With all board files removed, those core functions used for non-DT
boot only can be removed now.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Since DT kernel provides the equivalent support with those board
files, we can remove them now.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Lauri Hintsala <lauri.hintsala@bluegiga.com>

There are some efforts going on to have flexcan_switch function
implemented in flexcan driver, so that this platform function hook
can be saved for device tree boot.  But due to the mx28evk board
design oddness that two flexcan transceivers share one switch gpio,
we have to come up a separate and generic gpio-switch driver to handle
all these gpio switch use cases.

Before that happens, we choose to use auxdata to pass flexcan_switch
function hook, so that the DT conversion is not blocked there.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

For non-DT boot, function tx28_add_fec0 configures all ENET0 pins
into gpio mode for resetting fec phy, and then reconfigures those pins
into ENET function after that.

For DT boot, all the pin configuration is done by pinctrl subsystem.
Ideally, when gpio_request gets called, GPIO subsystem should call
pinctrl to configure pins into gpio mode automatically, and have pins
freed up from pinctrl subsystem when gpio_free is called.  But right
now, this cooperation between gpio and pinctrl hasn't been available.
As the result, we have to explicitly call pinctrl_get_select and
pinctrl_put for device tree boot.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NLothar Waßmann <LW@KARO-electronics.de>

Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Juergen Beisert <jbe@pengutronix.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

There is no need for adding board related entries into dt_board_compat.

Leave only the SoC entry.

This way we do not need to patch a C file when adding dt support for
a new board.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Added missed clkmux setting for mx28evk.

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NDong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add AUART0 support.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

On a 2-node machine with 256GB of ram we get 512 lines of
console output, which is just too much.

This mimicks Yinghai Lu's x86 commit c2b91e2e
(x86_64/mm: check and print vmemmap allocation continuous) except that
we aren't ever going to get contiguous block pointers in between calls
so just print when the virtual address or node changes.

This decreases the output by an order of 16.

Also demote this to KERN_DEBUG.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ntosd2_init_i2c walks the ntosd2_i2c_info array, which it expects to
be populated with at least one member. gcc correctly warns about
the out-of-bounds access here.

Since this can not possibly work, it's better to disable i2c
support entirely on this board.

Without this patch, building davinci_all_defconfig results in:

arch/arm/mach-davinci/board-neuros-osd2.c: In function 'davinci_ntosd2_init':
arch/arm/mach-davinci/board-neuros-osd2.c:187:20: warning: array subscript is above array bounds [-Warray-bounds]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Andrey Porodko <panda@chelcom.ru>

Disabling CONFIG_BUG creates an insane amount of build warnings, which
makes it useless to check for building defconfigs to see if new
warnings show up.

Without this patch, building tct_hammer_defconfig results in:

net/packet/af_packet.c: In function 'tpacket_rcv':
net/packet/af_packet.c:1889:30: warning: 'hdrlen' may be used uninitialized in this function [-Wuninitialized]
net/core/ethtool.c: In function 'ethtool_get_feature_mask':
net/core/ethtool.c:213:1: warning: control reaches end of non-void function [-Wreturn-type]
block/cfq-iosched.c: In function 'cfq_async_queue_prio':
block/cfq-iosched.c:2914:1: warning: control reaches end of non-void function [-Wreturn-type]
mm/bootmem.c: In function 'mark_bootmem':
mm/bootmem.c:352:1: warning: control reaches end of non-void function [-Wreturn-type]
net/core/dev.c: In function 'skb_warn_bad_offload':
net/core/dev.c:1904:33: warning: unused variable 'null_features' [-Wunused-variable]
drivers/mtd/chips/cfi_probe.c: In function 'cfi_chip_setup':
include/linux/mtd/cfi.h:489:3: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized]
include/linux/mtd/map.h:394:11: note: 'r.x[0]' was declared here
include/linux/mtd/cfi.h:489:3: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized]
(and many more)

The size of vmlinux increases by 1.78% because of this:

size obj-arm/vmlinux.nobug
   text    data     bss     dec     hex filename
   2108474  116916   55352 2280742  22cd26 obj-arm/vmlinux
size obj-arm/vmlinux.bug
   text    data     bss     dec     hex filename
   2150804  116916   53696 2321416  236c08 obj-arm/vmlinux
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>

exynos_pm_add_dev_to_genpd is used if one or more out of a large
number of Kconfig symbols are enabled. However the new
exynos_defconfig selects none of those, so the function becomes
unused. Marking it so lets the compiler automatically discard
it.

