This patch updates the Solution Engine 7724 board code to use
in-SoC KEYSC resources for the keyboard platform device. Using
the in-SoC key scan controller fixes a crash-during-resume issue.

Without this patch the KEYSC hardware block located in the board
specific FPGA is used together with an external IRQ which is
routed through the FPGA and handled by some board specific demux
code. This board specific FPGA interrupt code does not implement
desc->set_wake() so the enable_irq_wake() call in the sh_keysc
driver will fail at suspend-to-ram time and the disable_irq_wake()
will bomb out when resuming.

Changing the platform data to use the in-SoC KEYSC hardware makes
the se7724 board support code less special which is a good thing.
Also, the board specific KEYSC pin setup code selects in-SoC pin
functions already which makes the current FPGA platform device data
look like a typo.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Convert the AP325RXA board code to register devices at
arch_initcall() time instead of device_initcall(). This
fix unbreaks pcf8563 RTC driver support.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Convert the Migo-R board code to register devices at
arch_initcall() time instead of __initcall(). This fix
unbreaks migor_ts touch screen driver support.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Convert the processor platform device setup
functions from __initcall() and sometimes
device_initcall() to arch_initcall().

This makes sure that the platform devices are
registered a bit earlier so the devices are
available when drivers register using initcall
levels earlier than device_initcall().

A good example is platform devices needed by
i2c-sh_mobile.c which registers a bit earlier
using subsys_initcall().
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Those definitions are already provided by asm-generic
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

mm: Pass virtual address to [__]p{te,ud,md}_free_tlb()

Upcoming paches to support the new 64-bit "BookE" powerpc architecture
will need to have the virtual address corresponding to PTE page when
freeing it, due to the way the HW table walker works.

Basically, the TLB can be loaded with "large" pages that cover the whole
virtual space (well, sort-of, half of it actually) represented by a PTE
page, and which contain an "indirect" bit indicating that this TLB entry
RPN points to an array of PTEs from which the TLB can then create direct
entries. Thus, in order to invalidate those when PTE pages are deleted,
we need the virtual address to pass to tlbilx or tlbivax instructions.

The old trick of sticking it somewhere in the PTE page struct page sucks
too much, the address is almost readily available in all call sites and
almost everybody implemets these as macros, so we may as well add the
argument everywhere. I added it to the pmd and pud variants for consistency.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Howells <dhowells@redhat.com> [MN10300 & FRV]
Acked-by: NNick Piggin <npiggin@suse.de>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
  It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT

  This will make hardirq.h inclusion cheaper for every PREEMPT=n config
  (which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull the initial preempt_count value into a single
definition site.

Maintainers for: alpha, ia64 and m68k, please have a look,
your arch code is funny.

The header magic is a bit odd, but similar to the KERNEL_DS
one, CPP waits with expanding these macros until the
INIT_THREAD_INFO macro itself is expanded, which is in
arch/*/kernel/init_task.c where we've already included
sched.h so we're good.

Cc: tony.luck@intel.com
Cc: rth@twiddle.net
Cc: geert@linux-m68k.org
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: NMatt Mackall <mpm@selenic.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add USB host support for port CN27 on the Solution Engine 7724
board. The r8a66597-hcd driver is hooked up as a platform device
and some registers are configured to enable the USB host function.
The hardware driving the USB port is the on-chip USB0 block in
the sh7724 processor configured as USB host controller.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Fixes up recent build breakage.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

When arch/sh/include/asm/syscall_32.h is included from a file that
doesn't also include linux/err.h the following error is produced,

In file included from /home/matt/src/kernels/sh-2.6/arch/sh/include/asm/syscall.h:5,
                 from kernel/trace/trace_syscalls.c:3:
/home/matt/src/kernels/sh-2.6/arch/sh/include/asm/syscall_32.h: In function 'syscall_get_error':
/home/matt/src/kernels/sh-2.6/arch/sh/include/asm/syscall_32.h:28: error: implicit declaration of function 'IS_ERR_VALUE'
make[2]: *** [kernel/trace/trace_syscalls.o] Error 1
make[1]: *** [kernel/trace] Error 2
make: *** [kernel] Error 2
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Re-add LCDC fbdev support to the Migo-R defconfig.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Use "ceu0" and "ceu1" as CEU names instead of "ceu".
This fixes "memchunk" kernel command line selection
on the solution engine 7724 board.

