drivers: fix comment typo diable -> disable.

The below patch fixes a typo "diable" to "disable" and also fixes another typo in a comment.
Please let me know if this is correct or not.
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

drivers/isdn/mISDN/dsp_cmx.c

@@ -112,7 +112,7 @@
  * Disable rx-data:
  * If cmx is realized in hardware, rx data will be disabled if requested by
  * the upper layer. If dtmf decoding is done by software and enabled, rx data
- * will not be diabled but blocked to the upper layer.
+ * will not be disabled but blocked to the upper layer.
  *
  * HFC conference engine:
  * If it is possible to realize all features using hardware, hardware will be

drivers/scsi/lpfc/lpfc_init.c

@@ -7661,7 +7661,7 @@ lpfc_pci_remove_one_s3(struct pci_dev *pdev)
 	 * the HBA.
 	 */
 
-	/* HBA interrupt will be diabled after this call */
+	/* HBA interrupt will be disabled after this call */
 	lpfc_sli_hba_down(phba);
 	/* Stop kthread signal shall trigger work_done one more time */
 	kthread_stop(phba->worker_thread);

drivers/usb/gadget/langwell_udc.c

@@ -3063,7 +3063,7 @@ static void langwell_udc_remove(struct pci_dev *pdev)
 
 	kfree(dev->ep);
 
-	/* diable IRQ handler */
+	/* disable IRQ handler */
 	if (dev->got_irq)
 		free_irq(pdev->irq, dev);
 
@@ -3383,7 +3383,7 @@ static int langwell_udc_suspend(struct pci_dev *pdev, pm_message_t state)
 	/* disable interrupt and set controller to stop state */
 	langwell_udc_stop(dev);
 
-	/* diable IRQ handler */
+	/* disable IRQ handler */
 	if (dev->got_irq)
 		free_irq(pdev->irq, dev);
 	dev->got_irq = 0;

drivers/usb/host/fhci-hcd.c

@@ -98,13 +98,13 @@ void fhci_usb_enable_interrupt(struct fhci_usb *usb)
 	usb->intr_nesting_cnt--;
 }
 
-/* diable the usb interrupt */
+/* disable the usb interrupt */
 void fhci_usb_disable_interrupt(struct fhci_usb *usb)
 {
 	struct fhci_hcd *fhci = usb->fhci;
 
 	if (usb->intr_nesting_cnt == 0) {
-		/* diable the timer interrupt */
+		/* disable the timer interrupt */
 		disable_irq_nosync(fhci->timer->irq);
 
 		/* disable the usb interrupt */

drivers/usb/host/fhci-tds.c

@@ -271,8 +271,8 @@ void fhci_init_ep_registers(struct fhci_usb *usb, struct endpoint *ep,
 
 /*
  * Collect the submitted frames and inform the application about them
- * It is also prepearing the TDs for new frames. If the Tx interrupts
- * are diabled, the application should call that routine to get
+ * It is also preparing the TDs for new frames. If the Tx interrupts
+ * are disabled, the application should call that routine to get
  * confirmation about the submitted frames. Otherwise, the routine is
  * called frome the interrupt service routine during the Tx interrupt.
  * In that case the application is informed by calling the application