- 11 7月, 2012 3 次提交
-
-
由 Jitendra Kalsaria 提交于
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jitendra Kalsaria 提交于
TX queue was being stopped at beginning of send path instead of at the end when last descriptor is used. Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jon Mason 提交于
skb->dev is being unnecessarily set by the driver on packet recieve. eth_type_trans already sets skb->dev to the proper value and it is not referenced anywhere else in the dirver, thus making its setting unnecessary. Signed-off-by: NJon Mason <jdmason@kudzu.us> Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Cc: Ron Mercer <ron.mercer@qlogic.com> Cc: linux-driver@qlogic.com Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 7月, 2012 1 次提交
-
-
由 Yuval Mintz 提交于
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Cc: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 15 4月, 2012 1 次提交
-
-
由 Masanari Iida 提交于
Correct spelling typo within drivers/net. Signed-off-by: NMasanari Iida <standby24x7@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 2月, 2012 4 次提交
-
-
由 Jitendra Kalsaria 提交于
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jitendra Kalsaria 提交于
Driver was leaking memory when page allocation failures occurs. Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jitendra Kalsaria 提交于
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jitendra Kalsaria 提交于
we have copied skb into addr(page), skb->data doesn't contain ip header information. Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 2月, 2012 1 次提交
-
-
由 Joe Perches 提交于
alloc failures use dump_stack so emitting an additional out-of-memory message is an unnecessary duplication. Remove the allocation failure messages. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 09 12月, 2011 1 次提交
-
-
由 Jiri Pirko 提交于
Let caller know the result of adding/removing vlan id to/from vlan filter. In some drivers I make those functions to just return 0. But in those where there is able to see if hw setup went correctly, return value is set appropriately. Signed-off-by: NJiri Pirko <jpirko@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 11月, 2011 1 次提交
-
-
When transmiting a fragmented skb, qlge fills a descriptor with the fragment addresses, after DMA-mapping them. If there are more than eight fragments, it will use the eighth descriptor as a pointer to an external list. After mapping this external list, called OAL to a structure containing more descriptors, it fills it with the extra fragments. However, considering that systems with pages larger than 8KiB would have less than 8 fragments, which was true before commit a715dea3, it defined a macro for the OAL size as 0 in those cases. Now, if a skb with more than 8 fragments (counting skb->data as one fragment), this would start overwriting the list of addresses already mapped and would make the driver fail to properly unmap the right addresses on architectures with pages larger than 8KiB. Besides that, the list of mappings was one size too small, since it must have a mapping for the maxinum number of skb fragments plus one for skb->data and another for the OAL. So, even on architectures with page sizes 4KiB and 8KiB, a skb with the maximum number of fragments would make the driver overwrite its counter for the number of mappings, which, again, would make it fail to unmap the mapped DMA addresses. Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 17 11月, 2011 1 次提交
-
-
由 Michał Mirosław 提交于
v2: add couple missing conversions in drivers split unexporting netdev_fix_features() implemented %pNF convert sock::sk_route_(no?)caps Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 09 11月, 2011 1 次提交
-
-
由 Rick Jones 提交于
Per the mention made by Ben Hutchings that strlcpy is now the preferred string copy routine for a .get_drvinfo routine, do a bit of floor sweeping and convert some of the as-yet unconverted ethernet drivers to it. Signed-off-by: NRick Jones <rick.jones2@hp.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 19 10月, 2011 1 次提交
-
-
由 Eric Dumazet 提交于
To ease skb->truesize sanitization, its better to be able to localize all references to skb frags size. Define accessors : skb_frag_size() to fetch frag size, and skb_frag_size_{set|add|sub}() to manipulate it. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 07 10月, 2011 1 次提交
-
-
由 Ian Campbell 提交于
When I converted some drivers from pci_map_page to skb_frag_dma_map I neglected to convert PCI_DMA_xDEVICE into DMA_x_DEVICE and pci_dma_mapping_error into dma_mapping_error. Signed-off-by: NIan Campbell <ian.campbell@citrix.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 16 9月, 2011 1 次提交
-
-
由 Ian Campbell 提交于
Signed-off-by: NIan Campbell <ian.campbell@citrix.com> Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Cc: Ron Mercer <ron.mercer@qlogic.com> Cc: linux-driver@qlogic.com Cc: netdev@vger.kernel.org Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 18 8月, 2011 1 次提交
-
-
由 Jiri Pirko 提交于
replace it by ndo_set_rx_mode Signed-off-by: NJiri Pirko <jpirko@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 11 8月, 2011 1 次提交
-
-
由 Jeff Kirsher 提交于
Moves the QLogic drivers into drivers/net/ethernet/qlogic/ and the necessary Kconfig and Makefile changes. CC: Ron Mercer <ron.mercer@qlogic.com> CC: Amit Kumar Salecha <amit.salecha@qlogic.com> CC: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
-