With this patch applied use "memchunk.ceu0=1m" or
"memchunk.ceu1=1m" on kernel command line to override
physically memory size to one meg for CEU0 or CEU1.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This was killed off in generic code some time ago, kill off the left over
symbol.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

sh64 can use these as well, so tie them up there as well.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds page fault instrumentation for the software performance
counters. Follows the x86 and powerpc changes.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Fixes up a recently introduced build error.
Reported-by: NKyle McMartin <kyle@mcmartin.ca>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

That's HAVE_PERF_COUNTERS not HAVE_PERF_COUNTER. This was right
initially but I seem to have screwed it up while re-typing it out
by hand on another machine when I checked it in. Hmph.
Reported-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

commit dbe6f186
("dma-mapping: mark dma_sync_single and dma_sync_sg as deprecated"
conveniently broke every single SH build.

In the future it would be great if people could at least bother
figuring out how to use grep.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

SH7786 is roughly identical to SH-X3 proto SMP, though there are only 2
CPUs. This just wraps in to the existing SH-X3 SMP code with some minor
changes for SH7786, including wiring up the IPIs properly, enabling
IRQ_PER_CPU, and so forth.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Now that sh64 also can use the uncached section, wire up the fixmap for
it as well.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

set_pte_phys() presently uses the global flush_tlb_one(), which locks on
SMP trying to do the IPI. As we have not even initialized the other CPUs
at this point, switch to the local_ variant so the flush happens on the
boot CPU.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Crib the x86 cpu_idle_wait() implementation and shove it in with the
idle code, subsequently enabling ARCH_HAS_CPU_IDLE_WAIT.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This allows the callers to now pass down the full set of FAULT_FLAG_xyz
flags to handle_mm_fault().  All callers have been (mechanically)
converted to the new calling convention, there's almost certainly room
for architectures to clean up their code and then add FAULT_FLAG_RETRY
when that support is added.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

avr32, mn10300, parisc, s390, sh, xtensa:

They never set PT_DTRACE, but clear it after do_execve().
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: NKyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Acked-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Acked-by: NChris Zankel <chris@zankel.net>
Acked-by: NRoland McGrath <roland@redhat.com>
Acked-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

GCC 4.5.0 complains about the declaration of variables
__kernel_sigreturn and __kernel_rt_sigreturn because they have type
void.  Correctly declare these symbols as functions to fix the
following error,

arch/sh/kernel/signal_32.c: In function 'setup_frame':
arch/sh/kernel/signal_32.c:368:14: error: taking address of expression of type 'void'
arch/sh/kernel/signal_32.c: In function 'setup_rt_frame':
arch/sh/kernel/signal_32.c:452:14: error: taking address of expression of type 'void'
make[1]: *** [arch/sh/kernel/signal_32.o] Error 1
make: *** [arch/sh/kernel] Error 2
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The MEDIA_SUPPORT option disabled soc-camera support, so re-enable it for
the impacted defconfigs.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

arch/sh has a couple of stray markers without any users introduced
in commit 3d58695e.  Remove them in
preparation of removing the markers in favour of the TRACE_EVENT
macro (and also because we don't keep dead code around).
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This function was only used by pci_claim_resource(), and the last commit
deleted that use.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds initial support for the PCI-Express module in the SH7786,
particularly as it relates to the urquell platform. Presently it is
only supported in root complex mode, with endpoint mode still requiring
more debugging. 29/32-bit mode and lane configurations are selectable via
board mode pins, and are otherwise fixed.

Only 4x and 1x PCI channels are presently handled, the PCI bridge still
requires additional debugging and stabilization in hardware.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This enables support for the generic software-based perf counters.

Hardware counter support could be added in the future, but the lack
of a performance counter IRQ makes this rather dubious.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Unify i2c camera device platform data to point to struct soc_camera_link
for a smooth transition to soc-camera as a platform driver.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

and remove redundant parameter for r8a66597-hcd.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

and remove redundant parameter for r8a66597-hcd.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>