Without this patch, building exynos_defconfig results in:

arch/arm/mach-exynos/pm_domains.c:118:123: warning: 'exynos_pm_add_dev_to_genpd' defined but not used [-Wunused-function]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>

It is not currently possible to build the gpmi-nand driver without
also building the mxs-dma driver. Clarify this Kconfig and enable
both in the defconfig file so we can build it again with both enabled.

drivers/built-in.o: In function `gpmi_dma_filter':
clk-fixed-factor.c:(.text+0xafc18): undefined reference to `mxs_dma_is_apbh'
make[1]: *** [vmlinux] Error 1
make: *** [sub-make] Error 2
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NDirk Behme <dirk.behme@de.bosch.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>

Without this patch, building integrator_defconfig results in:

arch/arm/mach-integrator/core.c:150:1: warning: data definition has no type or storage class [enabled by default]
arch/arm/mach-integrator/core.c:150:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
arch/arm/mach-integrator/core.c:150:1: warning: parameter names (without types) in function declaration [enabled by default]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>

The samsung PWM driver has moved to the new PWM subsystem, which
changed the Kconfig symbol for that driver, but the rx1950 and
gta02 boards still uses the old one.

Without this patch, building s3c2410_defconfig results in:

arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_lcd_power':
arch/arm/mach-s3c24xx/mach-rx1950.c:430: undefined reference to `pwm_config'
arch/arm/mach-s3c24xx/mach-rx1950.c:431: undefined reference to `pwm_disable'
arch/arm/mach-s3c24xx/mach-rx1950.c:437: undefined reference to `pwm_config'
arch/arm/mach-s3c24xx/mach-rx1950.c:438: undefined reference to `pwm_enable'
arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_backlight_exit':
arch/arm/mach-s3c24xx/mach-rx1950.c:504: undefined reference to `pwm_free'
arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_backlight_init':
arch/arm/mach-s3c24xx/mach-rx1950.c:487: undefined reference to `pwm_request'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reported-by: NTushar Behera <tushar.behera@linaro.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>

The sa1100 definition of the io_p2v macro has changed in v3.6, and this one
file stopped working because of that.

Without this patch, building hackkit_defconfig results in:

arch/arm/mach-sa1100/leds-hackkit.c: In function 'hackkit_leds_event':
arch/arm/mach-sa1100/leds-hackkit.c:39:4: error: implicit declaration of function 'IOMEM' [-Werror=implicit-function-declaration]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>

The EETI touchscreen asserts its IRQ line as soon as it has data in its
internal buffers. The line is automatically deasserted once all data has
been read via I2C. Hence, the driver has to monitor the GPIO line and
cannot simply rely on the interrupt handler reception.

In the current implementation of the driver, irq_to_gpio() is used to
determine the GPIO number from the i2c_client's IRQ value.

As irq_to_gpio() is not available on all platforms, this patch changes
this and makes the driver ignore the passed in IRQ. Instead, a GPIO is
added to the platform_data struct and gpio_to_irq is used to derive the
IRQ from that GPIO. If this fails, bail out. The driver is only able to
work in environments where the touchscreen GPIO can be mapped to an
IRQ.

Without this patch, building raumfeld_defconfig results in:

drivers/input/touchscreen/eeti_ts.c: In function 'eeti_ts_irq_active':
drivers/input/touchscreen/eeti_ts.c:65:2: error: implicit declaration of function 'irq_to_gpio' [-Werror=implicit-function-declaration]
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org (v3.2+)
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Sven Neumann <s.neumann@raumfeld.com>
Cc: linux-input@vger.kernel.org
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>

Commit 3d55c29f "ARM: tegra: harmony: add regulator supply name and its
input supply" was supposed to fix all the problems with regulators on
Harmony. However, it appears that I only tested it when booting using
board files, not when booting using device tree. This change fixes two
problems with regulators when booting using device tree:

1) That patch only created the vdd_sys regulator when booting using a
   board file. Since this is the root of the whole regulator tree, this
   caused no regulators to successfully initialize when booting using
   device tree. The registration of vdd_sys is moved to fix this.

