This patch updates the Solution Engine 7724 board code to use
in-SoC KEYSC resources for the keyboard platform device. Using
the in-SoC key scan controller fixes a crash-during-resume issue.

Without this patch the KEYSC hardware block located in the board
specific FPGA is used together with an external IRQ which is
routed through the FPGA and handled by some board specific demux
code. This board specific FPGA interrupt code does not implement
desc->set_wake() so the enable_irq_wake() call in the sh_keysc
driver will fail at suspend-to-ram time and the disable_irq_wake()
will bomb out when resuming.

Changing the platform data to use the in-SoC KEYSC hardware makes
the se7724 board support code less special which is a good thing.
Also, the board specific KEYSC pin setup code selects in-SoC pin
functions already which makes the current FPGA platform device data
look like a typo.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Convert the AP325RXA board code to register devices at
arch_initcall() time instead of device_initcall(). This
fix unbreaks pcf8563 RTC driver support.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Convert the Migo-R board code to register devices at
arch_initcall() time instead of __initcall(). This fix
unbreaks migor_ts touch screen driver support.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Convert the processor platform device setup
functions from __initcall() and sometimes
device_initcall() to arch_initcall().

This makes sure that the platform devices are
registered a bit earlier so the devices are
available when drivers register using initcall
levels earlier than device_initcall().

A good example is platform devices needed by
i2c-sh_mobile.c which registers a bit earlier
using subsys_initcall().
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Johannes Stezenbach reported that his Pentium-M based
laptop does not have the local APIC enabled by default,
and hence perfcounters do not get initialized.

Add a fallback for this case: allow non-sampled counters
and return with an error on sampled counters. This allows
'perf stat' to work out of box - and allows 'perf top'
and 'perf record' to fall back on a hrtimer based sampling
method.

( Passing 'lapic' on the boot line will allow hardware
  sampling to occur - but if the APIC is disabled
  permanently by the hardware then this fallback still
  allows more systems to use perfcounters. )

Also decouple perfcounter support from X86_LOCAL_APIC.

-v2: fix typo breaking counters on all other systems ...
Reported-by: NJohannes Stezenbach <js@sig21.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Kernel is broken for x86 CPUs without CPUID since 2.6.28. It
crashes with NULL pointer dereference in identify_cpu():

766        generic_identify(c);
767
768-->     if (this_cpu->c_identify)
769               this_cpu->c_identify(c);

this_cpu is NULL. This is because it's only initialized in
get_cpu_vendor() function, which is not called if the CPU has
no CPUID instruction.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
LKML-Reference: <200908112000.15993.linux@rainbow-software.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Missing test after ioremap()
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NFenghua Yu <fenghua.yu@intel.com>

Make cache_add_dev exit sysfs when kobject_init_and_add returns an error.
Signed-off-by: NXiaotian Feng <dfeng@redhat.com>
Signed-off-by: NFenghua Yu <fenghua.yu@intel.com>

Between GCC version 3.4.0 and 4.3.3 (including 3.4.0 and 4.3.3), -mtune=merced
is implemented in GCC. Starting from 4.4.0, -mtune=merced is deprecated.

Even implemented in versions between 3.4.0 and 4.3.3, the -mtune=merced
feature has been broken in some of the versions. For example, GCC 4.1.2 reports
interanl tuning function errors during kernel building with -mtune=merced. Or
GCC Bugzilla 16130 reports another -mtune=merced issue on GCC 3.4.1.

So I would remove the -mtune=merced from IA64 kernel build. Without this option,
kernel on Merced will remain the same except losing an unstable and out-of-date
performance tunning feature.

Since GCC version 3.4.0, -mtune=mckinley has been implemented. The
-mtune=mckinley option functions the same as mtune=itanium2. And mtune=itanium2
is the default option. So we don't need to add mtune=mckinley either since its
been the default option in any GCC version which implements this option.
Signed-off-by: NFenghua Yu <fenghua.yu@intel.com>

fix the following 'make includecheck' warning:

  arch/ia64/include/asm/pgtable.h: asm/processor.h is included more than once.
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: NFenghua Yu <fenghua.yu@intel.com>

fix the following 'make includecheck' warning:

  arch/ia64/kernel/ia64_ksyms.c: asm/page.h is included more than once.
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: NFenghua Yu <fenghua.yu@intel.com>

__test_and_clear_bit() returns a bitfield with the tested-for bit set.
Make it consistent with the other bitops - of ia64 but also every
other architecture - and return a boolean value.
Signed-off-by: NJohannes Weiner <hannes@cmpxchg.org>
Acked-by: NFenghua Yu <fenghua.yu@intel.com>

In commit 160c1d8e,
dma_ops->dma_supported = iommu_dma_supported;

This dma_ops->dma_supported is first called in platform_dma_init() during kernel
boot. Then dma_ops->dma_supported will be called recursively in
iommu_dma_supported.

