While decoding (MPEG or YUV) is active or when VBI output is in use, then
do not clear the VBI output of the saa7127. Only after the last user is
gone can we clear it.

This fixes the case where playback was stopped, another channel was chosen
and playback was restarted, while /dev/vbi16 was used to set the WSS
(widescreen) setting. Without this fix the WSS was reset on every stop
instead of just keeping the last value.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

First try polling for the result of a mailbox command, then
switch to a test/sleep loop. Also reduce the sleep time from 10 ms
to 1 ms. Improves the responsiveness of the mailbox handling.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Pausing a decoder followed by a Play command would do nothing. Fixed.
Pausing a decoder running at non-standard speed following by a Continue
would reset the speed to 100%. Fixed.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

s_register was assigning the return code to (unsigned)reg->val, rather than
errCode, which it what it would return.  Except reg->val can't be < 0, so it
would never actually return an error.

g_register never actually put the value it read into reg->val.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Various gpio and mux settings for the Osprey 440 weren't correct.  Fix them
and provide some documentation about how the gpios work.

The osprey eeprom routine wasn't run for the 440, add it.  It was also crap,
re-written to be better.

Add the Osprey 440 to the Bt878 ALSA driver's whitelist.  Currently the sample
rate is fixed at 32kHz, as the driver doesn't support different rates for
digital input mode, though the card can select the rate from 32, 44.1, or 48
kHz via gpio.

Setting the audio gain via ALSA isn't supported yet; a userspace tool that
programs the X9221 via i2c-dev must be used.

The Bt878 digital audio format isn't programmed correctly for the CS5331A ADC
used, resulting in extremely garbled sound.  That is fixed in a followup
patch.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When raw capture was turned off, the current capturing frame (v4l_grab_frame)
wasn't reset to NO_GRAB_ACTIVE.  If capture was turned back on, the driver
would think this frame was currently being captured, and wait for it to
complete before starting a new frame.  The hardware on the other hand would
not be actively capturing a frame.  The result was the driver would wait
forever for v4l_grab_frame to be captured.

Some calls to zr36057_set_memgrab(0) were missing spin-locks, which have been
added.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Acked-by: NRonald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add support for the UYVY and the other big endian output formats.  The
driver was naming formats based on the host endianess.  This is different
that all the other drivers appear to work and not what software appears
to expect.

Use ARRAY_SIZE() to find the the size of the zoran_formats array.

Change the way the driver handles setting the video format register.  Rather
than use some if and switch statements to set to register by looking at the
format id, the format list simply has a field with the proper bits to set.

Adds a bit of ifdef to make a driver without V4L1 support more possible.
Also create a macro for defining formats that handles vl41 and/or vl42
support to avoid repeated ifdefs in the format list.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Acked-by: NRonald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The driver was returning the size of the (fixed) buffer it allocated as the
sizeimage field in the v4l2 pixel format, rather than the actual size of the
image.  For example, a 192x128 YUYV image is 49152 bytes but the driver would
always return 131072 bytes since if that was the size of the v4l buffer.

This violates the v4l2 spec, which says that sizeimage should be the actual
size of the image for uncompressed formats.  It also caused mplayer to crash.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Acked-by: NRonald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

During uncompressed capture, the poll() function was looking the wrong frame.
It was using the frame the driver was going to capture into next (pend_tail),
when it should have been looking at the next frame to be de-queued with
DQBUF/SYNC (sync_tail).

It also wasn't looking in the right spot.  It was looking at the file handle's
copy of the buffer status, rather than the driver core copy.  The interrupt
routine marks frames as done in the driver core copy, the file handle copy
isn't updated.  So even if poll() looked at the right frame, it would never
see it transition to done and return POLLIN.

The compressed capture code has this same problem, looking in fh->jpg_buffers
when it should have used zr->jpg_buffers.

There was some logic to detect when there was no current capture in process
nor any frames queued and try to return an error, which ends up being a bad
idea.  It's possible to call select() from one thread while no capture is in
process, or no frames queued, and then start a capture or queue frames from
another thread.

