提交 6f158d5f 编写于 作者: B Ben Hutchings 提交者: David S. Miller

sfc: Add support for SFN4111T

Add support code for the SFN4111T 100/1000/10GBASE-T reference design,
based in part on the existing code for the SFE4001.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 e6fa2eb7
......@@ -241,6 +241,8 @@ struct efx_board_data {
static struct efx_board_data board_data[] = {
{ EFX_BOARD_SFE4001, "SFE4001", "10GBASE-T adapter", sfe4001_init },
{ EFX_BOARD_SFE4002, "SFE4002", "XFP adapter", sfe4002_init },
{ EFX_BOARD_SFN4111T, "SFN4111T", "100/1000/10GBASE-T adapter",
sfn4111t_init },
};
void efx_set_board_info(struct efx_nic *efx, u16 revision_info)
......
......@@ -12,11 +12,16 @@
/* Board IDs (must fit in 8 bits) */
enum efx_board_type {
EFX_BOARD_SFE4001 = 1, /* SFE4001 (10GBASE-T) */
EFX_BOARD_SFE4001 = 1,
EFX_BOARD_SFE4002 = 2,
EFX_BOARD_SFN4111T = 0x51,
};
extern void efx_set_board_info(struct efx_nic *efx, u16 revision_info);
/* SFE4001 (10GBASE-T) */
extern int sfe4001_init(struct efx_nic *efx);
/* SFN4111T (100/1000/10GBASE-T) */
extern int sfn4111t_init(struct efx_nic *efx);
#endif
......@@ -2971,6 +2971,13 @@ int falcon_init_nic(struct efx_nic *efx)
EFX_SET_OWORD_FIELD(temp, ONCHIP_SRAM, 1);
falcon_write(efx, &temp, NIC_STAT_REG);
/* Set the source of the GMAC clock */
if (falcon_rev(efx) == FALCON_REV_B0) {
falcon_read(efx, &temp, GPIO_CTL_REG_KER);
EFX_SET_OWORD_FIELD(temp, GPIO_USE_NIC_CLK, true);
falcon_write(efx, &temp, GPIO_CTL_REG_KER);
}
/* Set buffer table mode */
EFX_POPULATE_OWORD_1(temp, BUF_TBL_MODE, BUF_TBL_MODE_FULL);
falcon_write(efx, &temp, BUF_TBL_CFG_REG_KER);
......
......@@ -136,6 +136,8 @@
/* GPIO control register */
#define GPIO_CTL_REG_KER 0x0210
#define GPIO_USE_NIC_CLK_LBN (30)
#define GPIO_USE_NIC_CLK_WIDTH (1)
#define GPIO_OUTPUTS_LBN (16)
#define GPIO_OUTPUTS_WIDTH (4)
#define GPIO_INPUTS_LBN (8)
......
......@@ -702,8 +702,15 @@ int efx_offline_test(struct efx_nic *efx,
*/
mutex_lock(&efx->mac_lock);
efx->port_inhibited = true;
if (efx->loopback_modes)
efx->loopback_mode = __ffs(efx->loopback_modes);
if (efx->loopback_modes) {
/* We need the 312 clock from the PHY to test the XMAC
* registers, so move into XGMII loopback if available */
if (efx->loopback_modes & (1 << LOOPBACK_XGMII))
efx->loopback_mode = LOOPBACK_XGMII;
else
efx->loopback_mode = __ffs(efx->loopback_modes);
}
__efx_reconfigure_port(efx);
mutex_unlock(&efx->mac_lock);
......
/****************************************************************************
* Driver for Solarflare Solarstorm network controllers and boards
* Copyright 2007 Solarflare Communications Inc.
* Copyright 2007-2008 Solarflare Communications Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2 as published
......@@ -8,10 +8,21 @@
*/
/*****************************************************************************
* Support for the SFE4001 NIC: driver code for the PCA9539 I/O expander that
* controls the PHY power rails, and for the MAX6647 temp. sensor used to check
* the PHY
* Support for the SFE4001 and SFN4111T NICs.