Kernel can not boot because kernel can not get out of iommu_dma_supported until
it runs out of stack memory.
Signed-off-by: NFenghua Yu <fenghua.yu@intel.com>

Due to an erratum with certain AMD Athlon 64 processors, the
BIOS may need to force enable the LAHF_LM capability.
Unfortunately, in at least one case, the BIOS does this even
for processors that do not support the functionality.

Add a specific check that will clear the feature bit for
processors known not to support the LAHF/SAHF instructions.
Signed-off-by: NKevin Winchester <kjwinchester@gmail.com>
Acked-by: NBorislav Petkov <petkovbb@googlemail.com>
LKML-Reference: <4A80A5AD.2000209@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Johannes Stezenbach reported that 'perf stat' does not count
cache-miss and cache-references events on his Pentium-M based
laptop.

This is because we left them blank in p6_perfmon_event_map[],
fill them in.
Reported-by: NJohannes Stezenbach <js@sig21.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Instead of this garbled bootup on UP Pentium-M systems:

[    0.015048] Performance Counters:
[    0.016004] no Local APIC, try rebooting with lapicno PMU driver, software counters only.

Print:

[    0.015050] Performance Counters:
[    0.016004] no APIC, boot with the "lapic" boot parameter to force-enable it.
[    0.017003] no PMU driver, software counters only.

Cf: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

My Latitude d630 seems to be handling thermal events in SMI by
lowering the max frequency of the CPU till it cools down but
still leaks the "everything is normal" events.

This spams the console and with high priority printks.

Adjust therm_throt driver to only print messages about the fact
that temperatire returned back to normal when leaving the
throttling state.

Also lower the severity of "back to normal" message from
KERN_CRIT to KERN_INFO.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Acked-by: NH. Peter Anvin <hpa@zytor.com>
LKML-Reference: <20090810051513.0558F526EC9@mailhub.coreip.homeip.net>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Reboot does not work on my MacBook Pro 13 inch (MacBookPro5,5)
too. It seems all unibody MacBook and MacBookPro require
PCI reboot handling, i guess.

Following model/machine ID list shows unibody MacBook/Pro have
the 5 series of model number:

   http://www.everymac.com/systems/by_capability/macs-by-machine-model-machine-id.htmlSigned-off-by: NShunichi Fuji <palglowr@gmail.com>
Cc: Ozan Çağlayan <ozan@pardus.org.tr>
LKML-Reference: <30046e3b0908101134p6487ddbftd8776e4ddef204be@mail.gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Wei Chong Tan reported a fast-PIT-calibration corner-case:

| pit_expect_msb() is vulnerable to SMI disturbance corner case
| in some platforms which causes /proc/cpuinfo to show wrong
| CPU MHz value when quick_pit_calibrate() jumps to success
| section.

I think that the real issue isn't even an SMI - but the fact
that in the very last iteration of the loop, there's no
serializing instruction _after_ the last 'rdtsc'. So even in
the absense of SMI's, we do have a situation where the cycle
counter was read without proper serialization.

The last check should be done outside the outer loop, since
_inside_ the outer loop, we'll be testing that the PIT has
the right MSB value has the right value in the next iteration.

So only the _last_ iteration is special, because that's the one
that will not check the PIT MSB value any more, and because the
final 'get_cycles()' isn't serialized.

In other words:

 - I'd like to move the PIT MSB check to after the last
   iteration, rather than in every iteration

 - I think we should comment on the fact that it's also a
   serializing instruction and so 'fences in' the TSC read.

