The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.

This patch:
  - Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
    NETIF_F_ALL_CSUM is being used as a mask).
  - Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
    use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SCTP checksum is really a CRC and is very different from the
standards 1's complement checksum that serves as the checksum
for IP protocols. This offload interface is also very different.
Rename NETIF_F_SCTP_CSUM to NETIF_F_SCTP_CRC to highlight these
differences. The term CSUM should be reserved in the stack to refer
to the standard 1's complement IP checksum.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the introduction of 82574 support in e1000e, the driver has worked
on the assumption that msi-x interrupt generation is automatically
disabled after each irq. As it turns out, this is not the case.
Currently, rx interrupts can fire multiple times before and during napi
processing. This can be a problem for users because frames that arrive
in a certain window (after adapter->clean_rx() but before
napi_complete_done() has cleared NAPI_STATE_SCHED) generate an interrupt
which does not lead to napi_schedule(). These frames sit in the rx queue
until another frame arrives (a tcp retransmit for example).

While the EIAC and CTRL_EXT registers are properly configured for irq
automask, the modification of IAM in e1000_configure_msix() is what
prevents automask from working as intended.

This patch removes that erroneous write and fixes interrupt rearming for
tx interrupts. It also clears IAME from CTRL_EXT. This is not strictly
necessary for operation of the driver but it is to avoid disruption from
potential programs that access the registers directly, like `ethregs -c`.
Reported-by: NFrank Steiner <steiner-reg@bio.ifi.lmu.de>
Signed-off-by: NBenjamin Poirier <bpoirier@suse.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In msi-x mode, there is no handler for the lsc interrupt so there is no
point in writing that to ics now that we always assume Other interrupts
are caused by lsc.
Reviewed-by: NJasna Hodzic <jhodzic@ucdavis.edu>
Signed-off-by: NBenjamin Poirier <bpoirier@suse.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Removes the ICR read in the other interrupt handler, uses EIAC to
autoclear the Other bit from ICR and IMS. This allows us to avoid
interference with Rx and Tx interrupts in the Other interrupt handler.

The information read from ICR is not needed. IMS is configured such that
the only interrupt cause that can trigger the Other interrupt is Link
Status Change.
Signed-off-by: NBenjamin Poirier <bpoirier@suse.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

msi-x interrupts are not shared so there's no need to check if the
interrupt was really from this adapter.
Signed-off-by: NBenjamin Poirier <bpoirier@suse.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously, the ethtool self-test gstrings/data arrays were accessed via
hardcoded indices, which made the code difficult to follow. This patch
replaces the hardcoded values with enum-based labels.
Signed-off-by: NJoe Schultz <jschultz@xes-inc.com>
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously, the PHY-specific code to get the cable length for the
I210 internal and related PHYs was reporting the cable length of a
single pair and reporting it as the min, max, and total cable length.
Update it so that all four pairs are checked so the true min, max,
and average cable lengths are reported.
Signed-off-by: NJoe Schultz <jschultz@xes-inc.com>
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is no reason to add the PHY address into the PCDL register address.
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The I210 internal PHY can be accessed just as well with the access
functions shared by 82580, I350, and I354 devices. A side effect of
relying on the common functions, is that I210 cable length support
is folded back into the common case which effectively reverts the
following commit:

    commit 59f30104
    Author: Carolyn Wyborny <carolyn.wyborny@intel.com>
    Date:   Wed Oct 10 04:42:59 2012 +0000

    igb: Update get cable length function for i210/i211

Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The function e1000e_up always returns 0.  As such we can convert it to a
void and just ignore the results.  This allows us to drop some code in a
couple spots as we no longer need to worry about non-zero return values.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Similar to ixgbe and i40e, initialize XPS on driver load so that we can
take advantage of this kernel feature.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make functions that should be static.  While we're at it, fix the function
header comment for fm10k_tlv_attr_nest_stop(), and update the copyright
header for fm10k_pf.h, fm10k_tlv.c and fm10k_tlv.h.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The function declaration does not need to be 'inline'd here.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch addresses two issues.

