There're two IRQ pins output from MAX8925. One is PMIC interrupt, the other
is TSC interrupt. But they're sharing one irq chip.

After initializing MAX8925 interrupts, unexpected TSC interrupt may occur and
it can't be cleared if touch driver isn't loaded.

Now move the operation of masking TSC interrupt behind requesting PMIC
interrupt. If touch driver isn't loaded, this interrupt is always masked.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The i2c_client received in probe() should not be kfree()'d.
Signed-off-by: NRabin Vincent <rabin@rab.in>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Accessing num_reg elements in the interval [reg .. reg+num_regs)
is permitted if (reg+numregs <= array size), so barf when that
excluded upper bound is > array size. The prior -1 would give
access to one too many elements.
Signed-off-by: NPhil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The charger interrupts on the WM831x are unconditionally a wake source
for the system. If the power driver is not able to monitor them (for
example, due to the IRQ line not having been wired up on the system)
then any charger interrupt will prevent the system suspending for any
meaningful amount of time since nothing will ack them.

Avoid this issue by manually acknowledging these interrupts when we
suspend the WM831x core device if they are masked. If software is
actually using the interrupts then they will be unmasked and this
change will have no effect.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Ensure that the hardware has interrupts masked if we are not using
the interrupt controller on the WM831x by initialising the masks
before we check for the setup data required for the IRQ line. This
avoids signalling an unused IRQ line and improves the robustness
of checks that the IRQ is in use.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add touch screen input driver for TPS6507x family of multi-function
chips.  Uses the TPS6507x MFD driver.  No interrupt support due to
testing limitations of current hardware.
Signed-off-by: NTodd Fischer <todd.fischer@ridgerun.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

TPS6507x are multi function (PM, touchscreen) chipsets from TI.
This commit also changes the corresponding regulator driver from being
standalone to an MFD subdevice.
Signed-off-by: NTodd Fischer <todd.fischer@ridgerun.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Currently completion of WM831x AUXADC conversions is monitored by
checking for convertor enable. Due to the mechanism used to ensure
data corruption is avoided when reading AUXADC data there may under
heavy I/O be a window where this bit has cleared but the conversion
results have not been updated. Data availability is only guaranteed
after the AUXADC data interrupt has been asserted.

Avoid this by always using the interrupt to detect completion. If the
chip IRQ is not set up then we poll the IRQ status register for up to
5ms. If it is set up then we rely on the data done interrupt with a
vastly increased timeout, failing the conversion if the interrupt is
not generated.

This also saves a register read when using interrupts.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The Janz CMOD-IO PCI MODULbus carrier board is a PCI to MODULbus bridge,
which may host many different types of MODULbus daughterboards, including
CAN and GPIO controllers.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Reviewed-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

"pcf->irq_handler" has PCF50633_NUM_IRQ elements.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This was used by the old, pre-genirq IRQ implementation but is no
longer required.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add platform data for timb-dma, and add it in to timb-dma
in all configurations of timberdale.

Also incremented the version number.
Signed-off-by: NRichard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch fixes three section mismatches.

WARNING: drivers/mfd/88pm860x.o(.text+0x12): Section mismatch in
reference from the function pm860x_device_exit() to the function
.devexit.text:device_irq_exit()
The function pm860x_device_exit() references a function in an exit
section.
Often the function device_irq_exit() has valid usage outside the exit
section
and the fix is to remove the __devexit annotation of device_irq_exit.

WARNING: drivers/mfd/88pm860x.o(.text+0xb0): Section mismatch in
reference from the function pm860x_device_init() to the function
.devinit.text:device_8606_init()
The function pm860x_device_init() references
the function __devinit device_8606_init().
This is often because pm860x_device_init lacks a __devinit
annotation or the annotation of device_8606_init is wrong.

WARNING: drivers/mfd/88pm860x.o(.text+0xbe): Section mismatch in
reference from the function pm860x_device_init() to the function
.devinit.text:device_8607_init()
The function pm860x_device_init() references
the function __devinit device_8607_init().
This is often because pm860x_device_init lacks a __devinit
annotation or the annotation of device_8607_init is wrong.
Signed-off-by: NHenrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

If mem_base is NULL, then we fall back to the default case, just copying the
original resource.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

I'm pretty sure that it should be + 1 here.  It's an off by one, because
we start counting at zero.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NRichard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch adds a new MFD driver for the RDC321x southbridge. This southbridge
is always present in the RDC321x System-on-a-Chip and provides access to some
GPIOs as well as a watchdog. Access to these two functions is done using the
southbridge PCI device configuration space.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Fix I2C-drivers which missed setting clientdata to NULL before freeing the
structure it points to. Also fix drivers which do this _after_ the structure
was freed already.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch adds in the Xilinx I2C bus driver to some of the
configurations of the timberdale MFD.