Here's a suggested replacement.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Reported-by: N"Tan, Wei Chong" <wei.chong.tan@intel.com>
Tested-by: N"Tan, Wei Chong" <wei.chong.tan@intel.com>
LKML-Reference: <B28277FD4E0F9247A3D55704C440A140D5D683F3@pgsmsx504.gar.corp.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Fix the following 'make includecheck' warning:

  arch/mn10300/include/asm/pci.h: linux/mm.h is included more than once.
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On an iMac G5, the b43 driver is failing to initialise because trying to
set the dma mask to 30-bit fails. Even though there's only 512MiB of RAM
in the machine anyway:
	https://bugzilla.redhat.com/show_bug.cgi?id=514787

We should probably let it succeed if the available RAM in the system
doesn't exceed the requested limit.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If we have the powerpc perf_counter backend compiled in, but
the cpu we are running on is one where we don't support the
PMU, we currently oops in hw_perf_group_sched_in if we try to
use any counters, because ppmu is NULL in that case, and we
unconditionally dereference ppmu.

This fixes the problem by adding a check if ppmu is NULL at the
beginning of hw_perf_group_sched_in, and also at the beginning
of the other functions that get called from the perf_counter
core, i.e. hw_perf_disable, hw_perf_enable, and
hw_perf_counter_setup.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: benh@kernel.crashing.org
Signed-off-by: NIngo Molnar <mingo@elte.hu>

If the vendor name (from c16) can be longer than 100 bytes (or missing a
terminating null), then the null is written past the end of vendor[].

Found with Parfait, http://research.sun.com/projects/parfait/Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Cc: Huang Ying <ying.huang@intel.com>

MacBookPro5,1 is not able to reboot unless reboot=pci is set.
This patch forces it through a DMI quirk specific to this
device.
Signed-off-by: NOzan Çağlayan <ozan@pardus.org.tr>
LKML-Reference: <1249403971-6543-1-git-send-email-ozan@pardus.org.tr>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

found a system where x2apic reports an MSI-X irq initialization
failure:

[  302.859446] igbvf 0000:81:10.4: enabling device (0000 -> 0002)
[  302.874369] igbvf 0000:81:10.4: using 64bit DMA mask
[  302.879023] igbvf 0000:81:10.4: using 64bit consistent DMA mask
[  302.894386] igbvf 0000:81:10.4: enabling bus mastering
[  302.898171] igbvf 0000:81:10.4: setting latency timer to 64
[  302.914050] reserve_memtype added 0xefb08000-0xefb0c000, track uncached-minus, req uncached-minus, ret uncached-minus
[  302.933839] reserve_memtype added 0xefb28000-0xefb29000, track uncached-minus, req uncached-minus, ret uncached-minus
[  302.940367]   alloc irq_desc for 265 on node 4
[  302.956874]   alloc kstat_irqs on node 4
[  302.959452] alloc irq_2_iommu on node 0
[  302.974328] igbvf 0000:81:10.4: irq 265 for MSI/MSI-X
[  302.977778]   alloc irq_desc for 266 on node 4
[  302.980347]   alloc kstat_irqs on node 4
[  302.995312] free_memtype request 0xefb28000-0xefb29000
[  302.998816] igbvf 0000:81:10.4: Failed to initialize MSI-X interrupts.

... it turns out that when trying to enable MSI-X,
__assign_irq_vector(new, cfg_new, apic->target_cpus()) can not
get vector because for x2apic target-cpus returns cpumask_of(0)

Update that to online_mask like xapic.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NSuresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <4A785AFF.3050902@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

OMAP3EVM uses ISP1504 phy which doesn't require any programming and
thus has to use NOP otg transceiver.

Cleanups being done:
	- Remove unwanted code in usb-musb.c file
	- Register NOP in OMAP3EVM board file using
	  usb_nop_xceiv_register().
	- Select NOP_USB_XCEIV for OMAP3EVM boards.
	- Don't enable TWL4030_USB in omap3_evm_defconfig
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NEino-Ville Talvala <talvala@stanford.edu>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Check whether index is within bounds before testing the element.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Currently, the machine_flags are stored late in the startup
initialization which results in failing machine type checks
(e.g. for MACHINE_IS_VM).
To allow these checks, store the machine flags in the lowcore
when the machine type has been detected.