*
* The SFE4001 does not power-up fully at reset due to its high power
* consumption. We control its power via a PCA9539 I/O expander.
* Both boards have a MAX6647 temperature monitor which we expose to
* the lm90 driver.
*
* This also provides minimal support for reflashing the PHY, which is
* initiated by resetting it with the FLASH_CFG_1 pin pulled down.
* On SFE4001 rev A2 and later this is connected to the 3V3X output of
* the IO-expander; on the SFN4111T it is connected to Falcon's GPIO3.
* We represent reflash mode as PHY_MODE_SPECIAL and make it mutually
* exclusive with the network device being open.
*/
#include <linux/delay.h>
#include "net_driver.h"
#include "efx.h"
......@@ -171,39 +182,30 @@ static int sfe4001_poweron(struct efx_nic *efx)
return rc;
}
static int sfe4001_check_hw(struct efx_nic *efx)
static int sfn4111t_reset(struct efx_nic *efx)
{
s32 status;
efx_oword_t reg;
/* If XAUI link is up then do not monitor */
if (EFX_WORKAROUND_7884(efx) && efx->mac_up)
return 0;
/* GPIO pins are also used for I2C, so block that temporarily */
mutex_lock(&efx->i2c_adap.bus_lock);
/* Check the powered status of the PHY. Lack of power implies that
* the MAX6647 has shut down power to it, probably due to a temp.
* alarm. Reading the power status rather than the MAX6647 status
* directly because the later is read-to-clear and would thus
* start to power up the PHY again when polled, causing us to blip
* the power undesirably.
* We know we can read from the IO expander because we did
* it during power-on. Assume failure now is bad news. */
status = i2c_smbus_read_byte_data(efx->board_info.ioexp_client, P1_IN);
if (status >= 0 &&
(status & ((1 << P1_AFE_PWD_LBN) | (1 << P1_DSP_PWD25_LBN))) != 0)
return 0;
falcon_read(efx, &reg, GPIO_CTL_REG_KER);
EFX_SET_OWORD_FIELD(reg, GPIO2_OEN, true);
EFX_SET_OWORD_FIELD(reg, GPIO2_OUT, false);
falcon_write(efx, &reg, GPIO_CTL_REG_KER);
msleep(1000);
EFX_SET_OWORD_FIELD(reg, GPIO2_OUT, true);
EFX_SET_OWORD_FIELD(reg, GPIO3_OEN, true);
EFX_SET_OWORD_FIELD(reg, GPIO3_OUT,
!(efx->phy_mode & PHY_MODE_SPECIAL));
falcon_write(efx, &reg, GPIO_CTL_REG_KER);
/* Use board power control, not PHY power control */
sfe4001_poweroff(efx);
efx->phy_mode = PHY_MODE_OFF;
mutex_unlock(&efx->i2c_adap.bus_lock);
return (status < 0) ? -EIO : -ERANGE;
ssleep(1);
return 0;
}
/* On SFE4001 rev A2 and later, we can control the FLASH_CFG_1 pin
* using the 3V3X output of the IO-expander. Allow the user to set
* this when the device is stopped, and keep it stopped then.
*/
static ssize_t show_phy_flash_cfg(struct device *dev,
struct device_attribute *attr, char *buf)
{
......@@ -231,7 +233,10 @@ static ssize_t set_phy_flash_cfg(struct device *dev,
err = -EBUSY;
} else {
efx->phy_mode = new_mode;
err = sfe4001_poweron(efx);
if (efx->board_info.type == EFX_BOARD_SFE4001)
err = sfe4001_poweron(efx);
else
err = sfn4111t_reset(efx);
efx_reconfigure_port(efx);
}
rtnl_unlock();
......@@ -251,6 +256,34 @@ static void sfe4001_fini(struct efx_nic *efx)
i2c_unregister_device(efx->board_info.hwmon_client);
}
static int sfe4001_check_hw(struct efx_nic *efx)
{
s32 status;
/* If XAUI link is up then do not monitor */
if (EFX_WORKAROUND_7884(efx) && efx->mac_up)
return 0;
/* Check the powered status of the PHY. Lack of power implies that
* the MAX6647 has shut down power to it, probably due to a temp.
