The only function of these 'prepare' and 'complete' is to
disable the 'card detect' irq during suspend.

The commit which added this,
commit a48ce884
    mmc: omap_hsmmc: Introduce omap_hsmmc_prepare/complete

justified it by the need to avoid the registration of new devices
during suspend.
However mmc_pm_notify will set ->rescan_disable in the 'prepare'
stage and clear it in the 'complete' stage, so no card detection
will actually happen.
Also the interrupt will be disabled before final suspend as part
of common suspend processing.

So this disabling of the interrupt is unnecessary, and interferes
with a transition to using common code for card-detect management.

Cc: Felipe Balbi <balbi@ti.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Fix returning IRQ_HANDLED with spin_lock held.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The commit 0718e59a ("mmc: sdhci: move FSL ESDHC reset handling quirk into
esdhc code") states that Freescale esdhc is the only controller which needs
the interrupt registers restored after a reset. So it moves
SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET quirk handling code into the
esdhc-imx driver only. Unfortunately the same controller is used in
other boards which use the of-esdhc driver instead (like powerpc P2020).

Restore interrupts after reset in the sdhci-of-esdhc driver also.
Signed-off-by: NAlessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add manual tuning function in CSR atlas7 SoC. It is mainly used
for the UHS-I SD card working SDR50 SDR104 mode.

The tuning principle can be seen in SD spec part1 v3.01 4.2.4.5
(tuning command).

SD host send the cmd19 and set the delay value(0-127).
and the sdcard return 64 bytes data. If the data is same with
the tuning data. The delay value is valid. Execute this commmand
128 times. And calculate the longest window of the valid values.
The value in the middle of this window is the best value.
Signed-off-by: NMinda Chen <Minda.Chen@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We're running into cases where our enabling of the SDIO interrupt in
dw_mmc doesn't actually take effect.  Specifically, adding patch like
this:

 +++ b/drivers/mmc/host/dw_mmc.c
 @@ -1076,6 +1076,9 @@ static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb)

      mci_writel(host, INTMASK,
           (int_mask | SDMMC_INT_SDIO(slot->id)));
 +    int_mask = mci_readl(host, INTMASK);
 +    if (!(int_mask & SDMMC_INT_SDIO(slot->id)))
 +      dev_err(&mmc->class_dev, "failed to enable sdio irq\n");
    } else {

...actually triggers the error message.  That's because the
dw_mci_enable_sdio_irq() unsafely does a read-modify-write of the
INTMASK register.

We can't just use the standard host->lock since that lock is not irq
safe and mmc_signal_sdio_irq() (called from interrupt context) calls
dw_mci_enable_sdio_irq().  Add a new irq-safe lock to protect INTMASK.

An alternate solution to this is to punt mmc_signal_sdio_irq() to the
tasklet and then protect INTMASK modifications by the standard host
lock.  This seemed like a bit more of a high-latency change.
Reported-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In the patch (9623b5b9 mmc: dw_mmc: Disable low power mode if SDIO
interrupts are used) I added code that disabled the low power mode of
dw_mmc when SDIO interrupts are used.  That code worked but always
felt a little hacky because we ended up disabling low power as a side
effect of the first enable_sdio_irq() call.  That wouldn't be so bad
except that disabling low power involves a complicated process of
writing to the CMD/CMDARG registers and that extra process makes it
difficult to cleanly the read-modify-write race in
dw_mci_enable_sdio_irq() (see future patch in the series).

Change the code to take advantage of the init_card() callback of the
mmc core to do this right at bootup.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Host controllers lacking the required internal vmmc regulator may still
follow the spec with regard to the LSB of SDHCI_POWER_CONTROL.  Set the
SDHCI_POWER_ON bit when vmmc is enabled to encourage the controller to
to drive CMD, DAT, SDCLK.

This fixes a regression observed on some Qualcomm and Nvidia boards
caused by 52221610 mmc: sdhci: Improve external VDD regulator support.

