Use a more current logging style.
Make sure all output is prefixed appropriately.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the POWER_PMI to the op_mode where it is changed.  The trans needs
to check it frequently, so shadow the status in the trans and update it
in trans when it infrequently changes.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The op_mode should check for FW_ERROR before calling send_cmd.  This
removes the need to test for FW_ERROR in the trans layer.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With error logging now completely handled in
the op_mode, the transport layer does not
need to know information about the loaded
firmware.

Remove this state information from the
iwl_shared data structure.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_get_single_channel_number is used only in
iwl-scan.c, move it there and mark it static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_full_rxon_required is used only in
iwl-agn-rxon.c. Move it there and mark it
static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_check_rxon_cmd is used only in
iwl-agn-rxon.c. Move it there and mark it
static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_set_rxon_hwcrypto is used only in
iwl-agn-rxon.c. Move it there and mark it
static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_send_rxon_timing is used only in
iwl-agn-rxon.c, move it there and mark it
static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is used only in one file, move it there
and make it static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This variable holds the ucode currently
running on the device; which is determined by
op_mode, so move this parameter there.

Also, the name of the variable is a bit
misleading, so rename it to cur_ucode.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Error log reporting does not belong to the
transport layer, but to the op_mode loading
the ucode, as it is the entity which knows
about the ucode loaded, and what the error
information means.

Move device logging pointers from the
transport layer to op_mode.

With this change, transport layer only
reports an error to the op_mode, which will
figure out what to do with the error. This
causes the driver to now dump out error logs
when the command queue is stuck as well.

Also, move the debugfs entry for event logs
out of the transport layer and into op_mode.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_nic_error is used in iwl-agn.c only, move
it there and make it static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the process, make iwlagn_fw_error
a non-static function, as it is used
by more than one file.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No other component is accessing it any more,
so it can move to the correct place in priv.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The queue mapping is not only dynamic, it
is also dependent on the uCode, as we can
already see today with the dual-mode and
non-dual-mode being different.

Move the queue mapping out of the transport
layer and let the higher layer manage it.
Part of the transport configuration is how
to set up the queues.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As idle is just a deep powersave mode for
the device, it will easily scan while idle
since that turns off powersave.

This reduces the number of commands sent
to the device when scanning.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is not (no longer?) used by any device
so just remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is used only by 2000 class devices, but
they all use it so remove the configuration
parameter and hard-code the programming.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's no device using this mechanism.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It talks about treating different uCode APIs
as different pieces of hardware which really
isn't how we handle things.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A whole bunch of messages, even some recent ones,
didn't include a trailing newline so add it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The calibration results all come in while we're
waiting for the calibration complete notification.
As a consequence, there's no need to install a
global RX handler for them, we can use the newly
extended notification wait framework for this and
make the code easier to follow.

It is now quite explicit that we are processing
the calibration results while waiting for the
complete notification, before this was implicit
and developers had to know this to understand why
we wait for the calibration complete notification
and what happens while we wait.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sometimes, for example when we ask the uCode
for calibration, we wait for the "complete"
response while we also need the results that
are sent in other, interim, notifications.

Currently we handle this by installing an RX
handler globally, but that isn't needed as
this is the only time we want to use these
notifications.

So in order to be able to simplify at least
future code that does the same, extend the
notification wait framework to allow you to
wait for multiple commands and decide based
on the command whether the wait finished.

While at it, also fix a race that can then
become relevant -- if the wait function has
returned true once it shouldn't be called
again, today this can happen due to races
between the triggering and the wakeup.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The flow handler (hardware) can put multiple
frames into a single RX buffer. To handle
this, walk the RX buffer and check if there
are multiple valid packets in it.

To let the upper layer handle this correctly
introduce rxb_offset() which is needed when
we pass pages to mac80211 -- we need to know
the offset into the page there.

Also change the page handling scheme to use
refcounting. Anyone who needs a page will
"steal" it, which marks it as having been
used & refcounts it. The RX handler then has
to free its own reference and must not reuse
the page.

Finally, do not set the bit asking the FH to
give us each packet in a single buffer. This
really enables the feature.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

get rid of un-needed parameter

Change-Id: I992741e7382a3dbced7f8413bf1d5f301029d576
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add iwl_phy_db structure and API.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It has happened twice now where elaborate troubleshooting has
undergone on systems where CONFIG_CFG80211_INTERNAL_REGDB [0]
has been set but yet net/wireless/db.txt was not updated.

Despite the documentation on this it seems system integrators could
use some more help with this, so throw out a kernel warning at boot time
when their database is empty.

This does mean that the error-prone system integrator won't likely
realize the issue until they boot the machine but -- it does not seem
to make sense to enable a build bug breaking random build testing.

