There're two IRQ pins output from MAX8925. One is PMIC interrupt, the other
is TSC interrupt. But they're sharing one irq chip.

After initializing MAX8925 interrupts, unexpected TSC interrupt may occur and
it can't be cleared if touch driver isn't loaded.

Now move the operation of masking TSC interrupt behind requesting PMIC
interrupt. If touch driver isn't loaded, this interrupt is always masked.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The i2c_client received in probe() should not be kfree()'d.
Signed-off-by: NRabin Vincent <rabin@rab.in>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Accessing num_reg elements in the interval [reg .. reg+num_regs)
is permitted if (reg+numregs <= array size), so barf when that
excluded upper bound is > array size. The prior -1 would give
access to one too many elements.
Signed-off-by: NPhil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The charger interrupts on the WM831x are unconditionally a wake source
for the system. If the power driver is not able to monitor them (for
example, due to the IRQ line not having been wired up on the system)
then any charger interrupt will prevent the system suspending for any
meaningful amount of time since nothing will ack them.

Avoid this issue by manually acknowledging these interrupts when we
suspend the WM831x core device if they are masked. If software is
actually using the interrupts then they will be unmasked and this
change will have no effect.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Ensure that the hardware has interrupts masked if we are not using
the interrupt controller on the WM831x by initialising the masks
before we check for the setup data required for the IRQ line. This
avoids signalling an unused IRQ line and improves the robustness
of checks that the IRQ is in use.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add touch screen input driver for TPS6507x family of multi-function
chips.  Uses the TPS6507x MFD driver.  No interrupt support due to
testing limitations of current hardware.
Signed-off-by: NTodd Fischer <todd.fischer@ridgerun.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

TPS6507x are multi function (PM, touchscreen) chipsets from TI.
This commit also changes the corresponding regulator driver from being
standalone to an MFD subdevice.
Signed-off-by: NTodd Fischer <todd.fischer@ridgerun.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Move from using tps or tsp6507x to tps6057x_pmic in a consistent manner.
Signed-off-by: NTodd Fischer <todd.fischer@ridgerun.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add mfd structure which refrences sub-driver initialization data. For example,
for a giving hardware implementation, the voltage regulator sub-driver
initialization data provides the mapping betten a voltage regulator and what
the output voltage is being used for.
Signed-off-by: NTodd Fischer <todd.fischer@ridgerun.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Other sub-drivers for the TPS6507x chip will need to use register
definition so move it out of the source file and into a header file.
Signed-off-by: NTodd Fischer <todd.fischer@ridgerun.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Implicit slab.h inclusion via percpu.h is about to go away.  Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Currently completion of WM831x AUXADC conversions is monitored by
checking for convertor enable. Due to the mechanism used to ensure
data corruption is avoided when reading AUXADC data there may under
heavy I/O be a window where this bit has cleared but the conversion
results have not been updated. Data availability is only guaranteed
after the AUXADC data interrupt has been asserted.

Avoid this by always using the interrupt to detect completion. If the
chip IRQ is not set up then we poll the IRQ status register for up to
5ms. If it is set up then we rely on the data done interrupt with a
vastly increased timeout, failing the conversion if the interrupt is
not generated.

This also saves a register read when using interrupts.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The Janz VMOD-TTL is a MODULbus daughterboard which fits onto any MODULbus
carrier board. It essentially consists of some various logic and a Zilog
Z8536 CIO Counter/Timer and Parallel IO Unit.

The board must be physically configured with jumpers to enable a user to
drive output signals. I am only interested in outputs, so I have made this
driver as simple as possible. It only supports a very minimal subset of the
features provided by the Z8536 chip.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The Janz VMOD-ICAN3 is a MODULbus daughterboard which fits onto any
MODULbus carrier board. It is an intelligent CAN controller with a
microcontroller and associated firmware.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The Janz CMOD-IO PCI MODULbus carrier board is a PCI to MODULbus bridge,
which may host many different types of MODULbus daughterboards, including
CAN and GPIO controllers.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Reviewed-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

"pcf->irq_handler" has PCF50633_NUM_IRQ elements.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This was used by the old, pre-genirq IRQ implementation but is no
longer required.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add platform data for timb-dma, and add it in to timb-dma
in all configurations of timberdale.

Also incremented the version number.
Signed-off-by: NRichard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch fixes three section mismatches.

WARNING: drivers/mfd/88pm860x.o(.text+0x12): Section mismatch in
reference from the function pm860x_device_exit() to the function
.devexit.text:device_irq_exit()
The function pm860x_device_exit() references a function in an exit
section.
Often the function device_irq_exit() has valid usage outside the exit
section
and the fix is to remove the __devexit annotation of device_irq_exit.

WARNING: drivers/mfd/88pm860x.o(.text+0xb0): Section mismatch in
reference from the function pm860x_device_init() to the function
.devinit.text:device_8606_init()
The function pm860x_device_init() references
the function __devinit device_8606_init().
This is often because pm860x_device_init lacks a __devinit
annotation or the annotation of device_8606_init is wrong.