Fixes: 52221610 (mmc: sdhci: Improve external VDD regulator support)
Signed-off-by: NTim Kryger <tim.kryger@gmail.com>
Tested-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add PCI IDs for SPT eMMC, SDIO and SD card.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add ACPI HID INT344D for an Intel SDIO host controller.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Sleep in atomic context happened on Trats2 board after inserting or
removing SD card because mmc_gpio_get_cd() was called under spin lock.

Fix this by moving card detection earlier, before acquiring spin lock.
The mmc_gpio_get_cd() call does not have to be protected by spin lock
because it does not access any sdhci internal data.
The sdhci_do_get_cd() call access host flags (SDHCI_DEVICE_DEAD). After
moving it out side of spin lock it could theoretically race with driver
removal but still there is no actual protection against manual card
eject.

Dmesg after inserting SD card:
[   41.663414] BUG: sleeping function called from invalid context at drivers/gpio/gpiolib.c:1511
[   41.670469] in_atomic(): 1, irqs_disabled(): 128, pid: 30, name: kworker/u8:1
[   41.677580] INFO: lockdep is turned off.
[   41.681486] irq event stamp: 61972
[   41.684872] hardirqs last  enabled at (61971): [<c0490ee0>] _raw_spin_unlock_irq+0x24/0x5c
[   41.693118] hardirqs last disabled at (61972): [<c04907ac>] _raw_spin_lock_irq+0x18/0x54
[   41.701190] softirqs last  enabled at (61648): [<c0026fd4>] __do_softirq+0x234/0x2c8
[   41.708914] softirqs last disabled at (61631): [<c00273a0>] irq_exit+0xd0/0x114
[   41.716206] Preemption disabled at:[<  (null)>]   (null)
[   41.721500]
[   41.722985] CPU: 3 PID: 30 Comm: kworker/u8:1 Tainted: G        W      3.18.0-rc5-next-20141121 #883
[   41.732111] Workqueue: kmmcd mmc_rescan
[   41.735945] [<c0014d2c>] (unwind_backtrace) from [<c0011c80>] (show_stack+0x10/0x14)
[   41.743661] [<c0011c80>] (show_stack) from [<c0489d14>] (dump_stack+0x70/0xbc)
[   41.750867] [<c0489d14>] (dump_stack) from [<c0228b74>] (gpiod_get_raw_value_cansleep+0x18/0x30)
[   41.759628] [<c0228b74>] (gpiod_get_raw_value_cansleep) from [<c03646e8>] (mmc_gpio_get_cd+0x38/0x58)
[   41.768821] [<c03646e8>] (mmc_gpio_get_cd) from [<c036d378>] (sdhci_request+0x50/0x1a4)
[   41.776808] [<c036d378>] (sdhci_request) from [<c0357934>] (mmc_start_request+0x138/0x268)
[   41.785051] [<c0357934>] (mmc_start_request) from [<c0357cc8>] (mmc_wait_for_req+0x58/0x1a0)
[   41.793469] [<c0357cc8>] (mmc_wait_for_req) from [<c0357e68>] (mmc_wait_for_cmd+0x58/0x78)
[   41.801714] [<c0357e68>] (mmc_wait_for_cmd) from [<c0361c00>] (mmc_io_rw_direct_host+0x98/0x124)
[   41.810480] [<c0361c00>] (mmc_io_rw_direct_host) from [<c03620f8>] (sdio_reset+0x2c/0x64)
[   41.818641] [<c03620f8>] (sdio_reset) from [<c035a3d8>] (mmc_rescan+0x254/0x2e4)
[   41.826028] [<c035a3d8>] (mmc_rescan) from [<c003a0e0>] (process_one_work+0x180/0x3f4)
[   41.833920] [<c003a0e0>] (process_one_work) from [<c003a3bc>] (worker_thread+0x34/0x4b0)
[   41.841991] [<c003a3bc>] (worker_thread) from [<c003fed8>] (kthread+0xe4/0x104)
[   41.849285] [<c003fed8>] (kthread) from [<c000f268>] (ret_from_fork+0x14/0x2c)
[   42.038276] mmc0: new high speed SDHC card at address 1234
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 94144a46 ("mmc: sdhci: add get_cd() implementation")
Cc: <stable@vger.kernel.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In commit 5491ce3f ("mmc: sdhci-pxav3: add support for the Armada
38x SDHCI controller"), the sdhci-pxav3 driver was extended to include
support for the SDHCI controller found in the Armada 38x
processor. This mainly involved adding some MBus window related
configuration.