[0] http://wireless.kernel.org/en/developers/Regulatory/CRDA#CONFIG_CFG80211_INTERNAL_REGDB

Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Youngsin Lee <youngsin@qualcomm.com>
Cc: Raja Mani <rmani@qca.qualcomm.com>
Cc: Senthil Kumar Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Vipin Mehta <vipimeht@qca.qualcomm.com>
Cc: yahuan@qca.qualcomm.com
Cc: jjan@qca.qualcomm.com
Cc: vthiagar@qca.qualcomm.com
Cc: henrykim@qualcomm.com
Cc: jouni@qca.qualcomm.com
Cc: athiruve@qca.qualcomm.com
Cc: cjkim@qualcomm.com
Cc: philipk@qca.qualcomm.com
Cc: sunnykim@qualcomm.com
Cc: sskwak@qualcomm.com
Cc: kkim@qualcomm.com
Cc: mattbyun@qualcomm.com
Cc: ryanlee@qualcomm.com
Cc: simbap@qualcomm.com
Cc: krislee@qualcomm.com
Cc: conner@qualcomm.com
Cc: hojinkim@qualcomm.com
Cc: honglee@qualcomm.com
Cc: johnwkim@qualcomm.com
Cc: jinyong@qca.qualcomm.com
Cc: stable@vger.kernel.org
Signed-off-by: NLuis R. Rodriguez <mcgrof@frijolero.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch is intended to solve the follwing issues in RANN propagation:
[1] The interval in propagated RANN should be based on the interval of received RANN.
[2] The aggregated path metric for propagated RANN is as received plus own link metric
    towards the transmitting mesh STA (not root mesh STA).
[3] The comparison of path metric for RANN with same sequence number should be done
    before deciding whether to propagate or not.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current version of rtlwifi for USB operations uses kmalloc to
acquire a 32-bit buffer for each read of the device. When
_usb_read_sync() is called with the rcu_lock held, the result is
a "sleeping function called from invalid context" BUG. This is
reported for two cases in https://bugzilla.kernel.org/show_bug.cgi?id=42775.
The first case has the lock originating from within rtlwifi and could
be fixed by rearranging the locking; however, the second originates from
within mac80211. The kmalloc() call is removed from _usb_read_sync()
by creating a ring buffer pointer in the private area and
allocating the buffer data in the probe routine.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [This version good for 3.3+ - different patch for 3.2 - 2.6.39]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The HWMP sequence number of received RANN element is compared to decide whether to be
propagated. The sequence number is required to covert from 32bit little endian data into
CPUs endianness for comparison. The same applies to the RANN metric.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When receiving DTIM we currently disable power save mode in the
hardware unconditionally, i.e. also when the hardware was not sleeping.
This causes trouble with at least one wireless chipset (Ralink RT3572).
When the hardware is not sleeping and we send a wakeup command (e.g.
this happens after a scan) then a significant decrease of the link
quality or a disconnect may occur.
Disabling power save mode only when it was enabled prevents this issue.
Signed-off-by: NRonald Wahl <ronald.wahl@raritan.com>
Reviewed-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Calling mod_timer from the rx/tx hotpath is somewhat expensive, and the
timeout doesn't need to be so precise.

Switch to a different strategy: Schedule the timer initially, store jiffies
of all last rx/tx activity which would previously modify the timer, and
let the timer re-arm itself after checking the last rx/tx timestamp.
Make the session timers deferrable to avoid causing extra wakeups on systems
running on battery.
This visibly reduces CPU load under high network load on small embedded
systems.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With 9-letter driver names phy's number was truncated
to two characters, which caused warnings when creating
sysfs entries for leds on systems with multiple devices.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Reviewed-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use a temporary to make the code a bit neater.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the normal kernel facilities and use %pM
to print the all zero mac address.

Remove unnecessary line continuation.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: Larry.Finger@lwfinger.net
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drivers that load firmware from their probe routine have problems with
the latest versions of udev as they get timeouts while waiting for user
space to start. The problem is fixed by using request_firmware_nowait()
and delaying the start of mac80211 until the firmware is loaded.

To prevent the possibility of the driver being unloaded while the
firmware loading callback is still active, a completion queue entry
is used.

Also, to simplify the firmware loading procedure, this patch removes
the old, unofficial and confusing fallback firmware names. However,
they are still supported! So any user - who is still using them -
is hereby advised to link/rename their old firmware filenames:
	isl3890usb to isl3886usb
	isl3887usb_bare to isl3887usb
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

p54_unregister_common may now be called by the backend
driver's remove routine, even if the ieee80211_hw device
struct was never successfully registered.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>