This reverts commit b652896b.

Unfortunately this commit prevents multiplatform from booting to
the point where a serial console is available. Revert it while
a solution is sought.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This reverts commit 6dea2c1e.

Unfortunately this commit prevents multiplatform from booting to
the point where a serial console is available. Revert it while
a solution is sought.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Now that the DTS file r8a7790-koelsch.dts can be used with
board-koelsch.c and board-koelsch-reference.c, proceed with removing
r8a7790-koelsch-reference.dts.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Now that the DTS file r8a7790-lager.dts can be used with board-lager.c
and board-lager-reference.c, proceed with removing
r8a7790-lager-reference.dts.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The external crystal frequency is 20MHz on the Koelsch board. Specify it
in the device tree.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The external crystal frequency is 20MHz on the Lager board. Specify it
in the device tree.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Copy the device nodes from Koelsch reference into the Koeslch device
tree file. This will allow us to use a single DTS file regarless of
kernel configuration. In case of legacy C board code the device nodes
may or may not be used, but in the multiplatform case all the DT device
nodes are used.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Copy the device nodes from Lager reference into the Lager device tree
file. This will allow us to use a single DTS file regarless of kernel
configuration. In case of legacy C board code the device nodes may or
may not be used, but in the multiplatform case all the DT device nodes
are used.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Declare all core clocks and DIV6 clocks, as well as all MSTP clocks
currently used by r8a7791 boards.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Reference clocks using a "clocks" property in all nodes corresponding to
devices that require a clock.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Declare all core clocks and DIV6 clocks, as well as all MSTP clocks
currently used by r8a7790 boards.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The board had 4 buttons connected to GPIOs, add a corresponding
gpio-keys device.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The Armadillo 800 EVA panel module has a backlight enable signal
connected to GPIO 61. Report this in the backlight DT node.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Commit 22ceeee1 ("pwm-backlight: Add
power supply support") added a mandatory power supply for the PWM
backlight. Add a fixed 5V regulator and reference it for the backlight
power supply.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The koelsch board uses has an SH ethernet controller which uses a Micrel
phy. Select MICREL_PHY for koelsch if SH_ETH is enabled to make use of the
Micrel-specific phy driver rather than relying on the generic phy driver.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Linux 3.13-rc3

Conflicts:
	drivers/pinctrl/sh-pfc/pfc-r8a7740.c
	drivers/pinctrl/sh-pfc/pfc-sh7372.c

This is a commit from the for-next branch of Linus Walleij's pin control tre
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl.git

It is the oldest commit in that branch that provides the dependencies
needed for SoC changes to the usage of sh-pfc.

When CONFIG_COMMON_CLOCK is enabled, call rcar_gen2_clocks_init() in the
timer init function to initialize the common clock framework before
initializing the clock sources. This will take care of clock
initialization when the r8a779[01] boards will be switched to
multiplatform kernels.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add macros usable by device tree sources to reference r8a7791 clocks by
index.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add macros usable by device tree sources to reference r8a7790 clocks by
index.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Prepare the clock at probe time, as there is no other appropriate place
in the driver where we're allowed to sleep.

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

The PCI sub-system is not enabled by default on ARM and on certain
Renesas devices the build does not select it. This means that there
are configurations that do not allow the AHB-PCI bridge used for the
USB sub-systems to be built.

For the R8A7790, R8A7791 and EMEV-2 select MIGHT_HAVE_PCI to allow the
PCI drivers to be built. Also select MIGHT_HAVE_PCI for the multi-config
where there may be many Reneasas devices selected.
Reviewed-by: NIan Molton <ian.molton@codethink.co.uk>
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The break timer accesses hardware registers and thus requires the port
to be enabled. It currently ensures this by enabling the port at the
beginning of the timer handler, and disabling it at the end. However,
the enable/disable operations call the runtime PM sync functions, which
are not allowed in atomic context. The current situation is thus broken.

This change relies on non-atomic code to enable/disable the port. The
break timer will only be started from the IRQ handler, which already
runs with the port enabled. We just need to ensure that the port won't
be disabled with the timer running, and that's easily done by just
cancelling the timer in the port disable function.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

MSTP clocks are gate clocks controlled through a register that handles
up to 32 clocks. The register is often sparsely populated.

Those clocks are found on Renesas ARM SoCs.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

DIV6 clocks are divider gate clocks controlled through a single
register. The divider is expressed on 6 bits, hence the name, and can
take values from 1/1 to 1/64.

Those clocks are found on Renesas ARM SoCs.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>