However, this configuration is currently done too early in ->probe():
it is done before clocks are enabled, while this configuration
involves touching the registers of the controller, which will hang the
SoC if the clock is disabled. It wasn't noticed until now because the
bootloader typically leaves gatable clocks enabled, but in situations
where we have a deferred probe (due to a CD GPIO that cannot be taken,
for example), then the probe will be re-tried later, after a clock
disable has been done in the exit path of the failed probe attempt of
the device. This second probe() will hang the system due to the clock
being disabled.

This can for example be produced on Armada 385 GP, which has a CD GPIO
connected to an I2C PCA9555. If the driver for the PCA9555 is not
compiled into the kernel, then we will have the following sequence of
events:

  1. The SDHCI probes
  2. It does the MBus configuration (which works, because the clock is
     left enabled by the bootloader)
  3. It enables the clock
  4. It tries to get the CD GPIO, which fails due to the driver being
     missing, so -EPROBE_DEFER is returned.
  5. Before returning -EPROBE_DEFER, the driver cleans up what was
     done, which includes disabling the clock.
  6. Later on, the SDHCI probe is tried again.
  7. It does the MBus configuration, which hangs because the clock is
     no longer enabled.

This commit does the obvious fix of doing the MBus configuration after
the clock has been enabled by the driver.

Fixes: 5491ce3f ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Re-tuning for HS400 mode must be done in HS200
mode. Currently there is no support for that.
That needs to be reflected in the code.
Specifically, if tuning is executed in HS400 mode
then return an error, and do not start the
tuning timer if HS200 tuning is being done prior
to switching to HS400.

Note that periodic re-tuning is not expected
to be needed for HS400 but re-tuning is still
needed after the host controller has lost power.
In the case of suspend/resume that is not necessary
because the card is fully re-initialised. That
just leaves runtime suspend/resume with no support
for HS400 re-tuning.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The tuning timer is always used if the tuning mode
is 1 and there is a tuning count, irrespective of
whether this is the first call, or any subsequent
call. Consequently the logic to start the timer
can be simplified.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NAaron Lu <aaron.lu@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

A 'goto' can be used to save duplicating unlocking
and returning.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NAaron Lu <aaron.lu@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Re-tuning requires that the maximum data length
is limited to 4MiB. The code currently changes
max_blk_count in an attempt to achieve that.
This is wrong because max_blk_count is a different
limit, but it is also un-necessary because
max_req_size is 512KiB anyway. Consequently, the
changes to max_blk_count are removed and the
comment for max_req_size adjusted accordingly.
The comment is also tweaked to show that the 512KiB
limit is a SDMA limit not an ADMA limit.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NAaron Lu <aaron.lu@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The currently used SET_PM_RUNTIME_PM_OPS() macro is defined to the
SET_RUNTIME_PM_OPS() macro. Convert to the later, since that's the
proper one to use.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Instead of having a local hack taking care of sending the tuning
command and as well to verify the response pattern, let's convert to
the common mmc_send_tuning() API instead.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NGeorgi Djakov <gdjakov@mm-sol.com>
Acked-by: NGeorgi Djakov <gdjakov@mm-sol.com>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>

Instead of having a local function taking care of sending the tuning
command, let's use the common mmc_send_tuning() API provided by the mmc
core. In this way the request will be handled as any other request by
sdhci core.

