let the CRTC trigger
update_irq().
Signed-off-by: NRob Clark <robdclark@gmail.com>

We can't have multiple updates pending on a given CRTC, and we don't
want a sync update to race w/ an async update that preceeded it.  So
keep track of which CRTCs have updates in flight, and block later
updates that would conflict.
Signed-off-by: NRob Clark <robdclark@gmail.com>

Useful since this way we can pass around just the state objects and
will get ther real object, too.

Specifically this allows us to again simplify the parameters for
set_crtc_for_plane.

v2: msm already has it's own specific plane_reset hook, don't forget
that one!

v3: Fixup kerneldoc, reported by 0-day builder.

Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com> (v2)
Tested-by: Rob Clark <robdclark@gmail.com> (v2)
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

The ->load_lut() callback is optional, therefore a dummy implementation
is not needed.

Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>