* alarm. Reading the power status rather than the MAX6647 status
* directly because the later is read-to-clear and would thus
* start to power up the PHY again when polled, causing us to blip
* the power undesirably.
* We know we can read from the IO expander because we did
* it during power-on. Assume failure now is bad news. */
status = i2c_smbus_read_byte_data(efx->board_info.ioexp_client, P1_IN);
if (status >= 0 &&
(status & ((1 << P1_AFE_PWD_LBN) | (1 << P1_DSP_PWD25_LBN))) != 0)
return 0;
/* Use board power control, not PHY power control */
sfe4001_poweroff(efx);
efx->phy_mode = PHY_MODE_OFF;
return (status < 0) ? -EIO : -ERANGE;
}
static struct i2c_board_info sfe4001_hwmon_info = {
I2C_BOARD_INFO("max6647", 0x4e),
.irq = -1,
......@@ -312,3 +345,61 @@ int sfe4001_init(struct efx_nic *efx)
i2c_unregister_device(efx->board_info.hwmon_client);
return rc;
}
static int sfn4111t_check_hw(struct efx_nic *efx)
{
s32 status;
/* If XAUI link is up then do not monitor */
if (EFX_WORKAROUND_7884(efx) && efx->mac_up)
return 0;
/* Test LHIGH, RHIGH, FAULT, EOT and IOT alarms */
status = i2c_smbus_read_byte_data(efx->board_info.hwmon_client,
MAX664X_REG_RSL);
if (status < 0)
return -EIO;
if (status & 0x57)
return -ERANGE;
return 0;
}
static void sfn4111t_fini(struct efx_nic *efx)
{
EFX_INFO(efx, "%s\n", __func__);
device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
i2c_unregister_device(efx->board_info.hwmon_client);
}
static struct i2c_board_info sfn4111t_hwmon_info = {
I2C_BOARD_INFO("max6647", 0x4e),
.irq = -1,
};
int sfn4111t_init(struct efx_nic *efx)
{
int rc;
efx->board_info.hwmon_client =
i2c_new_device(&efx->i2c_adap, &sfn4111t_hwmon_info);
if (!efx->board_info.hwmon_client)
return -EIO;
efx->board_info.blink = tenxpress_phy_blink;
efx->board_info.monitor = sfn4111t_check_hw;
efx->board_info.fini = sfn4111t_fini;
rc = device_create_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
if (rc)
goto fail_hwmon;
if (efx->phy_mode & PHY_MODE_SPECIAL)
sfn4111t_reset(efx);
return 0;
fail_hwmon:
i2c_unregister_device(efx->board_info.hwmon_client);
return rc;
}
......@@ -17,6 +17,7 @@
#define EFX_WORKAROUND_ALWAYS(efx) 1
#define EFX_WORKAROUND_FALCON_A(efx) (falcon_rev(efx) <= FALCON_REV_A1)
#define EFX_WORKAROUND_10G(efx) EFX_IS10G(efx)
#define EFX_WORKAROUND_SFX7101(efx) ((efx)->phy_type == PHY_TYPE_SFX7101)
#define EFX_WORKAROUND_SFT9001A(efx) ((efx)->phy_type == PHY_TYPE_SFT9001A)
......@@ -25,7 +26,7 @@
/* RX PCIe double split performance issue */
#define EFX_WORKAROUND_7575 EFX_WORKAROUND_ALWAYS
/* Bit-bashed I2C reads cause performance drop */
#define EFX_WORKAROUND_7884 EFX_WORKAROUND_ALWAYS
#define EFX_WORKAROUND_7884 EFX_WORKAROUND_10G
/* TX pkt parser problem with <= 16 byte TXes */
#define EFX_WORKAROUND_9141 EFX_WORKAROUND_ALWAYS
/* Low rate CRC errors require XAUI reset */
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册