As an effect of this change, the pm_runtime_get_sync() call at
esdhc_prepare_tuning() isn't needed any more.

This patch will also introduce another change in behavior, since before
the response pattern to the tuning command wasn't verified by
sdhci-esdhc-imx. The mmc_send_tuning() does that.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NDong Aisheng <b29396@freescale.com>
Acked-by: NDong Aisheng <b29396@freescale.com>

After commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.

Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/mmc/.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>

The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.

However, after commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.

For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Intel host controllers are capable of doing the bus
width test and of waiting while busy, so add the
capability flags.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

BYT host controllers are capable of doing the bus
width test and of waiting while busy, so add the
capability flags.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC actually causes
standard-compliant behaviour by causing the flagging
of the last DMA transfer descriptor as the end
instead of there being an additional nop descriptor
which is flagged as the end.  Consequently, it is
better to have the quirk.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC actually causes
standard-compliant behaviour by causing the flagging
of the last DMA transfer descriptor as the end
instead of there being an additional nop descriptor
which is flagged as the end.  Consequently, it is
better to have the quirk.  Add it for BYT.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Return probe defer if requesting a dma channel without a dma controller
probed.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

No more use late initcall to manage probing order. Use probe deferring
if needed.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Using __init/__exit attributes can cause several breakages so remove
them.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

All devices with a DMA controller are DT compliant and legacy support
has been removed. For those reasons, some DMA stuff is useless.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The commit, mmc: omap: clarify DDR timing mode between SD-UHS and eMMC,
switched omap_hsmmc to support MMC DDR mode instead of UHS DDR50 mode.

Add UHS DDR50 mode again and this time let's also keep the MMC DDR mode.

Fixes: 5438ad95 (mmc: omap: clarify DDR timing mode between SD-UHS and eMMC)
Reported-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

clk_prepare_enable() may fail and in this case we should propagate the error.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If platform_get_irq() fails, it is better to propagate the real error value
instead of a 'fake' one.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

devm_ioremap_resource() already checks if 'iores' is NULL or not, so we can
skip this manual check.

While at it, move platform_get_resource() closer to devm_ioremap_resource() for
better readability.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add support for the DW MMC host found on the Imagination Pistachio SoC.
Like the DW MMC hosts found on SOCFPGA and Rockchip SoCs, the DW MMC
host on Pistachio requires the use of SDMMC_CMD_USE_HOLD_REG.
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

By using SIMPLE_DEV_PM_OPS we can make the code smaller and cleaner.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Instead of registering the irq name with the driver's name, it's better to pass
the device name so that we have a more explicit indication as to what mmc
instance the irq is related:

$ cat /proc/interrupts
           CPU0
...
 26:          6         -  96  80010000.ssp
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Commit f1d2736c (mmc: dw_mmc: control card read threshold) added
dw_mci_ctrl_rd_thld() with an unconditional write to the CDTHRCTL
register at offset 0x100. However before version 240a, the FIFO region
started at 0x100, so the write messes with the FIFO and completely
breaks the driver.

If the version id < 240A, return early from dw_mci_ctl_rd_thld() so as
not to hit this problem.

Fixes: f1d2736c (mmc: dw_mmc: control card read threshold)
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.13+
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We check for NULL pointers after dereferencing so it's too late.  Oddly
enough, Smatch misses this code but complains about the caller passing
NULL pointers to this function:

	drivers/mmc/host/toshsd.c:389 toshsd_irq()
	error: we previously assumed 'host->cmd' could be null (see line 349)
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

All boards with a dma controller have DT support so using
dma_request_slave_channel_compat is no more needed.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The bit of sdio interrupt is 16 in designware implementation,
but it is 24 on Rockchip SoCs.This patch add sdio_id0 for the
number of slot0 in the SDIO interrupt registers.
Signed-off-by: NAddy Ke <addy.ke@rock-chips.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>