The buffer state variables are protected by a spin lock, which the code wasn't
acquiring.  That is fixed too.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Acked-by: NRonald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The zr36067 driver doesn't make a distinction between the different sub-types
of NTSC, PAL, or SECAM norms.  For example, when the enum std ioctl returns
the PAL standard it returns PAL_BG|PAL_DK|PAL_H|PAL_I.

When setting the norm, it required the bitmask to match exactly the set of
norms used during the enumeration.  If just one norm was specified, for
example PAL_BG or NTSC_M, it would fail.  This violates the V4L2 spec,
"VIDIOC_S_STD accepts *one* or more flags..."

The key thing to realize is that V4L2_STD_PAL is not one bit, it is multiple
bits.  It's ok to call S_STD with any *one* of those bits, but the driver was
requiring *all* of them.

This fixes the S_STD function so that it will accept any set of one or more
PAL norms as PAL, and the same for NTSC and SECAM.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Acked-by: NRonald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Added code to recognize the second interface on M5275 boards.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On the MCF5272, there is no need to read the ICR before writing it :
the bit 4n+3 is a write-enable for the bits 4n,4n+1 and 4n+2.
Signed-off-by: NPhilippe De Muyter <phdm@macqel.be>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the work queue code in the FEC driver.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Removed unused CONFIG symbol and its conditional code from FEC driver.
Pointed out by Robert P. J. Day <rpjday@mindspring.com>.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Include cacheflush.h to get definitions for cache functions used
in this code.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

They are handled in a ->compat_ioctl() handler, so it's just noise
when compat_ioctl.c warns which occurs when they are used on non-SBUS
framebuffer devices.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fully unify all of the DMA ops so that subordinate bus types to
the DMA operation providers (such as ebus, isa, of_device) can
work transparently.

Basically, we just make sure that for every system device we
create, the dev->archdata 'iommu' and 'stc' fields are filled
in.

Then we have two platform variants of the DMA ops, one for SUN4U which
actually programs the real hardware, and one for SUN4V which makes
hypervisor calls.

This also fixes the crashes in parport_pc on sparc64, reported by
Meelis Roos.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All of these drivers use a silly:

struct all_info {
	struct fb_info info;
	struct foo_par par;
};

struct all_info *all = kzalloc(sizeof(*all), GFP_KERNEL);
all->info.par = &all->par;

etc. etc. code sequence, basically replicating the provided
framebuffer_alloc()/framebuffer_release(), and doing it badly.

Not only is this massive code duplication, it also caused a
bug in that we weren't setting the fb_info->device pointer
which results in an OOPS when fb_is_primary_device() runs.

Fix all of this by using framebuffer_{alloc,release}() and
passing in "&of_device->dev" as the device pointer.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Gabriel C reports lguest doesn't compile with CONFIG_BLOCK=n.  Fix this
by introducing a config var for the block device, which depends on
LGUEST && BLOCK.  Do the same for the net driver, rather then depending
gratuitously on CONFIG_NET.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Cc: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove fs.h from mm.h. For this,
 1) Uninline vma_wants_writenotify(). It's pretty huge anyway.
 2) Add back fs.h or less bloated headers (err.h) to files that need it.

As result, on x86_64 allyesconfig, fs.h dependencies cut down from 3929 files
rebuilt down to 3444 (-12.3%).

Cross-compile tested without regressions on my two usual configs and (sigh):