First is the fact that the fm10k_mbx_free_irq was assuming msix_entries was
valid and that will not always be the case.  As such we need to add a check
for if it is NULL.

Second is the fact that we weren't freeing the IRQ if the mailbox API
returned an error on trying to connect.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the q_vector allocation fails we should free the resources associated
with the MSI-X vector table.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Rather than wrapping fm10k_dcbnl.c and fm10k_debugfs.c support with
 #ifdef blocks, just conditionally include the .o files in the Makefile.
Also, since we're modifying it, update the copyright year on the
Makefile.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We haven't bumped the driver version in a while despite many fixes being
pulled in from the out-of-tree Sourceforge driver. Update the version to
match.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of using lowercase vlan, vid, or VID, always use VLAN or VLAN ID
in comments when referring to VLANs. The original driver code was
consistent, but recent patches have not been as consistent with this
naming scheme.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Improve code style by removing the unnecessary else block of an if
statement which immediately returns.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Avoid the use of CamelCase for some variable names that previously
slipped through review.
Reported-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the ether_addr_copy function instead of copying byte-by-byte in a
for-loop by hand.
Reported-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

i219-LM (3) is a LOM that will be available on systems with the
Lewisburg Platform Controller Hub (PCH) chipset from Intel.
This patch provides the initial support for the device.
Signed-off-by: NRaanan Avargil <raanan.avargil@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Clean up array_rd32 so that it uses igb_rd32 the same as rd32, per the
suggestion of Alexander Duyck, and use io_addr in more places, so that
we don't have the need to call E1000_REMOVED (which simply looks for a
null hw_addr) nearly as much.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Acked-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The combined effect of commits 6423fc34 ("igb: do not re-init SR-IOV
during probe") and ceee3450 ("igb: make sure SR-IOV init uses the
right number of queues") causes VFs no longer getting set up, leading
to NULL pointer dereferences due to the adapter's ->vf_data being NULL
while ->vfs_allocated_count is non-zero. The first commit not only
neglected the side effect of igb_sriov_reinit() that the second commit
tried to account for, but also that of setting IGB_FLAG_HAS_MSIX,
without which igb_enable_sriov() is effectively a no-op. Calling
igb_{,re}set_interrupt_capability() as done here seems to address this,
but I'm not sure whether this is better than sinply reverting the other
two commits.
Signed-off-by: NJan Beulich <jbeulich@suse.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to timing changes to the ME firmware in Skylake, this timer
needs to be increased to 300ms.
Signed-off-by: NRaanan Avargil <raanan.avargil@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes possible division by zero in receive
interrupt handler when working without adaptive interrupt
moderation.

The adaptive interrupt moderation mechanism is typically
disabled on jumbo MTUs.
Signed-off-by: NDmitry Fleytman <dmitry@daynix.com>
Signed-off-by: NLeonid Bloch <leonid@daynix.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJanusz Wolak <januszvdm@gmail.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

By using goto statement, we can achieve sharing the same exit path so
that code duplication could be minimized.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to historical reason, 'phy_data' has never been included in the
kernel doc. Fix it so that the requirement could be fulfilled.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The local variable 'ret' doesn't serve much purpose so we might as well
clean it up.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use 'That' to replace 'The' so that the comment would make sense.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The checking logic needed some clean-up work, so we rewrite it by
checking for break first. With that change in place, we can even move
the second check for goto statement outside of the loop.

As this is merely a cleanup, no functional change is involved. The
questionable 'tmp != 0xFF' is intentionally left alone.

Mark Rustad and Alexander Duyck contributed to this patch.