WARNING: drivers/mfd/88pm860x.o(.text+0xbe): Section mismatch in
reference from the function pm860x_device_init() to the function
.devinit.text:device_8607_init()
The function pm860x_device_init() references
the function __devinit device_8607_init().
This is often because pm860x_device_init lacks a __devinit
annotation or the annotation of device_8607_init is wrong.
Signed-off-by: NHenrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

If mem_base is NULL, then we fall back to the default case, just copying the
original resource.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

I'm pretty sure that it should be + 1 here.  It's an off by one, because
we start counting at zero.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NRichard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The RDC321x MFD southbridge driver will pass a reference to the
southbridge PCI device which should be used by the watchdog driver for its
operations.  This patch converts the watchdog driver to use the pci_dev
pointer and make use of the base register resource which is passed along
with the platform device.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Acked-by: NWim Van Sebroeck <wim@iguana.be>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch adds a new GPIO driver for the RDC321x SoC GPIO controller.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch adds a new MFD driver for the RDC321x southbridge. This southbridge
is always present in the RDC321x System-on-a-Chip and provides access to some
GPIOs as well as a watchdog. Access to these two functions is done using the
southbridge PCI device configuration space.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Fix I2C-drivers which missed setting clientdata to NULL before freeing the
structure it points to. Also fix drivers which do this _after_ the structure
was freed already.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch adds in the Xilinx I2C bus driver to some of the
configurations of the timberdale MFD.

It provides the I2C devices to the XIIC via platform data in a
similar way as done to the ocores driver.
Signed-off-by: NRichard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

We should check for pdata being not NULL before dereferencing it.
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add support for the Texas Instruments TMP105 temperature sensor
device.
Signed-off-by: NShubhrajyoti Datta <shubhrajyoti@ti.com>
Acked-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Read only one of the GPIO pins as an analog voltage. The ADC can be
switched to a different GPIO pin at runtime, but this is not supported.

Previously, this driver would report the analog voltage of the currently
selected GPIO pin as all three GPIO voltages: in9_input, in10_input and
in11_input.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org

Add support for the hardware monitoring capabilities of the SCH5127
chip to the dme1737 driver.
Signed-off-by: NJuerg Haefliger <juergh@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Tested-by: NJeff Rickman <jrickman@myamigos.us>

Only stop the chip at driver exit if it was stopped when driver was
loaded. Leave it running otherwise.

Also restore the device configuration if probe failed, to not leave
the system in a dangling state.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Steven King <sfking@fdwdc.com>

Suspend and resume functions shouldn't overwrite the configuration
register. They should only alter the one bit they have to touch.

Also don't assume that register reads and writes always succeed.
Handle errors properly, shall they happen.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Steven King <sfking@fdwdc.com>

Fixes from my driver review:
http://lists.lm-sensors.org/pipermail/lm-sensors/2010-March/028051.html

Only the small changes are in there, more important changes will come
later separately as time permits.

* Drop the remnants of the now gone detect function
* The TMP102 has no known compatible chip
* Include the right header files
* Clarify why byte swapping of register values is needed
* Strip resolution info bit from temperature register value
* Set cache lifetime to 1/3 second
* Don't arbitrarily reject limit values; clamp as needed
* Make limit writing unconditional
* Don't check for transaction types the driver doesn't use
* Properly check for error when setting configuration
* Report error on failed probe
* Make the driver load automatically where needed
* Various other minor fixes
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Steven King <sfking@fdwdc.com>

Driver for the TI TMP102.

The TI TMP102 is similar to the LM75.  It differs from the LM75 by
having a 16-bit conf register and the temp registers have a minimum
resolution of 12 bits; the extended conf register can select 13-bit
resolution (which this driver does) and also change the update rate
(which this driver currently doesn't use).

[JD: Fix tmp102_exit tag, must be __exit, not __init.]
Signed-off-by: NSteven King <sfking@fdwdc.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Provides support for the EMC1403 thermal sensor. Only reporting of values
is supported. The various Moorestown specific extras to do with thermal
alerts and the like are not in this version of the driver.

Considerably edited and tidied up by Alan Cox, plus fixes and detection
bits from Jean Delvare.
Signed-off-by: NKalhan Trisal <kalhan.trisal@intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The Apple SMC uses a systematic labeling scheme for the hardware
temperature sensors. This scheme is currently hidden from
userland. Since the sensor set, and consequently the numbering,
differs between models, an extensive database of configurations is
required for an application such as fan control. This patch adds the
SMC labels to the hwmon sysfs interface, allowing applications to use
the sensors more intelligibly.

[rydberg@euromail.se: fixed error handling]
Signed-off-by: NAlex Murray <murray.alex@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This patch adds generic support for the MacBook Pro 7 family
based on the 7,1 model.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This patch adds generic support for the MacBook Pro 6 family
based on the 6,2 model.

[rydberg@euromail.se: patch cleanup]
Signed-off-by: NBernhard Froemel <froemel@vmars.tuwien.ac.at>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The MacBookPro 5,3 model has two fans, whereas the 5,4 model has
only one. This patch adds explicit support for the 5,3 and 5,4 models.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NAndre Prendel <andre.prendel@gmx.de>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>