alpha              arm-mx1ads        mips-bigsur          powerpc-ebony
alpha-allnoconfig  arm-neponset      mips-capcella        powerpc-g5
alpha-defconfig    arm-netwinder     mips-cobalt          powerpc-holly
alpha-up           arm-netx          mips-db1000          powerpc-iseries
arm                arm-ns9xxx        mips-db1100          powerpc-linkstation
arm-assabet        arm-omap_h2_1610  mips-db1200          powerpc-lite5200
arm-at91rm9200dk   arm-onearm        mips-db1500          powerpc-maple
arm-at91rm9200ek   arm-picotux200    mips-db1550          powerpc-mpc7448_hpc2
arm-at91sam9260ek  arm-pleb          mips-ddb5477         powerpc-mpc8272_ads
arm-at91sam9261ek  arm-pnx4008       mips-decstation      powerpc-mpc8313_rdb
arm-at91sam9263ek  arm-pxa255-idp    mips-e55             powerpc-mpc832x_mds
arm-at91sam9rlek   arm-realview      mips-emma2rh         powerpc-mpc832x_rdb
arm-ateb9200       arm-realview-smp  mips-excite          powerpc-mpc834x_itx
arm-badge4         arm-rpc           mips-fulong          powerpc-mpc834x_itxgp
arm-carmeva        arm-s3c2410       mips-ip22            powerpc-mpc834x_mds
arm-cerfcube       arm-shannon       mips-ip27            powerpc-mpc836x_mds
arm-clps7500       arm-shark         mips-ip32            powerpc-mpc8540_ads
arm-collie         arm-simpad        mips-jazz            powerpc-mpc8544_ds
arm-corgi          arm-spitz         mips-jmr3927         powerpc-mpc8560_ads
arm-csb337         arm-trizeps4      mips-malta           powerpc-mpc8568mds
arm-csb637         arm-versatile     mips-mipssim         powerpc-mpc85xx_cds
arm-ebsa110        i386              mips-mpc30x          powerpc-mpc8641_hpcn
arm-edb7211        i386-allnoconfig  mips-msp71xx         powerpc-mpc866_ads
arm-em_x270        i386-defconfig    mips-ocelot          powerpc-mpc885_ads
arm-ep93xx         i386-up           mips-pb1100          powerpc-pasemi
arm-footbridge     ia64              mips-pb1500          powerpc-pmac32
arm-fortunet       ia64-allnoconfig  mips-pb1550          powerpc-ppc64
arm-h3600          ia64-bigsur       mips-pnx8550-jbs     powerpc-prpmc2800
arm-h7201          ia64-defconfig    mips-pnx8550-stb810  powerpc-ps3
arm-h7202          ia64-gensparse    mips-qemu            powerpc-pseries
arm-hackkit        ia64-sim          mips-rbhma4200       powerpc-up
arm-integrator     ia64-sn2          mips-rbhma4500       s390
arm-iop13xx        ia64-tiger        mips-rm200           s390-allnoconfig
arm-iop32x         ia64-up           mips-sb1250-swarm    s390-defconfig
arm-iop33x         ia64-zx1          mips-sead            s390-up
arm-ixp2000        m68k              mips-tb0219          sparc
arm-ixp23xx        m68k-amiga        mips-tb0226          sparc-allnoconfig
arm-ixp4xx         m68k-apollo       mips-tb0287          sparc-defconfig
arm-jornada720     m68k-atari        mips-workpad         sparc-up
arm-kafa           m68k-bvme6000     mips-wrppmc          sparc64
arm-kb9202         m68k-hp300        mips-yosemite        sparc64-allnoconfig
arm-ks8695         m68k-mac          parisc               sparc64-defconfig
arm-lart           m68k-mvme147      parisc-allnoconfig   sparc64-up
arm-lpd270         m68k-mvme16x      parisc-defconfig     um-x86_64
arm-lpd7a400       m68k-q40          parisc-up            x86_64
arm-lpd7a404       m68k-sun3         powerpc              x86_64-allnoconfig
arm-lubbock        m68k-sun3x        powerpc-cell         x86_64-defconfig
arm-lusl7200       mips              powerpc-celleb       x86_64-up
arm-mainstone      mips-atlas        powerpc-chrp32
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Restore the 2.6.22 CONFIG_ACPI_SLEEP build option, but now shadowing the
new CONFIG_PM_SLEEP option.
Signed-off-by: NLen Brown <len.brown@intel.com>
[ Modified to work with the PM config setup changes. ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Introduce CONFIG_SUSPEND representing the ability to enter system sleep
states, such as the ACPI S3 state, and allow the user to choose SUSPEND
and HIBERNATION independently of each other.

Make HOTPLUG_CPU be selected automatically if SUSPEND or HIBERNATION has
been chosen and the kernel is intended for SMP systems.

Also, introduce CONFIG_PM_SLEEP which is automatically selected if
CONFIG_SUSPEND or CONFIG_HIBERNATION is set and use it to select the
code needed for both suspend and hibernation.

The top-level power management headers and the ACPI code related to
suspend and hibernation are modified to use the new definitions (the
changes in drivers/acpi/sleep/main.c are, mostly, moving code to reduce
the number of ifdefs).