CC: Mark Rustad <mark.d.rustad@intel.com>
CC: Alex Duyck <aduyck@mirantis.com>
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i210 has two EEPROM access registers that are located in
non-standard offsets: EEARBC and EEMNGCTL. EEARBC was fixed previously
and EEMNGCTL should also be corrected.
Reported-by: NRoman Hodek <roman.aud@siemens.com>
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJanusz Wolak <januszvdm@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

I've got a startech thunderbolt dock someone loaned me, which among other
things, has the following device in it:

08:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03)

This hotplugs just fine (kernel 4.2.0 plus a patch or two here):

[  863.020315] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.2.18-k
[  863.020316] igb: Copyright (c) 2007-2014 Intel Corporation.
[  863.028657] igb 0000:08:00.0: enabling device (0000 -> 0002)
[  863.062089] igb 0000:08:00.0: added PHC on eth0
[  863.062090] igb 0000:08:00.0: Intel(R) Gigabit Ethernet Network Connection
[  863.062091] igb 0000:08:00.0: eth0: (PCIe:2.5Gb/s:Width x1) e8:ea:6a:00:1b:2a
[  863.062194] igb 0000:08:00.0: eth0: PBA No: 000200-000
[  863.062196] igb 0000:08:00.0: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s)
[  863.064889] igb 0000:08:00.0 enp8s0: renamed from eth0

But disconnecting it is another story:

