- 30 4月, 2009 1 次提交
-
-
由 Ben Hutchings 提交于
Make use of the newly-added generic MDIO clause 45 support and remove redundant definitions. Add an 'efx_' prefix to the remaining driver-specific MDIO functions and remove arguments which are redundant with efx->mdio.prtad. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 13 12月, 2008 3 次提交
-
-
由 Ben Hutchings 提交于
Add support code for the SFN4111T 100/1000/10GBASE-T reference design, based in part on the existing code for the SFE4001. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ben Hutchings 提交于
From: Steve Hodgson <shodgson@solarflare.com> MAC, PHY and board events may be separately enabled and signalled. Our current arrangement of chaining the polling functions can result in events being missed. Change them to be more independent. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ben Hutchings 提交于
The SFC4000 has a separate MAC for use at sub-10G speeds. Introduce an efx_mac_operations structure with implementations for the two MACs. Switch between the MACs as necessary. PHY settings are independent of the MAC, so add get_settings() and set_settings() to efx_phy_operations. Also add macs field to indicate which MACs the PHY is connected to. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 06 11月, 2008 1 次提交
-
-
由 Ben Hutchings 提交于
Move flash and EEPROM partition boundary constants into spi.h and rename them to be consistent. Add a comment on the partitioning. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
- 25 9月, 2008 1 次提交
-
-
由 Ben Hutchings 提交于
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
- 03 9月, 2008 4 次提交
-
-
由 Ben Hutchings 提交于
Include PMA/PMD in loopback self-tests as intended. Add NVRAM checksum validation and include it in self-tests. Add register self-tests. Run PHY self-tests where available. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
由 Ben Hutchings 提交于
This will support register self-tests. From: Steve Hodgson <shodgson@solarflare.com> Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
由 Ben Hutchings 提交于
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
由 Ben Hutchings 提交于
Extend the SPI device setup code to support this. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
- 22 5月, 2008 1 次提交
-
-
由 Ben Hutchings 提交于
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
- 13 5月, 2008 1 次提交
-
-
由 Ben Hutchings 提交于
Add a set of self-tests accessible thorugh ethtool. Add hardware loopback and TX disable control code to support them. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
- 29 4月, 2008 1 次提交
-
-
由 Ben Hutchings 提交于
The driver supports the 10Xpress PHY and XFP modules on our reference designs SFE4001 and SFE4002 and the SMC models SMC10GPCIe-XFP and SMC10GPCIe-10BT. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-