Merge commit '70c8f01a' into dt3-base

This is a commit from the for-next branch of Linus Walleij's pin control tre
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl.git

It is the oldest commit in that branch that provides the dependencies
needed for SoC changes to the usage of sh-pfc.

Documentation/devicetree/bindings/pinctrl/fsl,imx25-pinctrl.txt

+* Freescale IMX25 IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+CONFIG bits definition:
+PAD_CTL_HYS			(1 << 8)
+PAD_CTL_PKE			(1 << 7)
+PAD_CTL_PUE			(1 << 6)
+PAD_CTL_PUS_100K_DOWN		(0 << 4)
+PAD_CTL_PUS_47K_UP		(1 << 4)
+PAD_CTL_PUS_100K_UP		(2 << 4)
+PAD_CTL_PUS_22K_UP		(3 << 4)
+PAD_CTL_ODE_CMOS		(0 << 3)
+PAD_CTL_ODE_OPENDRAIN		(1 << 3)
+PAD_CTL_DSE_NOMINAL		(0 << 1)
+PAD_CTL_DSE_HIGH		(1 << 1)
+PAD_CTL_DSE_MAX			(2 << 1)
+PAD_CTL_SRE_FAST		(1 << 0)
+PAD_CTL_SRE_SLOW		(0 << 0)
+
+Refer to imx25-pinfunc.h in device tree source folder for all available
+imx25 PIN_FUNC_ID.

Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt

@@ -52,12 +52,25 @@ Required properties for pin configuration node:
   CONFIG can be 0 or 1, meaning Pullup disable/enable.
 
 
+The iomux controller has gpio child nodes which are embedded in the iomux
+control registers. They have to be defined as child nodes of the iomux device
+node. If gpio subnodes are defined "#address-cells", "#size-cells" and "ranges"
+properties for the iomux device node are required.
 
 Example:
 
 iomuxc: iomuxc@10015000 {
 	compatible = "fsl,imx27-iomuxc";
 	reg = <0x10015000 0x600>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	gpio1: gpio@10015000 {
+		...
+	};
+
+	...
 
 	uart {
 		pinctrl_uart1: uart-1 {
@@ -83,6 +96,15 @@ The above example using macros:
 iomuxc: iomuxc@10015000 {
 	compatible = "fsl,imx27-iomuxc";
 	reg = <0x10015000 0x600>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	gpio1: gpio@10015000 {
+		...
+	};
+
+	...
 
 	uart {
 		pinctrl_uart1: uart-1 {

Documentation/devicetree/bindings/pinctrl/qcom,msm8x74-pinctrl.txt

+Qualcomm MSM8x74 TLMM block
+
+Required properties:
+- compatible: "qcom,msm8x74-pinctrl"
+- reg: Should be the base address and length of the TLMM block.
+- interrupts: Should be the parent IRQ of the TLMM block.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells: Should be two.
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells : Should be two.
+                The first cell is the gpio pin number and the
+                second cell is used for optional parameters.
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Qualcomm's pin configuration nodes act as a container for an abitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+ pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength.
+
+Non-empty subnodes must specify the 'pins' property.
+Note that not all properties are valid for all pins.
+
+
+Valid values for qcom,pins are:
+  gpio0-gpio145
+    Supports mux, bias and drive-strength
+
+  sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data
+    Supports bias and drive-strength
+
+Valid values for qcom,function are:
+  blsp_i2c2, blsp_i2c6, blsp_i2c11, blsp_spi1, blsp_uart2, blsp_uart8, slimbus
+
+  (Note that this is not yet the complete list of functions)
+
+
+
+Example:
+
+	msmgpio: pinctrl@fd510000 {
+		compatible = "qcom,msm8x74-pinctrl";
+		reg = <0xfd510000 0x4000>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupts = <0 208 0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart2_default>;
+
+		uart2_default: uart2_default {
+			mux {
+				qcom,pins = "gpio4", "gpio5";
+				qcom,function = "blsp_uart2";
+			};
+
+			tx {
+				qcom,pins = "gpio4";
+				drive-strength = <4>;
+				bias-disable;
+			};
+
+			rx {
+				qcom,pins = "gpio5";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+		};
+	};

Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt

@@ -26,6 +26,11 @@ Optional properties:
   - #gpio-range-cells: Mandatory when the PFC doesn't handle GPIO, forbidden
     otherwise. Should be 3.
 