There are many other files in which CONFIG_PM can be replaced with
CONFIG_PM_SLEEP or even with CONFIG_SUSPEND, but they can be updated in
the future.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace CONFIG_SOFTWARE_SUSPEND with CONFIG_HIBERNATION to avoid
confusion (among other things, with CONFIG_SUSPEND introduced in the
next patch).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A non-periodic clock_event_device and the "jiffies" clock don't mix well:
tick_handle_periodic() can go into an infinite loop.

Currently lguest guests use the jiffies clock when the TSC is
unusable.  Instead, make the Host write the current time into the lguest
page on every interrupt.  This doesn't cost much but is more precise
and at least as accurate as the jiffies clock.  It also gets rid of
the GET_WALLCLOCK hypercall.

Also, delay setting sched_clock until our clock is set up, otherwise
the early printk timestamps can go backwards (not harmful, just ugly).
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Jason Yeh sent his crashing .config: bzImages made with
CONFIG_RELOCATABLE=y put the relocs where the BSS is expected, and we
crash with unusual results such as:

	lguest: unhandled trap 14 at 0xc0122ae1 (0xa9)

Relying on BSS being zero was merely laziness on my part, and
unfortunately, lguest doesn't go through the normal startup path (which
does this in asm).
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch contains changes in mptctl.c to support logging in MPT fusion drivers

The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
signed-off-by: NSathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch contains changes in mptfc.c, mptlan.c, mptsas.c and mptspi.c to
support logging in MPT fusion drivers.

The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
signed-off-by: NSathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch contains changes in mptscsih.c to support logging in MPT fusion
drivers.

The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h

A new sysfs attribute is added to retrieve and modify the debug level.
signed-off-by: NSathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch contains changes in mptbase.c to support logging in MPT fusion
drivers.

The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h

A new module parameter mpt_debug_level is added to pass the debug level as
module parameter.
signed-off-by: NSathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch adds a new file mptdebug.h in the fusion source directory,
which contains different debug macros.  The existing debug macros and
flags are removed from the mptbase.h and Makefile In Kconfig a new
configuration parameter FUSION_LOGGING is added to enable/disable the
logging support during compile time.
signed-off-by: NSathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

In sas_smp_get_phy_events() we never test if the call to
alloc_smp_req(RPEL_REQ_SIZE) succeeds or fails. That means we run
the risk of dereferencing a NULL pointer if it does fail. Far
better to test if we got NULL back and in that case return -ENOMEM
just as we already do for the other memory allocation in that
function.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The patch is *much* smaller than the description. I am attempting to
answer to those that want to understand an issue that was reported in
May this year.

If a Sunrise Lake based card that requires an alternate reset mechanism
is set up to ignore the commanded IOP_RESET it reports 0x00000010
(IOP_RESET ignored) instead of 0x3803000F (use alternate reset mechanism
to reset all cores), and thus the reset platform function decides to
switch to IOP_RESET_ALWAYS because the reset platform function
parameters indicate that we *need* to reset the card. IOP_RESET_ALWAYS
then responds with the 0x3803000F return code, but alas we treat this as
an error instead of using the alternate reset mechanism (put a 0x03 into
the register offset 0x38). The reset fails, but the fact that the
IOP_RESET_ALWAYS command was issued has put the card in a purposeful
shutdown state in preparation for the alternate hardware reset to be
applied. Yuck.

IOP_RESET is ignored in internal production cards, typically to ensure
that we catch all adapter lockup issues without the driver progressing
further, so this would not appear to be a field issue and thus this
patch was destined to be only in the internal Adaptec source tree.
IOP_RESET_ALWAYS is reserved for
kexec/kdump/FirmwareUpdate/AutomatedTestFrames so we did not function as
expected in any case. Also in the past we have had OEMs specifically
request that cards not be resetable after a BlinkLED/FirmwareAssert for
one reason or another and To head off the possibility that the Sunrise
Lake based cards would suffer a similar fate, we propose the enclosed
fix.