Moving the machine_flags to the lowcore has been introduced with
git commit 25097bf1Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

If the current CPU doesn't support performance counters,
cur_cpu_spec->oprofile_cpu_type can be NULL. The current
perf_counter modules don't test for that case and would thus
crash at boot time.

Bug reported by David Woodhouse.
Reported-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
LKML-Reference: <19066.48028.446975.501454@cargo.ozlabs.ibm.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Otherwise the host can spend too long traversing an rmap chain, which
happens under a spinlock.

Cc: stable@kernel.org
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

<linux/clk.h> should be included to get the base API prototypes.

This fixes the following sparse warnings:

  arch/arm/common/clkdev.c:65:12:
    warning: symbol 'clk_get_sys' was not declared. Should it be static?

  arch/arm/common/clkdev.c:79:12:
    warning: symbol 'clk_get' was not declared. Should it be static?

  arch/arm/common/clkdev.c:87:6:
    warning: symbol 'clk_put' was not declared. Should it be static?
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

preserve_crunch_context() calls __copy_to_user() which expects the
destination address to be in __user space.  setup_sigframe() properly
passes the destination address.

restore_crunch_context() calls __copy_from_user() which expects the
source address to be in __user space.  restore_sigframe() properly
passes the source address.

This fixes {preserve/restore}_crunch_context() to accept the
address as __user space and resolves the following sparse warnings:

  arch/arm/kernel/signal.c:146:31:
     warning: incorrect type in argument 1 (different address spaces)
        expected void [noderef] <asn:1>*to
        got struct crunch_sigframe *frame

  arch/arm/kernel/signal.c:156:38:
     warning: incorrect type in argument 2 (different address spaces)
        expected void const [noderef] <asn:1>*from
        got struct crunch_sigframe *frame

  arch/arm/kernel/signal.c:250:48:
     warning: incorrect type in argument 1 (different address spaces)
        expected struct crunch_sigframe *frame
        got struct crunch_sigframe [noderef] <asn:1>*<noident>

  arch/arm/kernel/signal.c:365:49:
     warning: incorrect type in argument 1 (different address spaces)
        expected struct crunch_sigframe *frame
        got struct crunch_sigframe [noderef] <asn:1>*<noident>
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Stop referencing CLOCK_TICK_RATE in the KS8695 drivers, rather refer
to a KS8695_CLOCK_RATE.
Issue pointed out by Russell King on arm-linux-kernel mailing list.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Eliminates this compiler warning:

arch/powerpc/kvm/../../../virt/kvm/kvm_main.c:1178: error: integer overflow in expression
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAvi Kivity <avi@redhat.com>

There are two waitqueues in kvm for wait handling:
vcpu->wq for virt/kvm/kvm_main.c and
vpcu->arch.local_int.wq for the s390 specific wait code.

the wait handling in kvm_s390_handle_wait was broken by using different
wait_queues for add_wait queue and remove_wait_queue.

There are two options to fix the problem:
o  move all the s390 specific code to vcpu->wq and remove
   vcpu->arch.local_int.wq
o  move all the s390 specific code to vcpu->arch.local_int.wq

This patch chooses the 2nd variant for two reasons:
o  s390 does not use kvm_vcpu_block but implements its own enabled wait
   handling.
   Having a separate wait_queue make it clear, that our wait mechanism is
   different
o  the patch is much smaller
Report-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We have to disable preemption and IRQs on every exit from
handle_invalid_guest_state, otherwise we generate at least a
preempt_disable imbalance.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Release and re-acquire preemption and IRQ lock in the same order as
vcpu_enter_guest does.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

kvm_mmu_change_mmu_pages mishandles the case where n_alloc_mmu_pages is
smaller then n_free_mmu_pages, by not checking if the result of
the subtraction is negative.

Its a valid condition which can happen if a large number of pages has
been recently freed.
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

If a migrated vcpu matches the asid_generation value of the target pcpu,
there will be no TLB flush via TLB_CONTROL_FLUSH_ALL_ASID.

The check for vcpu.cpu in pre_svm_run is meaningless since svm_vcpu_load
already updated it on schedule in.

Such vcpu will VMRUN with stale TLB entries.

Based on original patch from Joerg Roedel (http://patchwork.kernel.org/patch/10021/)
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Acked-by: NJoerg Roedel <joerg.roedel@amd.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>