+  - interrupts-extended: Specify the interrupts associated with external
+    IRQ pins. This property is mandatory when the PFC handles GPIOs and
+    forbidden otherwise. When specified, it must contain one interrupt per
+    external IRQ, sorted by external IRQ number.
+
 The PFC node also acts as a container for pin configuration nodes. Please refer
 to pinctrl-bindings.txt in this directory for the definition of the term "pin
 configuration node" and for the common pinctrl bindings used by client devices.
@@ -103,6 +108,15 @@ Example 1: SH73A0 (SH-Mobile AG5) pin controller node
 		      <0xe605801c 0x1c>;
 		gpio-controller;
 		#gpio-cells = <2>;
+		interrupts-extended =
+			<&irqpin0 0 0>, <&irqpin0 1 0>, <&irqpin0 2 0>, <&irqpin0 3 0>,
+			<&irqpin0 4 0>, <&irqpin0 5 0>, <&irqpin0 6 0>, <&irqpin0 7 0>,
+			<&irqpin1 0 0>, <&irqpin1 1 0>, <&irqpin1 2 0>, <&irqpin1 3 0>,
+			<&irqpin1 4 0>, <&irqpin1 5 0>, <&irqpin1 6 0>, <&irqpin1 7 0>,
+			<&irqpin2 0 0>, <&irqpin2 1 0>, <&irqpin2 2 0>, <&irqpin2 3 0>,
+			<&irqpin2 4 0>, <&irqpin2 5 0>, <&irqpin2 6 0>, <&irqpin2 7 0>,
+			<&irqpin3 0 0>, <&irqpin3 1 0>, <&irqpin3 2 0>, <&irqpin3 3 0>,
+			<&irqpin3 4 0>, <&irqpin3 5 0>, <&irqpin3 6 0>, <&irqpin3 7 0>;
 	};
 
 Example 2: A GPIO LED node that references a GPIO

drivers/pinctrl/Kconfig

@@ -116,15 +116,22 @@ config PINCTRL_IMX1_CORE
 
 config PINCTRL_IMX27
 	bool "IMX27 pinctrl driver"
-	depends on OF
 	depends on SOC_IMX27
 	select PINCTRL_IMX1_CORE
 	help
 	  Say Y here to enable the imx27 pinctrl driver
 
+
+config PINCTRL_IMX25
+        bool "IMX25 pinctrl driver"
+        depends on OF
+        depends on SOC_IMX25
+        select PINCTRL_IMX
+        help
+          Say Y here to enable the imx25 pinctrl driver
+
 config PINCTRL_IMX35
 	bool "IMX35 pinctrl driver"
-	depends on OF
 	depends on SOC_IMX35
 	select PINCTRL_IMX
 	help
@@ -132,7 +139,6 @@ config PINCTRL_IMX35
 
 config PINCTRL_IMX50
 	bool "IMX50 pinctrl driver"
-	depends on OF
 	depends on SOC_IMX50
 	select PINCTRL_IMX
 	help
@@ -140,7 +146,6 @@ config PINCTRL_IMX50
 
 config PINCTRL_IMX51
 	bool "IMX51 pinctrl driver"
-	depends on OF
 	depends on SOC_IMX51
 	select PINCTRL_IMX
 	help
@@ -148,7 +153,6 @@ config PINCTRL_IMX51
 
