Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TX queue was being stopped at beginning of send path instead
of at the end when last descriptor is used.
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enabling RX cut-thru mode yields better performance as received frames
start getting written to memory before a whole frame is received.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Increase the number of outstanding read and write AXI transactions from 1
to 8 for better performance.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix intermittent hangs in xgmac_rx_refill. If a ring buffer entry already
had an skb allocated, then xgmac_rx_refill would get stuck in a loop. This
can happen on a rx error when we just leave the skb allocated to the entry.

[ 7884.510000] INFO: rcu_preempt detected stall on CPU 0 (t=727315 jiffies)
[ 7884.510000] [<c0010a59>] (unwind_backtrace+0x1/0x98) from [<c006fd93>] (__rcu_pending+0x11b/0x2c4)
[ 7884.510000] [<c006fd93>] (__rcu_pending+0x11b/0x2c4) from [<c0070b95>] (rcu_check_callbacks+0xed/0x1a8)
[ 7884.510000] [<c0070b95>] (rcu_check_callbacks+0xed/0x1a8) from [<c0036abb>] (update_process_times+0x2b/0x48)
[ 7884.510000] [<c0036abb>] (update_process_times+0x2b/0x48) from [<c004e8fd>] (tick_sched_timer+0x51/0x94)
[ 7884.510000] [<c004e8fd>] (tick_sched_timer+0x51/0x94) from [<c0045527>] (__run_hrtimer+0x4f/0x1e8)
[ 7884.510000] [<c0045527>] (__run_hrtimer+0x4f/0x1e8) from [<c0046003>] (hrtimer_interrupt+0xd7/0x1e4)
[ 7884.510000] [<c0046003>] (hrtimer_interrupt+0xd7/0x1e4) from [<c00101d3>] (twd_handler+0x17/0x24)
[ 7884.510000] [<c00101d3>] (twd_handler+0x17/0x24) from [<c006be39>] (handle_percpu_devid_irq+0x59/0x114)
[ 7884.510000] [<c006be39>] (handle_percpu_devid_irq+0x59/0x114) from [<c0069aab>] (generic_handle_irq+0x17/0x2c)
[ 7884.510000] [<c0069aab>] (generic_handle_irq+0x17/0x2c) from [<c000cc8d>] (handle_IRQ+0x35/0x7c)
[ 7884.510000] [<c000cc8d>] (handle_IRQ+0x35/0x7c) from [<c033b153>] (__irq_svc+0x33/0xb8)
[ 7884.510000] [<c033b153>] (__irq_svc+0x33/0xb8) from [<c0244b06>] (xgmac_rx_refill+0x3a/0x140)
[ 7884.510000] [<c0244b06>] (xgmac_rx_refill+0x3a/0x140) from [<c02458ed>] (xgmac_poll+0x265/0x3bc)
[ 7884.510000] [<c02458ed>] (xgmac_poll+0x265/0x3bc) from [<c029fcbf>] (net_rx_action+0xc3/0x200)
[ 7884.510000] [<c029fcbf>] (net_rx_action+0xc3/0x200) from [<c0030cab>] (__do_softirq+0xa3/0x1bc)
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix net tx watchdog timeout recovery. The descriptor ring was reset,
but the DMA engine was not reset to the beginning of the ring.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set by the driver on packet recieve.
eth_type_trans already sets skb->dev to the proper value and it is not
referenced anywhere else in the dirver, thus making its setting unnecessary.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set during ring init and skb alloc in rx.  It is
already being set to the proper value when eth_type_trans is called on packet
receive, and the skb->dev is not referenced anywhere else in the code.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set by the driver's skb alloc routine (which is
called in init and during rx).  It is already being set to the proper value when
eth_type_trans is called on packet receive, and the skb->dev is not referenced
anywhere else in the code.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set during ring init and skb alloc in rx.  It is
already being set to the proper value when eth_type_trans is called on packet
receive, and the skb->dev is not referenced anywhere else in the code.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set by the driver on packet recieve.
eth_type_trans already sets skb->dev to the proper value and it is not
referenced anywhere else in the dirver, thus making its setting unnecessary.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Cc: linux-driver@qlogic.com
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set before calling eth_type_trans.
eth_type_trans already sets skb->dev to the proper value, thus making this
unnecessary.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: linux-driver@qlogic.com
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set during ring init.  It is already being set
to the proper value when eth_type_trans is called on packet receive, and the
skb->dev is not referenced anywhere else in the code.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set before calling eth_type_trans.
eth_type_trans already sets skb->dev to the proper value, thus making this
unnecessary.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set by the driver on packet recieve.
eth_type_trans already sets skb->dev to the proper value and it is not
referenced anywhere else in the dirver, thus making its setting unnecessary.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set after calling eth_type_trans.
eth_type_trans already sets skb->dev to the proper value, thus making this
unnecessary.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Roopa Prabhu <roprabhu@cisco.com>
Cc: Neel Patel <neepatel@cisco.com>
Cc: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set during ring init.  It is already being set
to the proper value when eth_type_trans is called on packet receive, and the
skb->dev is not referenced anywhere else in the code.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

