The convention is to prefix symbols exported from the USB HCD core with
"usb_hcd".  This change makes unmap_urb_setup_for_dma() and
unmap_urb_for_dma() consistent with that.
Signed-off-by: NRobert Morell <rmorell@nvidia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In create_companion_file() there is a bogus assignemt to i created for
the express purpose of avoiding an ignored return value warning.

With pre-release GCC-4.6, this causes a 'set but not used' warning.

Kick the problem further down the road by just returning i.  All the
callers of create_companion_file() ignore its return value, so all is
good:

o No warnings are issued.

o We still subvert the desires of the authors of device_create_file()
  by ignorning error conditions.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

With pre-release GCC-4.6, we get a 'set but not used' warning when
EHCI_URB_TRACE is not set because we set the qtd variable without
using it.

Rearrange the statements so that we only set qtd if it will be used.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The vdbg macro is not used anywhere so it can be removed.

With pre-release GCC-4.6, there are several complaints of variables
that are 'set but not used' caused by the ehci_vdbg() macro expanding
to something that does not contain any of its arguments.  We can quiet
this warning by rewriting ehci_vdbg() as a variadic static inline that
does nothing.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The pre-release GCC-4.6 now correctly flags this code as dead.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch moves the AMD PLL quirk code in OHCI/EHCI driver to pci-quirks.c,
and exports the functions to be used by xHCI driver later.

AMD PLL quirk disable the optional PM feature inside specific
SB700/SB800/Hudson-2/3 platforms under the following conditions:

1. If an isochronous device is connected to OHCI/EHCI/xHCI port and is active;
2. Optional PM feature that powers down the internal Bus PLL when the link is
   in low power state is enabled.

Without AMD PLL quirk, USB isochronous stream may stutter or have breaks
occasionally, which greatly impair the performance of audio/video streams.

Currently AMD PLL quirk is implemented in OHCI and EHCI driver, and will be
added to xHCI driver too. They are doing similar things actually, so move
the quirk code to pci-quirks.c, which has several advantages:

1. Remove duplicate defines and functions in OHCI/EHCI (and xHCI) driver and
   make them cleaner;
2. AMD chipset information will be probed only once and then stored.
   Currently they're probed during every OHCI/EHCI initialization, move
   the detect code to pci-quirks.c saves the repeat detect cost;
3. Build up synchronization among OHCI/EHCI/xHCI driver. In current
   code, every host controller enable/disable PLL only according to
   its own status, and may enable PLL while there is still isoc transfer on
   other HCs. Move the quirk to pci-quirks.c prevents this issue.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The below patch fixes a typo "diable" to "disable" and also fixes another typo in a comment.
Please let me know if this is correct or not.
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Current code doesn't really enable the usb clocks so if they're disabled
when booting linux, the kernel/machine will hang as soon as someone is trying
to read a usb register
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

flush_scheduled_work() is being deprecated.  Directly flush or cancel
work items instead.

* u_ether, isp1301_omap, speedtch conversions are straight-forward.

* ochi-hcd should only flush when quirk_nec() is true as otherwise the
  work wouldn't have been initialized.

* In oti6858, cancel_delayed_work() + flush_scheduled_work() ->
  cancel_delayed_work_sync().
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Duncan Sands <duncan.sands@free.fr>
Cc: linux-usb@vger.kernel.org

In order to read/write to the i.MX OTG viewport register it is necessary to setup
the PORTSCx register first.

By default i.MX OTG port is configured for USB serial PHY. In order to use a ULPI PHY
the PORTSCx register needs to be configured properly.

commit 724c8525 (USB: ehci/mxc: compile fix) placed the PORTSC setup after the OTG
viewport is accessed and this causes ULPI read/write to fail.

Revert the PORTSC setup order.

Tested on a MX31PDK board with a ISP1504 transceiver:

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
mxc-ehci mxc-ehci.0: initializing i.MX USB Controller
ULPI transceiver vendor/product ID 0x04cc/0x1504
Found NXP ISP1504 ULPI transceiver.
ULPI integrity check: passed.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The TLL channel enable code searches for the wrong mask, and
could end up enabling the wrong port. Fix this.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is the ohci-omap3 driver, not ehci-omap. Correct this
obvious typo.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Enable runtime PM and mark no_callbacks flag.  OTG device, parent of
HCD takes care of putting hardware into low power mode.  Adjust port
power wakeup flags during system suspend and resume.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for EHCI compliant HSUSB Host controller found
on MSM chips.  The root hub has a single port and TT is built into it.
This driver depends on OTG driver for PHY initialization, clock
management and powering up VBUS.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When ASPM PM Feature is enabled on UMI link, devices that use ISOC stream of
data transfer may be exposed to longer latency causing less than optimal per-
formance of the device. The longer latencies are normal and are due to link
wake time coming out of low power state which happens frequently to save
power when the link is not active.
The following code will make exception for certain features of ASPM to be by
passed and keep the logic normal state only when the ISOC device is connected
and active. This change will allow the device to run at optimal performance
yet minimize the impact on overall power savings.
Signed-off-by: NAlex He <alex.he@amd.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixed coding style issues (delete trailing whitespaces, break
long line)
Signed-off-by: NTobias Ollmann <tobias.ollmann@gmx.at>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Annotate whci_hcd_id_table as '__used' to fix following warning:

  CC      drivers/usb/host/whci/hcd.o
drivers/usb/host/whci/hcd.c:359: warning: ‘whci_hcd_id_table’ defined but not used
Signed-off-by: NNamhyung Kim <namhyung@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix two bugs with the port array setup.

The first bug will only show up with broken xHCI hosts with Extended
Capabilities registers that have duplicate port speed entries for the same
port.  The idea with the original code was to set the port_array entry to
-1 if the duplicate port speed entry said the port was a different speed
than the original port speed entry.  That would mean that later, the port
would not be exposed to the USB core. Unfortunately, I forgot a continue
statement, and the port_array entry would just be overwritten in the next
line.

The second bug would happen if there are conflicting port speed registers
(so that some entry in port_array is -1), or one of the hardware port
registers was not described in the port speed registers (so that some
entry in port_array is 0).  The code that sets up the usb2_ports array
would accidentally claim those ports.  That wouldn't really cause any
user-visible issues, but it is a bug.

This patch should go into the stable trees that have the port array and
USB 3.0 port disabling prevention patches.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org

Several of the EHCI glue drivers either predate or were merged in the
same timeframe as API changes at the USB core level, resulting in some
missing endpoint_reset and clear_tt_buffer_complete callbacks.

This fixes up all of ehci-atmel, mxc, w90x900, and xilinx-of to tie in
the new helpers, which brings them in line with everyone else.
Reported-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Hi,

The [vk][cmz]alloc(_node) family of functions return void pointers which
it's completely unnecessary/pointless to cast to other pointer types since
that happens implicitly.

This patch removes such casts from drivers/usb/
Signed-off-by: NJesper Juhl <jj@chaosbits.net>

Update the ehci-omap glue layer to support the controller in the
OMAP4. Major differences from OMAP3 is that the OMAP4 has per-port
clocking, and supports ULPI output clocking mode. The old input
clocking mode is not supported.

Also, there are only 2 externally available ports as against 3
in the OMAP3. The third port is internally tied off and should
not be used.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>

Introduce helper functions to test port mode. These checks are
performed in several places in the driver, and these helpers
improve readability.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>

Use the recently updated aliases to get functional clocks needed by
the driver. This allows the driver to acquire OMAP4-specific clocks
without having to use different clock names for OMAP3 and OMAP4.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>

Introduce the CONFIG_USB_EHCI_HCD_OMAP option to select
EHCI support on OMAP3 and later chips. This scales better
than having a long line of dependencies for each new OMAP
with EHCI support.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>

Make the TLL channel count a parameter instead of a hardcoded
value. This allows us to be flexible with future OMAP revisions
which could have a different number of channels.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>

Rename usbhost2_120m_fck to usbhost_hs_fck and usbhost1_48m_fck
to usbhost_fs_fck, to better reflect the clocks' functionalities.

In OMAP4, the frequencies for the corresponding clocks are not
necessarily the same as with OMAP3, however the functionalities
are.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>

Tested on MacBookAir3,1.  Without this, we get EPROTO errors when
fetching device config descriptors.
Signed-off-by: NBrian Tarricone <brian@tarricone.org>
Reported-by: NBenoit Gschwind <gschwind@gnu-log.net>
Tested-by: NEdgar Hucek <gimli@dark-green.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The CNS3XXX SOC has include USB EHCI and OHCI compatible controllers.
This patch adds the necessary glue logic to allow ehci-hcd and ohci-hcd
drivers to work on CNS3XXX

The EHCI and OHCI controllers share a common clock control and reset
bit, therefore additional check for the timming of enabling and disabling
is required. The USB bit of PLL Power Down Control is also shared by OTG,
24MHzUART clock, Crypto clock, PCIe reference clock, and Clock Scale
Generator. Therefore we only ensure it is enabled, while not disabling it.
Signed-off-by: NMac Lin <mkl0301@gmail.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

The ehci-sh driver was missing tie-ins for endpoint_reset and
clear_tt_buffer_complete, add them in.
Reported-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

We can't use the generic usb_hcd_platform_shutdown helper on account of
the fact we don't stash the hcd pointer in the driver data, so we provide
our own shutdown handler.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Disabling SuperSpeed ports is a Very Bad Thing (TM).  It disables
SuperSpeed terminations, which means that devices will never connect at
SuperSpeed on that port.  For USB 2.0/1.1 ports, disabling the port meant
that the USB core could always get a connect status change later.  That's
not true with USB 3.0 ports.