2) When booting use DT, the regulator core sets has_full_constraints,
   which in turn causes the core to turn off any regulators not marked
   as always on. Some of the affected regulators are required for basic
   system operation. To solve this, add always on constraints to all
   relevant regulators. This doesn't affect booting using a board file
   since nothing sets has_full_constraints in that case.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Commit e9da6e99 (ARM: dma-mapping:
remove custom consistent dma region) changed the way atomic allocations
are handled. However, arm_dma_free() was not modified accordingly, and
as a result freeing of atomic allocations does not work correctly when
CMA is disabled. Memory is leaked and following WARNINGs are seen:

[   57.698911] ------------[ cut here ]------------
[   57.753518] WARNING: at arch/arm/mm/dma-mapping.c:263 arm_dma_free+0x88/0xe4()
[   57.811473] trying to free invalid coherent area: e0848000
[   57.867398] Modules linked in: sata_mv(-)
[   57.921373] [<c000d270>] (unwind_backtrace+0x0/0xf0) from [<c0015430>] (warn_slowpath_common+0x50/0x68)
[   58.033924] [<c0015430>] (warn_slowpath_common+0x50/0x68) from [<c00154dc>] (warn_slowpath_fmt+0x30/0x40)
[   58.152024] [<c00154dc>] (warn_slowpath_fmt+0x30/0x40) from [<c000dc18>] (arm_dma_free+0x88/0xe4)
[   58.219592] [<c000dc18>] (arm_dma_free+0x88/0xe4) from [<c008fa30>] (dma_pool_destroy+0x100/0x148)
[   58.345526] [<c008fa30>] (dma_pool_destroy+0x100/0x148) from [<c019a64c>] (release_nodes+0x144/0x218)
[   58.475782] [<c019a64c>] (release_nodes+0x144/0x218) from [<c0197e10>] (__device_release_driver+0x60/0xb8)
[   58.614260] [<c0197e10>] (__device_release_driver+0x60/0xb8) from [<c0198608>] (driver_detach+0xd8/0xec)
[   58.756527] [<c0198608>] (driver_detach+0xd8/0xec) from [<c0197c54>] (bus_remove_driver+0x7c/0xc4)
[   58.901648] [<c0197c54>] (bus_remove_driver+0x7c/0xc4) from [<c004bfac>] (sys_delete_module+0x19c/0x220)
[   59.051447] [<c004bfac>] (sys_delete_module+0x19c/0x220) from [<c0009140>] (ret_fast_syscall+0x0/0x2c)
[   59.207996] ---[ end trace 0745420412c0325a ]---
[   59.287110] ------------[ cut here ]------------
[   59.366324] WARNING: at arch/arm/mm/dma-mapping.c:263 arm_dma_free+0x88/0xe4()
[   59.450511] trying to free invalid coherent area: e0847000
[   59.534357] Modules linked in: sata_mv(-)
[   59.616785] [<c000d270>] (unwind_backtrace+0x0/0xf0) from [<c0015430>] (warn_slowpath_common+0x50/0x68)
[   59.790030] [<c0015430>] (warn_slowpath_common+0x50/0x68) from [<c00154dc>] (warn_slowpath_fmt+0x30/0x40)
[   59.972322] [<c00154dc>] (warn_slowpath_fmt+0x30/0x40) from [<c000dc18>] (arm_dma_free+0x88/0xe4)
[   60.070701] [<c000dc18>] (arm_dma_free+0x88/0xe4) from [<c008fa30>] (dma_pool_destroy+0x100/0x148)
[   60.256817] [<c008fa30>] (dma_pool_destroy+0x100/0x148) from [<c019a64c>] (release_nodes+0x144/0x218)
[   60.445201] [<c019a64c>] (release_nodes+0x144/0x218) from [<c0197e10>] (__device_release_driver+0x60/0xb8)
[   60.634148] [<c0197e10>] (__device_release_driver+0x60/0xb8) from [<c0198608>] (driver_detach+0xd8/0xec)
[   60.823623] [<c0198608>] (driver_detach+0xd8/0xec) from [<c0197c54>] (bus_remove_driver+0x7c/0xc4)
[   61.013268] [<c0197c54>] (bus_remove_driver+0x7c/0xc4) from [<c004bfac>] (sys_delete_module+0x19c/0x220)
[   61.203472] [<c004bfac>] (sys_delete_module+0x19c/0x220) from [<c0009140>] (ret_fast_syscall+0x0/0x2c)
[   61.393390] ---[ end trace 0745420412c0325b ]---

The patch fixes this.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>

The alignment mask is calculated incorrectly. Fixing the calculation
makes strange hangs/lockups disappear during the boot with Amstrad E3
and 3.6-rc1 kernel.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>

Fix dma_contiguous_remap() so that it continues through all the
regions, even after encountering one that is outside lowmem.
Without this change, if you have two CMA regions, the first outside
lowmem and the seocnd inside lowmem, only the second one will get
set up in the MMU. Data written to that region then doesn't get
automatically flushed from the cache into memory.
Signed-off-by: NChris Brand <cbrand@broadcom.com>
[extended patch subject with 'fix' word]
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>

There are two ports that can output the LCD data, therefore
they have to use separate pimux identifiers so we can select
the one we want to use.
Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

When calling request_irq with IRQF_SHARED, the dev cookie must be set
(i.e. non-NULL), otherwise the code rejects it immediately with -EINVAL.
So restore the logic here where we'd pass a pointer to the name as a
dummy unique val.

