Our bootloader now supports ATAGS_MEM
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NStefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NJaya Kumar <jayakumar.lkml@gmail.com>
Cc: Andre Puschmann <andre.puschmann@imms.de>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

fbi->state change shall really be protected by fbi->ctrlr_lock, where
the change is sheltered. There is a possibility that pxafb_smart_thread
will start update the LCD panel when fbi->state == C_ENABLE, while
all other initialization isn't done.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Some smart panel requires a delay between command sequences, while PXA
LCD controller didn't provide such one, let's emulate this by software.

A software delay marker can be inserted into the command sequence, once
pxafb_smart_queue() detects this, it flushes the previous commands and
delay for a specified number of milliseconds.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

For smart panels (LCD panel with internal framebuffer), the following
LCCR3 register bits have different meanings than the parallel one:

  LCCR3_PCP - controls the L_PCLK_WR polarity
  LCCR3_HSP - controls the L_LCLK_A0 polarity
  LCCR3_VSP - controls the L_FCLK_RD polarity

To keep minimum change to the original parallel timing, the .lcd_conn
flags and 'pxafb_mode_info.sync' are re-used to reflect this:

  LCD_PCLK_EDGE_{RISE,FALL} - configures LCCR3_PCP
  sync & FB_SYNC_{HOR,VERT}_HIGH_ACT - configures LCCR3_{HSP,VSP}
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Group smart panel related code in a more compact fasion, avoid abused
usage of #ifdef .. #endif.

Also fix the incorrect condition in pxafb_smart_init() to decide if it
is a smart panel or not. (should be '&' instead of '|')
Signed-off-by: NEric Miao <eric.miao@marvell.com>

platform should now initialize the pin usage for the LCD controller
to correctly work.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Ian Molton <spyro@f2s.com>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Juergen Schindele <linux@schindele.name>
Acked-by: NStefan Schmidt <stefan@datenfreihafen.org>
Acked-by: NMarc Zyngier <maz@misterjones.org>
Acked-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NJaya Kumar <jayakumar.lkml@gmail.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

This patch adds HP iPAQ h5000's (h5400, h5500) basic definitions.

Kernel will able to boot, work via serial console, mount filesystems
placed on flashes and run USB gadgets (g_ether by default).

Other device drivers (frame buffer, LCD, touchscreen, backlight,
bluetooth, w1/battery, ...) are depend on SAMCOP and MediaQ
SoCs/MFDs, drivers to which will be submitted too, after massive
cleanups.

This machine will be used as "real user" for these new drivers.

This is an updated version of the patch, which contains fixes proposed on
linux-arm-kernel mailing list.
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NMilan Plzik <milan.plzik@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Add mapping for system ROM using physmap-flash mapping.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Add mapping for system ROM using physmap-flash mapping.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Add mapping for system ROM using physmap-flash mapping.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Add mapping for system ROM using physmap-flash mapping.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Add platform data necessary to support tmiofb on tosa.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Take advantage of the newly created wm97xx battery driver
and remove useless code in mioa701 board code. Add also the
ac connection detect capability after the matching gpio was
discovered.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

The charger enable gpio is straight (1 means draw from USB
Vbus, 0 mean do not draw). The USB Vbus sensing is inverted
(1 means no Vbus voltage sensed, 0 means Vbus voltage
present).
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Change the halt and reboot method from gpio based to "jump
to ROM IPL beginning". This gives control back to IPL, which
without PowerOn key pressed, will put the device into deep
sleep until PowerOn is pressed for 1 second.

But this has the benefit of keeping the RTC registers across
reboots, which is good for OS change.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Add GPIO configuration and platform specific declarations
to make Mitac Mio A701 camera chip work. The chip is a
Micron MT9M111 CMOS sensor, based on PXA QIF interface and
I2C bus for sensor control.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Since mioa701 board has migrated to the mfp architecture,
low power gpio setup is now correctly handled even when gpio
led driver is not loaded, and leds and vibrator don't stay
activated in suspend mode (especially vibrator).

Remove the not needed anymore dependency.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Add IO memory and IRQ ressources for pxa based SoC to be
able to use the new rtc-pxa driver.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

This patch implements Eric Miao's idea to detect the correct value of
sdram_rows by inspecting the MDCNFG register settings.
It is only tested on two pxa27x devices with 64MB RAM (magician and
hx4700) so far.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Following the removal of the "->policy" usage for PXA255 in patch
459fc208 (cpufreq: remove
policy->governor setting in drivers initialization), this patch
introduces an option (called "pxa255_turbo_table") to select either
the "run" or "turbo" frequency table.

It also cures the runtime warning that was printed each time the
frequency was changed.

Got rid of all references to CPUFREQ_POLICY_* for pxa255, and sticked
with the run/turbo thing.

Tested on an Arcom/Eurotech Viper.
Signed-off-by: NMarc Zyngier <maz@misterjones.org>
Acked-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

instead of holding them as static pointers.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

This symbol is required by locomo backlight driver, exporting this
allows the driver to be built as a module.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

GPIO3/GPIO4 are a bit special on pxa27x, since it depends on PCFR/PI2C_EN
bit, add their definitions here with comments.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Acked-by: NStefan Schmidt <stefan@datenfreihafen.org>

PXA935 has changed its implementor ID from Intel to Marvell, this
patch modifies arch/arm/boot/compressed/head.S and proc-xsc3.S to
support a smooth bootup.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

Let's put these devices into a central place even if they are now
processor specific, as they might be re-used in later processors.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

for the reference of __REG() within <mach/hardware.h>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

The optimal change would be to move the AC97 register definitions into
the AC97 driver, unfortunately, the registers are shared between several
files. Move them into a dedicated regs-ac97.h first.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

There two are internal registers that are used to control the power
management of the Internal Memory (i.e. Internal SRAM). They are
referenced nowhere and removed here to simplify pxa-regs.h a bit.
Signed-off-by: NEric Miao <eric.miao@marvell.com>