Do not let the USB core disable SuperSpeed ports.  We can't rely on the
device speed in the port status registers, since that isn't valid until
there's a USB device connected to the port.  Instead, we use the port
speed array that's created from the Extended Capabilities registers.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NDon Zickus <dzickus@redhat.com>
Cc: stable@kernel.org

An xHCI host controller contains USB 2.0 and USB 3.0 ports, which can
occur in any order in the PORTSC registers.  We cannot read the port speed
bits in the PORTSC registers at init time to determine the port speed,
since those bits are only valid when a USB device is plugged into the
port.

Instead, we read the "Supported Protocol Capability" registers in the xHC
Extended Capabilities space.  Those describe the protocol, port offset in
the PORTSC registers, and port count.  We use those registers to create
two arrays of pointers to the PORTSC registers, one for USB 3.0 ports, and
another for USB 2.0 ports.  A third array keeps track of the port protocol
major revision, and is indexed with the internal xHCI port number.

This commit is a bit big, but it should be queued for stable because the "Don't
let the USB core disable SuperSpeed ports" patch depends on it.  There is no
other way to determine which ports are SuperSpeed ports without this patch.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NDon Zickus <dzickus@redhat.com>
Cc: stable@kernel.org

We have been having problems with the USB-IF Gold Tree tests when plugging
and unplugging devices from the tree. I have seen that the reset-device
and configure-endpoint commands, which are invoked from
xhci_discover_or_reset_device() and xhci_configure_endpoint(), will sometimes
time out.

After much debugging, I determined that the commands themselves do not actually
time out, but rather their completion events do not get delivered to the right
place.

This happens when the command ring has just wrapped around, and it's enqueue
pointer is left pointing to the link TRB. xhci_discover_or_reset_device() and
xhci_configure_endpoint() use the enqueue pointer directly as their command
TRB pointer, without checking whether it's pointing to the link TRB.

When the completion event arrives, if the command TRB is pointing to the link
TRB, the check against the command ring dequeue pointer in
handle_cmd_in_cmd_wait_list() fails, so the completion inside the command does
not get signaled.

The patch below fixes the timeout problem for me.

This should be queued for the 2.6.35 and 2.6.36 stable trees.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org

This patch adds support for the EHCI IP block present on the Intel
CE4100.
Signed-off-by: NDirk Brandewie <dirk.brandewie@gmail.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The big kernel lock has been removed from all these files at some point,
leaving only the #include.

Remove this too as a cleanup.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for ehci and ohci controller in the SPEAr platform.

Changes since V2:
added clear_tt_buffer_complete in ehci_spear_hc_driver
Signed-off-by: NDeepak Sikri <deepak.sikri@st.com>
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1435) fixes an obscure and unlikely race in ehci-hcd.
When an async URB is unlinked, the corresponding QH is removed from
the async list.  If the QH's endpoint is then disabled while the URB
is being given back, ehci_endpoint_disable() won't find the QH on the
async list, causing it to believe that the QH has been lost.  This
will lead to a memory leak at best and quite possibly to an oops.

The solution is to trust usbcore not to lose track of endpoints.  If
the QH isn't on the async list then it doesn't need to be taken off
the list, but the driver should still wait for the QH to become IDLE
before disabling it.

In theory this fixes Bugzilla #20182.  In fact the race is so rare
that it's not possible to tell whether the bug is still present.
However, adding delays and making other changes to force the race
seems to show that the patch works.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
CC: David Brownell <david-b@pacbell.net>
CC: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix section mismatch warning by using "__devinit" annotation for isp1362_probe.

WARNING: drivers/usb/host/isp1362-hcd.o(.data+0x0): Section mismatch in reference from the variable isp1362_driver to the function .init.text:isp1362_probe()
The variable isp1362_driver references
the function __init isp1362_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On AMD SB700/SB800/Hudson-2/3 platforms, USB EHCI controller may read/write
to memory space not allocated to USB controller if there is longer than
normal latency on DMA read encountered. In this condition the exposure will
be encountered only if the driver has following format of Periodic Frame
List link pointer structure:

For any idle periodic schedule, the Frame List link pointers that have the
T-bit set to 1 intending to terminate the use of frame list link pointer
as a physical memory pointer.

Idle periodic schedule Frame List Link pointer shoule be in the following
format to avoid the issue:

Frame list link pointer should be always contains a valid pointer to a
inactive QHead with T-bit set to 0.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>