Yinghai Lu of SUN had a pre-production card with IOP_RESET disabled when
he reported an issue to the linux kernel list back in May regarding a
kexec problem resulting from this reset being ignore. His fix was to
update the Firmware to one that did not ignore the IOP_RESET. Previous
kernels did not attempt to reset the adapter and that is why it surfaced
as a regression in his hands.

The current list of aacraid based cards that use Sunrise Lake:

9005:0285:9005:02b5     Adaptec 5445
9005:0285:9005:02b6     Adaptec 5805
9005:0285:9005:02b7     Adaptec 5085
9005:0285:9005:02c3     Adaptec 51205
9005:0285:9005:02c4     Adaptec 51605
9005:0285:9005:02ce     Adaptec 51245
9005:0285:9005:02cf     Adaptec 51645
9005:0285:9005:02d0     Adaptec 52445
9005:0285:9005:02d1     Adaptec 5405
9005:0285:9005:02b8     ICP     ICP5445SL
9005:0285:9005:02b9     ICP     ICP5085SL
9005:0285:9005:02ba     ICP     ICP5805SL
9005:0285:9005:02c5     ICP     ICP5125SL
9005:0285:9005:02c6     ICP     ICP5165SL
9005:0285:108e:7aac     SUN     STK RAID REM
9005:0285:108e:0286     SUN     STK RAID INT
9005:0285:108e:0287     SUN     STK RAID EXT
9005:0285:108e:7aae     SUN     STK RAID EM

All of these are publicly released with IOP_RESET enabled. So there is
no immediate need for this patch.
Signed-off-by: NMark Salyzyn <aacraid@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Customer running an application that issues SYNCHRONIZE_CACHE calls
directly noticed the broad stroke of the current implementation in the
aacraid driver resulting in multiple applications feeding I/O to the
storage causing the issuing application to stall for long periods of
time. By only waiting for the current WRITE commands, rather than all
commands, to complete; and those that are in range of the
SYNCHRONIZE_CACHE call that would associate more tightly with the
issuing application before telling the Firmware to flush it's dirty
cache, we managed to reduce the stalling. The Firmware itself still
flushes all the dirty cache associated with the array ignoring the
range, it just does so in a more timely manner.
Signed-off-by: NMark Salyzyn <aacraid@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

According to http://bugzilla.kernel.org/show_bug.cgi?id=5953, the
easyRAID returns rubbish to REPORT LUNS.

Cc: Natalie Protasevich <protasnb@gmail.com>
Cc: Hans-Christian Armingeon <mog.johnny@gmx.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

 - Run Lindent
 - Move advansys_detect and advansys_release to the end of the file
 - Split advansys_board_found out of advansys_detect
 - Rename a few variables, such as shp to shost and pci_devp to pdev
 - Turn STATIC into static
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Wide transfers are required for every setting of PPR apart from QAS.
It seems the DV code starts at the minimum, which turns on DT and Wide
regardless of the setting of max_width.  Redo the PPR and period
setting routines to respect max_width (i.e. start at period = 10 if it
is zero).

This fixes bugzilla 8366
Acked-by: N"Freels, James D." <freelsjd@ornl.gov>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This is a patch to fix 'segmentation fault' issue which was initiated
by Richard Lary <rlary@us.ibm.com>.  Thanks again Richard.

- on following sysfs attritute function, changes have made so that both
  count and offset input parameters are honored by the functions.
    = qla2x00_sysfs_read_nvram()
    = qla2x00_sysfs_read_vpd()
- made changes so that NVRAM data to be cached to minimize H/W accesses
  during agent querying of the driver's.
Signed-off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Minor unimportant cuttings from the floor bundled in with a version
stamp update. Only controversial change is the dropping of Alan Cox
copyright on the nark.c module since that file has no code written by
him in it.
Signed-off-by: NMark Salyzyn <aacraid@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

It was found by LSI that on setups with large amounts of memory
we were bouncing buffers when we did not need to. If the iscsi tcp
code touches the data buffer (or a helper does),
it will kmap the buffer. iscsi_tcp also does not interact with hardware,
so it does not have any hw dma restrictions. This patch sets the bounce
buffer settings for our device queue so buffers should not be bounced
because of a driver limit.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

We should not be checking the cmd windown for just handling r2t responses.
And if the window closes in on us, always have scsi-ml requeue the command
from our queuecommand function.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>