It provides the I2C devices to the XIIC via platform data in a
similar way as done to the ocores driver.
Signed-off-by: NRichard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

We should check for pdata being not NULL before dereferencing it.
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Register a device newly added pcf50633-backlight driver as a child device in
the pcf50633 core driver.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

This add basic led support for Freescale MC13783 PMIC.
Signed-off-by: NPhilippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

A lot of condition comparision statements are used in original driver. These
statements are used to check the boundary of voltage numbers since voltage
number isn't linear.

Now use array of voltage numbers instead. Clean code with simpler way.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Remove a lot of driver structures in 88pm860x driver. Make regulators share
one driver structure.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Boards can have different supplied voltages on different SD card slots. This
information has to be passed down to the SD/MMC driver.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NIan Molton <ian@mnementh.co.uk>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NIan Molton <ian@mnementh.co.uk>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

SDHI controllers on SuperH, served by the tmio_mmc driver, can use slave DMA
for data transfer. This patch adds support for the dmaengine API to the
tmio_mmc driver.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NIan Molton <ian@mnementh.co.uk>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Pass DMA slave IDs from platform down to the tmio_mmc driver, to be used
for dmaengine configuration.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

In certain circumstances, especially under heavy load, the AUXADC
completion interrupt may be detected after we've timed out waiting for
it.  That conversion would still succeed but the next conversion will
see the completion that was signalled by the interrupt for the previous
conversion and therefore not wait for the AUXADC conversion to run,
causing it to report failure.

Provide a simple, non-invasive cleanup by using try_wait_for_completion()
to ensure that the completion is not signalled before we wait.  Since
the AUXADC is run within a mutex we know there can only have been at
most one AUXADC interrupt outstanding.  A more involved change should
follow for the next merge window.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Make dev_() prints much prettier.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The WM8994 has an interrupt controller which supports interrupts for
both CODEC and GPIO portions of the chip. Support this using genirq,
while allowing for systems that do not have an interrupt hooked up.

Wrapper functions are provided for the IRQ request and free to simplify
the code in consumer drivers when handling cases where IRQs are not
set up.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>

Implicit slab.h inclusion via percpu.h is about to go away.  Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

Correction for chips:
twl6030 is Phoenix Power chip
twl6040 is Phoenix Audio chip
Signed-off-by: NMargarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is the MFD driver for the DaVinci Voice codec, it has two clients:

* Voice codec interface
* Voice codec CQ93VC
Signed-off-by: NMiguel Aguilar <miguel.aguilar@ridgerun.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

commit 5fb4d38b ("mfd: Move WM831x to
generic IRQ") didn't take into account that genirq support depends on
GENERIC_HARDIRQS.

Additionally, 2.6.34-rc1 added:
  - commit 2afa62ea ("mfd: Use genirq in
    88pm860x").
  - commit 760e4518 ("mfd: Convert WM8350 to
    genirq").
  - commit 1f1cf8f9 ("mfd: Update irq handler
    in max8925")

Make all of them depend on GENERIC_HARDIRQS to avoid compile errors on
architectures that don't support genirq yet.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

We should only request for the MFD used region, not the whole thing.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Tested-by: NPaul Mundt <lethal@linux-sh.org>
Reviewed-by: NH Hartley Sweeten <hsweeten@visionengravers.com>

This patch fixes a build failure[1], by adding the missing semaphore.h include

References:
[1] http://kisskb.ellerman.id.au/kisskb/buildresult/2234322/Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use the completion interrupt generated by the device rather than
polling for conversions to complete. As a backup we still check
the status of the AUXADC if we don't get a completion, mostly for
systems that don't have the WM831x interrupt infrastructure hooked
up.

Also reduce the timeout for completion of conversions to 5ms from
the previous 10ms, the lower timeout should be sufficient.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use the completion interrupt generated by the device rather than
polling for conversions to complete. As a backup we still check
the state of the AUXADC if we don't get a completion, mostly for
systems that don't have the WM8350 interrupt infrastructure hooked
up.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

New function twl4030_remove_script(u8 flags) takes a script type as
defined in twl.h and prevents any script already loaded in that position
from running.  This is accomplished by programming SEQ_ADD_* to 0x3f,
the END_OF_SCRIPT value, where SEQ_ADD_* is determined by flags.

(Future) users of this function include OMAP board files for machines
facing a race condition between sleep and warm reset.
Signed-off-by: NMike Turquette <mturquette@ti.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>