By default the exynos RTC is disabled.  Enable it for snow.  There's
also an external RTC on the max77686 PMIC but we haven't yet enabled
that.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The 'samsung,vbus-gpio' was submitted before pinmux landed for
exynos5250 and uses the old-style gpio specifier.  Fix the two
exynos5250 boards that use it.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add basic EC information to device tree, currently only describing the
keyboard and keymap.
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Now that we have i2c-arbitrator in place on bus 4 we can add the
sbs-battery driver.  Future devices will be added onto bus 4 once
drivers are in good shape.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

We need to use the i2c-arbitrator to talk to any of the devices on i2c
bus 4 on exynos5250-snow so that we don't confuse the embedded
controller (EC).  Add the i2c-arbitrator to the device tree.  As we
add future devices (keyboard, sbs, tps65090) we'll add them on top of
this.

The arbitrated bus is numbered 104 simply as a convenience to make it
easier for people poking around to guess that it might have something
to do with the physical bus 4.

The addition is split between the cros5250-common and the snow device
tree file since not all cros5250-class devices use arbitration.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add default pin state information for all client nodes that require
pin configuration support using pinctrl interface.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The clock frequency of xxti and xusbxti clocks is dependent on the
frequency of the on-board oscillator that is used to generate these
clocks. So allow the frequency of these clocks to be specfied from
device tree.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Adding EHCI device tree node for Exynos5250 along with
the device base adress and gpio line for vbus.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Acked-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This dts file is based on the Snow dts file in the Chromium OS kernel
tree with the following changes:
* Some details have been updated to match the exynos5250-smdk5250.dts
  file from linux-next (as of c11068538994430547722dc9fb515a0ceefd5cb9).
* This file doesn't include references to hardware whose upstream
  support isn't quite there yet.  That includes most i2c devices.
  Note that most i2c busses have been included with no devices.

The Snow dts file is mostly just an include of the "cros5250" dts file
which describes a class of similar boards. Support for other boards has
not yet been send upstream.

With this file and a change to use UART3 for serial output I can:
* Boot to a command line using either SD or EMMC as a root filesystem
* See the power button and lid switch using evtest.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>