Move the code that identifies the chip ID and selects the appropriate
firmware to an operation implemented by the lower driver.  Also move
the quirks definitions into wlcore.h and rename to WLCORE_QUIRK_*.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add register tables support in wlcore, add some new IO functions to
read and write to chip-specific register and data addresses.  Move
some common register values from wl12xx to wlcore and add the
registers table to wl12xx.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add partition tables to wlcore, move and reorganize partition setting
functions.  Move wl12xx partition table to use the wlcore partition
table instead.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In order to add chip-specific operations and prepare for future
elements that need to be set by the lower driver, move the wl1271
structure to the wlcore.h file and add an empty placeholder for the
operations structure.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We need to set some parameters (eg. partition and register tables)
during probe of the lower driver, so split the probe function, leaving
most of it in wlcore, but moving the hw struct allocation to the lower
driver.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Create a new small wl12xx module that only contains the probe
functions and depends entirely on wlcore otherwise.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Rename the wl12xx driver directory to wlcore as an initial step
towards the split of the driver into wlcore and wl12xx.  We just
rename the directory first to keep git blame happy.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Move wl12xx and wl1251 modules into a new drivers/net/wireless/ti
directory.  Add a TI WLAN Kconfig option and Makefile to support this
change.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Cc: John W. Linville <linville@tuxdriver.com>

In certain scenarios involving sched scan + normal scan + COEX
scan could take longer than 10s and this triggers a recovery
where it shouldn't. Increase the timeout to avoid that.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Set the dwell times for sched scan according to the number
of probe requests which are going to be transmitted.
This should fix the too short dwell time problem which
prevented some of the probe requests from being transmitted
in cases of high number of SSIDs (10+) to be actively sched scanned.
However, in the common case of having up to 1-2 SSIDs that
require active scan, the dwell time would be kept to a minimum
which should conserve power. This is important as sched scan
also runs periodically while the host is suspended and there's
great importance to keep power consumption as low as possible.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
[fixed a couple of new strict checkpatch warnings]
Signed-off-by: NLuciano Coelho <coelho@ti.com>

wlvif->probereq is zeroed when adding an interface but
the skb pointed to isn't freed when the interface is removed.
This would lead to a mem leak on every recovery.
Fix it by freeing the skb when removing the interface.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The ap keys should be freed only when removing
ap role (otherwise, some arbitrary data might
get freed).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

On the PandaBoard (omap_hsmmc + wl12xx_sdio) with DMA_API_DEBUG:

 WARNING: at lib/dma-debug.c:930 check_for_stack.part.8+0x7c/0xe0()
 omap_hsmmc omap_hsmmc.4: DMA-API: device driver maps memory fromstack
Signed-off-by: NMircea Gherzan <mgherzan@gmail.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The iteration on the wlvif list in wl1271_op_resume/suspend was
perfomed before locking wl->mutex which would lead to a kernel
panic in case a recovery was queued at the same time
and would delete the wlvifs from the list.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Channel switch complete event wasn't handled
properly in station mode, as we checked wrong
CS flag.
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

wl12xx sets the do_join flag (which later starts the
sta role) when the bssid was changed and the sta is
associated. However, this no longer happens after
the "mac80211: remove spurious BSSID change flag"
patch.

Fix it by setting the do_join flag on BSS_CHANGED_ASSOC
(for IBSS, do_join is already set on BSS_CHANGED_IBSS)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Move the POWER_PMI to the op_mode where it is changed.  The trans needs
to check it frequently, so shadow the status in the trans and update it
in trans when it infrequently changes.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The op_mode should check for FW_ERROR before calling send_cmd.  This
removes the need to test for FW_ERROR in the trans layer.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With error logging now completely handled in
the op_mode, the transport layer does not
need to know information about the loaded
firmware.

Remove this state information from the
iwl_shared data structure.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_get_single_channel_number is used only in
iwl-scan.c, move it there and mark it static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_full_rxon_required is used only in
iwl-agn-rxon.c. Move it there and mark it
static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_check_rxon_cmd is used only in
iwl-agn-rxon.c. Move it there and mark it
static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_set_rxon_hwcrypto is used only in
iwl-agn-rxon.c. Move it there and mark it
static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_send_rxon_timing is used only in
iwl-agn-rxon.c, move it there and mark it
static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is used only in one file, move it there
and make it static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This variable holds the ucode currently
running on the device; which is determined by
op_mode, so move this parameter there.

Also, the name of the variable is a bit
misleading, so rename it to cur_ucode.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Error log reporting does not belong to the
transport layer, but to the op_mode loading
the ucode, as it is the entity which knows
about the ucode loaded, and what the error
information means.

Move device logging pointers from the
transport layer to op_mode.

With this change, transport layer only
reports an error to the op_mode, which will
figure out what to do with the error. This
causes the driver to now dump out error logs
when the command queue is stuck as well.

Also, move the debugfs entry for event logs
out of the transport layer and into op_mode.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_nic_error is used in iwl-agn.c only, move
it there and make it static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the process, make iwlagn_fw_error
a non-static function, as it is used
by more than one file.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No other component is accessing it any more,
so it can move to the correct place in priv.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The queue mapping is not only dynamic, it
is also dependent on the uCode, as we can
already see today with the dual-mode and
non-dual-mode being different.

Move the queue mapping out of the transport
layer and let the higher layer manage it.
Part of the transport configuration is how
to set up the queues.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As idle is just a deep powersave mode for
the device, it will easily scan while idle
since that turns off powersave.

This reduces the number of commands sent
to the device when scanning.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is not (no longer?) used by any device
so just remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is used only by 2000 class devices, but
they all use it so remove the configuration
parameter and hard-code the programming.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's no device using this mechanism.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It talks about treating different uCode APIs
as different pieces of hardware which really
isn't how we handle things.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A whole bunch of messages, even some recent ones,
didn't include a trailing newline so add it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The calibration results all come in while we're
waiting for the calibration complete notification.
As a consequence, there's no need to install a
global RX handler for them, we can use the newly
extended notification wait framework for this and
make the code easier to follow.

It is now quite explicit that we are processing
the calibration results while waiting for the
complete notification, before this was implicit
and developers had to know this to understand why
we wait for the calibration complete notification
and what happens while we wait.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sometimes, for example when we ask the uCode
for calibration, we wait for the "complete"
response while we also need the results that
are sent in other, interim, notifications.

Currently we handle this by installing an RX
handler globally, but that isn't needed as
this is the only time we want to use these
notifications.

So in order to be able to simplify at least
future code that does the same, extend the
notification wait framework to allow you to
wait for multiple commands and decide based
on the command whether the wait finished.

While at it, also fix a race that can then
become relevant -- if the wait function has
returned true once it shouldn't be called
again, today this can happen due to races
between the triggering and the wakeup.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The flow handler (hardware) can put multiple
frames into a single RX buffer. To handle
this, walk the RX buffer and check if there
are multiple valid packets in it.

To let the upper layer handle this correctly
introduce rxb_offset() which is needed when
we pass pages to mac80211 -- we need to know
the offset into the page there.

Also change the page handling scheme to use
refcounting. Anyone who needs a page will
"steal" it, which marks it as having been
used & refcounts it. The RX handler then has
to free its own reference and must not reuse
the page.

Finally, do not set the bit asking the FH to
give us each packet in a single buffer. This
really enables the feature.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>