[ 1002.807932] igb 0000:08:00.0: removed PHC on enp8s0
[ 1002.807944] igb 0000:08:00.0 enp8s0: PCIe link lost, device now detached
[ 1003.341141] ------------[ cut here ]------------
[ 1003.341148] WARNING: CPU: 0 PID: 199 at lib/iomap.c:43 bad_io_access+0x38/0x40()
[ 1003.341149] Bad IO access at port 0x0 ()
[ 1003.342767] Modules linked in: snd_usb_audio snd_usbmidi_lib snd_rawmidi igb dca firewire_ohci firewire_core crc_itu_t rfcomm ctr ccm arc4 iwlmvm mac80211 fuse xt_CHECKSUM ipt_MASQUERADE
nf_nat_masquerade_ipv4 tun ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 ipt_REJECT nf_reject_ipv4 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat
nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat
nf_conntrack iptable_mangle iptable_security iptable_raw iptable_filter bnep dm_mirror dm_region_hash dm_log dm_mod coretemp x86_pkg_temp_thermal intel_powerclamp kvm_intel snd_hda_codec_hdmi kvm
crct10dif_pclmul crc32_pclmul ghash_clmulni_intel drbg
[ 1003.342793]  ansi_cprng aesni_intel hp_wmi aes_x86_64 iTCO_wdt lrw iTCO_vendor_support ppdev gf128mul sparse_keymap glue_helper ablk_helper cryptd snd_hda_codec_realtek snd_hda_codec_generic
microcode snd_hda_intel uvcvideo iwlwifi snd_hda_codec videobuf2_vmalloc videobuf2_memops snd_hda_core videobuf2_core snd_hwdep btusb v4l2_common btrtl snd_seq btbcm btintel videodev cfg80211
snd_seq_device rtsx_pci_ms bluetooth pcspkr input_leds i2c_i801 media parport_pc memstick rfkill sg lpc_ich snd_pcm 8250_fintek parport joydev snd_timer snd soundcore hp_accel ie31200_edac
mei_me lis3lv02d edac_core input_polldev mei hp_wireless shpchp tpm_infineon sch_fq_codel nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables autofs4 xfs libcrc32c sd_mod sr_mod cdrom
rtsx_pci_sdmmc mmc_core crc32c_intel serio_raw rtsx_pci
[ 1003.342822]  nouveau ahci libahci mxm_wmi e1000e xhci_pci hwmon ptp drm_kms_helper pps_core xhci_hcd ttm wmi video ipv6
[ 1003.342839] CPU: 0 PID: 199 Comm: kworker/0:2 Not tainted 4.2.0-2.el7_UNSUPPORTED.x86_64 #1
[ 1003.342840] Hardware name: Hewlett-Packard HP ZBook 15 G2/2253, BIOS M70 Ver. 01.07 02/26/2015
[ 1003.342843] Workqueue: pciehp-3 pciehp_power_thread
[ 1003.342844]  ffffffff81a90655 ffff8804866d3b48 ffffffff8164763a 0000000000000000
[ 1003.342846]  ffff8804866d3b98 ffff8804866d3b88 ffffffff8107134a ffff8804866d3b88
[ 1003.342847]  ffff880486f46000 ffff88046c8a8000 ffff880486f46840 ffff88046c8a8098
[ 1003.342848] Call Trace:
[ 1003.342852]  [<ffffffff8164763a>] dump_stack+0x45/0x57
[ 1003.342855]  [<ffffffff8107134a>] warn_slowpath_common+0x8a/0xc0
[ 1003.342857]  [<ffffffff810713c6>] warn_slowpath_fmt+0x46/0x50
[ 1003.342859]  [<ffffffff8133719e>] ? pci_disable_msix+0x3e/0x50
[ 1003.342860]  [<ffffffff812f6328>] bad_io_access+0x38/0x40
[ 1003.342861]  [<ffffffff812f6567>] pci_iounmap+0x27/0x40
[ 1003.342865]  [<ffffffffa0b728d7>] igb_remove+0xc7/0x160 [igb]
[ 1003.342867]  [<ffffffff8132189f>] pci_device_remove+0x3f/0xc0
[ 1003.342869]  [<ffffffff81433426>] __device_release_driver+0x96/0x130
[ 1003.342870]  [<ffffffff814334e3>] device_release_driver+0x23/0x30
[ 1003.342871]  [<ffffffff8131b404>] pci_stop_bus_device+0x94/0xa0
[ 1003.342872]  [<ffffffff8131b3ad>] pci_stop_bus_device+0x3d/0xa0
[ 1003.342873]  [<ffffffff8131b3ad>] pci_stop_bus_device+0x3d/0xa0
[ 1003.342874]  [<ffffffff8131b516>] pci_stop_and_remove_bus_device+0x16/0x30
[ 1003.342876]  [<ffffffff81333f5b>] pciehp_unconfigure_device+0x9b/0x180
[ 1003.342877]  [<ffffffff81333a73>] pciehp_disable_slot+0x43/0xb0
[ 1003.342878]  [<ffffffff81333b6d>] pciehp_power_thread+0x8d/0xb0
[ 1003.342885]  [<ffffffff810881b2>] process_one_work+0x152/0x3d0
[ 1003.342886]  [<ffffffff8108854a>] worker_thread+0x11a/0x460
[ 1003.342887]  [<ffffffff81088430>] ? process_one_work+0x3d0/0x3d0
[ 1003.342890]  [<ffffffff8108ddd9>] kthread+0xc9/0xe0
[ 1003.342891]  [<ffffffff8108dd10>] ? kthread_create_on_node+0x180/0x180
[ 1003.342893]  [<ffffffff8164e29f>] ret_from_fork+0x3f/0x70
[ 1003.342894]  [<ffffffff8108dd10>] ? kthread_create_on_node+0x180/0x180
[ 1003.342895] ---[ end trace 65a77e06d5aa9358 ]---

Upon looking at the igb driver, I see that igb_rd32() attempted to read from
hw_addr and failed, so it set hw->hw_addr to NULL and spit out the message
in the log output above, "PCIe link lost, device now detached".

Well, now that hw_addr is NULL, the attempt to call pci_iounmap is obviously
not going to go well. As suggested by Mark Rustad, do something similar to
what ixgbe does, and save a copy of hw_addr as adapter->io_addr, so we can
still call pci_iounmap on it on teardown. Additionally, for consistency,
make the pci_iomap call assignment directly to io_addr, so map and unmap
match.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>