URLs to neterion.com and s2io.com no longer resolve.  Remove all references to
these URLs in the driver source and documentation.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert doxygen (or similar) formatted comments to kernel-doc or
unformatted comment.  Delete a few that are content-free.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches.  Delete
a few that are content-free.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Macro spin_event_timeout() was designed for simple polling of hardware
registers with a timeout, so use it when we poll the MIIMIND register.
This allows us to return an error code instead of polling indefinitely.

Note that PHY_INIT_TIMEOUT is a count of loop iterations, so we can't use
it for spin_event_timeout(), which asks for microseconds.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

as the manual of module_pci_driver says that
it can be used when the init and exit functions of
the module does nothing but the pci_register_driver
and pci_unregister_driver.

use it for rdc's r6040 driver, as the init and exit
paths does as above, and also this reduces a little
amount of code.
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Acked-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

l4_rxhash is set on skb when rxhash is obtained from canonical 4-tuple
over transport ports/addresses.

We can set skb->l4_rxhash for all incoming TCP packets on bnx2x for
free, as cqe status contains a hash type information.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For RTL8111G, the settings of phy and firmware are replaced with
ocp functions. r8168g_mdio_{write / read} redirects the relative
settings to suitable ocp functions. A per-device variable is needed
to evaluate the real address of ocp functions.
rtl_writephy(tp, 0x1f, xxxx) is dedicated to keeping said variable
up-to-date.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>

Twelve functions can fail silently. Now they have a chance to complain.

Macro and pasting abuse has been kept at a level where tags and
friends should not be hurt.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

Further changes need more context down in the call stack.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>

ETH_P_IP is host Endian, skb->protocol is big Endian, when
compare them, we should change ETH_P_IP from host endian
to big endian, htons, not ntohs.

CC: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Acked-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Re-enable interrupts if it is not our interrupt
Signed-off-by: NMirko Lindner <mlindner@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the Optima EEE chipset.
Signed-off-by: NMirko Lindner <mlindner@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

OFF carrier state is setup in probe() open() and suspend() functions.
The carrier ON state is managed in macb_handle_link_change().
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The drop action is implemented by allocating a QP and keeping it in a reset state
such that the HW drops any packets which are steered to that QP. When a drop action
is requested, we attach the relevant flow to that QP.
Sign-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the ethtool APIs for attaching L2/L3/L4 based flow steering
rules to the netdevice RX rings. Added set_rxnfc callback and enhanced
the existing get_rxnfc callback.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device managed flow steering API has three promiscuous modes:

1. Uplink - captures all the packets that arrive to the port.
2. Allmulti - captures all multicast packets arriving to the port.
3. Function port - for future use, this mode is not implemented yet.

Use these modes with the flow_attach and flow_detach firmware commands
according to the promiscuous state of the netdevice.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As with other device resources, the resource tracker is needed for supporting
device managed flow steering rules under SRIOV: make sure virtual functions
delete only rules created by them, and clean all rules attached by a crashed VF.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver is modified to support three operation modes.

If supported by firmware use the device managed flow steering
API, that which we call device managed steering mode. Else, if
the firmware supports the B0 steering mode use it, and finally,
if none of the above, use the A0 steering mode.

When the steering mode is device managed, the code is modified
such that L2 based rules set by the mlx4_en driver for Ethernet
unicast and multicast, and the IB stack multicast attach calls
done through the mlx4_ib driver are all routed to use the device
managed API.

When attaching rule using device managed flow steering API,
the firmware returns a 64 bit registration id, which is to be
provided during detach.

Currently the firmware is always programmed during HCA initialization
to use standard L2 hashing. Future work should be done to allow
configuring the flow-steering hash function with common, non
proprietary means.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for firmware commands to attach/detach a new device managed
steering mode. Such network steering rules allow the user to provide an
L2/L3/L4 flow specification to the firmware and have the device to steer
traffic that matches that specification to the provided QP.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of checking the firmware supported steering mode in various
places in the code, add a dedicated field in the mlx4 device capabilities
structure which is written once during the initialization flow and read
across the code.

This also set the grounds for add new steering modes. Currently two modes
are supported, and are named after the ConnectX HW versions A0 and B0.

A0 steering uses mac_index, vlan_index and priority to steer traffic
into pre-defined range of QPs.

B0 steering uses Ethernet L2 hashing rules and is enabled only
if the firmware supports both unicast and multicast B0 steering,

The current steering modes are relevant for Ethernet traffic only,
such that Infiniband steering remains untouched.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>