Otherwise, booting up on my LANDISK system would fail with:
	DMAC Address Error0 request_irq fail

This was introduced in commit 7f47c718.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The native 31 bit and the compat behaviour for the mmap system calls differ:

In native 31 bit mode the passed in address for the mmap system call will be
unmodified passed to sys_mmap_pgoff().
In compat mode however the passed in address will be modified with
compat_ptr() which masks out the most significant bit.

The result is that in native 31 bit mode each mmap request (with MAP_FIXED)
will fail where the most significat bit is set, while in compat mode it
may succeed.

This odd behaviour was introduced with d3815898 "[S390] mmap: add missing
compat_ptr conversion to both mmap compat syscalls".

To restore a consistent behaviour accross native and compat mode this
patch functionally reverts the above mentioned commit.

Cc: stable@vger.kernel.org
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The compat wrappers incorrectly called the non compat versions of
the system process_vm system calls.

Cc: stable@vger.kernel.org
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

There are multiple errors in how sys_32_personality() handles personality
flags stored in top three bytes.

- directly comparing current->personality against PER_LINUX32 doesn't work
  in cases when any of the personality flags stored in the top three bytes
  are used.
- directly forcefully setting personality to PER_LINUX32 or PER_LINUX
  discards any flags stored in the top three bytes

Fix the first one by properly using personality() macro to compare only
PER_MASK bytes.
Fix the second one by setting only the bits that should be set, instead of
overwriting the whole value.
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

It's unused, so remove it.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Just a small typo fix to make lsxl dtbs compile
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Naming of emma-prp related clocks for the i.MX27 is not correct.
Signed-off-by: NJavier Martin <javier.martin@vista-silicon.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add alias for gpio nodes, so that gpio driver can identify the port
number and then specify a sensible gpio base rather than using the
one dynamically allocated by gpio core.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The Integrator timer is using the clock framework to get the
timer frequency, but missed to prepare the clock before enabling.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

With this patch ocotp support will always be build into the kernel on mxs.
Otherwise a DT-only kernel fails to link with:

arch/arm/mach-mxs/mach-mxs.c:169: undefined reference to `mxs_get_ocotp'
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The CONFIG_DEFAULT_MMAP_MIN_ADDR was set to 65536 in mxs_defconfig,
this caused severe breakage of userland applications since the upper
limit for ARM is 32768. By default CONFIG_DEFAULT_MMAP_MIN_ADDR is
set to 4096 and can also be changed via /proc/sys/vm/mmap_min_addr
if needed.

Quoting Russell King [1]:

"4096 is also fine for ARM too. There's not much point in having
defconfigs change it - that would just be pure noise in the config
files."

the CONFIG_DEFAULT_MMAP_MIN_ADDR can be removed from the defconfig
altogether.

This problem was introduced by commit cde7c41f (ARM: configs: add
defconfig for mach-mxs).

[1] http://marc.info/?l=linux-arm-kernel&m=134401593807820&w=2Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Commit 88cde8b7 (ARM: dts: imx: update #interrupt-cells for gpio nodes)
changes gpio #interrupt-cells from 1 to 2 without updating the users.
It causes the gpio irq requesting call failing in client driver's probe
function.

Add the irq type cell for those gpio interrupt users to fix their
driver probe failure.
Reported-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Since commit c7e963f6 (net/smsc911x: Add regulator support), the lan9220
device tree probe fails on imx53-ard board, because the commit makes
VDD33A and VDDVARIO supplies mandatory for the driver.

Add a fixed dummy 3V3 supplying lan9220 to fix the regression.

Cc: stable@vger.kernel.org
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The imx5 common clock migration causes a regression with smsc911x
driver on imx53-ard board, where a smsc lan9220 controller gets
connected on imx53 with EIM interface.  EIM needs clock emi_slow_gate
to be functional.  In the new imx5 clock driver, there is no use count
incremented for the clock by enabling it, so the framework closes the
clock at late init time and makes EIM stop working then.

Enable emi_slow_gate in clock driver initialization to fix the
regression.

Cc: stable@vger.kernel.org
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>

Fix the keypad clock name, in order to fix the following error:

imx-keypad imx-keypad: failed to get keypad clock
imx-keypad: probe of imx-keypad failed with error -2
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org

Fix registers range.

Cc: stable@vger.kernel.org
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Fix registers range.

Cc: stable@vger.kernel.org
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>