 config PINCTRL_IMX53
 	bool "IMX53 pinctrl driver"
-	depends on OF
 	depends on SOC_IMX53
 	select PINCTRL_IMX
 	help
@@ -156,7 +160,6 @@ config PINCTRL_IMX53
 
 config PINCTRL_IMX6Q
 	bool "IMX6Q/DL pinctrl driver"
-	depends on OF
 	depends on SOC_IMX6Q
 	select PINCTRL_IMX
 	help
@@ -164,7 +167,6 @@ config PINCTRL_IMX6Q
 
 config PINCTRL_IMX6SL
 	bool "IMX6SL pinctrl driver"
-	depends on OF
 	depends on SOC_IMX6SL
 	select PINCTRL_IMX
 	help
@@ -172,7 +174,6 @@ config PINCTRL_IMX6SL
 
 config PINCTRL_VF610
 	bool "Freescale Vybrid VF610 pinctrl driver"
-	depends on OF
 	depends on SOC_VF610
 	select PINCTRL_IMX
 	help
@@ -202,6 +203,17 @@ config PINCTRL_IMX28
 	bool
 	select PINCTRL_MXS
 
+config PINCTRL_MSM
+	bool
+	select PINMUX
+	select PINCONF
+	select GENERIC_PINCONF
+
+config PINCTRL_MSM8X74
+	bool "Qualcomm 8x74 pin controller driver"
+	depends on OF && OF_IRQ
+	select PINCTRL_MSM
+
 config PINCTRL_NOMADIK
 	bool "Nomadik pin controller driver"
 	depends on ARCH_U8500 || ARCH_NOMADIK

drivers/pinctrl/Makefile

@@ -34,7 +34,10 @@ obj-$(CONFIG_PINCTRL_IMX6SL)	+= pinctrl-imx6sl.o
 obj-$(CONFIG_PINCTRL_FALCON)	+= pinctrl-falcon.o
 obj-$(CONFIG_PINCTRL_MXS)	+= pinctrl-mxs.o
 obj-$(CONFIG_PINCTRL_IMX23)	+= pinctrl-imx23.o
+obj-$(CONFIG_PINCTRL_IMX25)	+= pinctrl-imx25.o
 obj-$(CONFIG_PINCTRL_IMX28)	+= pinctrl-imx28.o
+obj-$(CONFIG_PINCTRL_MSM)	+= pinctrl-msm.o
+obj-$(CONFIG_PINCTRL_MSM8X74)	+= pinctrl-msm8x74.o
 obj-$(CONFIG_PINCTRL_NOMADIK)	+= pinctrl-nomadik.o
 obj-$(CONFIG_PINCTRL_STN8815)	+= pinctrl-nomadik-stn8815.o
 obj-$(CONFIG_PINCTRL_DB8500)	+= pinctrl-nomadik-db8500.o

drivers/pinctrl/pinconf.c

@@ -28,12 +28,6 @@ int pinconf_check_ops(struct pinctrl_dev *pctldev)
 {
 	const struct pinconf_ops *ops = pctldev->desc->confops;
 
-	/* We must be able to read out pin status */
-	if (!ops->pin_config_get && !ops->pin_config_group_get) {
-		dev_err(pctldev->dev,
-			"pinconf must be able to read out pin status\n");
-		return -EINVAL;
-	}
 	/* We have to be able to config the pins in SOME way */
 	if (!ops->pin_config_set && !ops->pin_config_group_set) {
 		dev_err(pctldev->dev,
@@ -67,9 +61,9 @@ int pin_config_get_for_pin(struct pinctrl_dev *pctldev, unsigned pin,
 	const struct pinconf_ops *ops = pctldev->desc->confops;
 
 	if (!ops || !ops->pin_config_get) {
-		dev_err(pctldev->dev, "cannot get pin configuration, missing "
+		dev_dbg(pctldev->dev, "cannot get pin configuration, missing "
 			"pin_config_get() function in driver\n");
-		return -EINVAL;
+		return -ENOTSUPP;
 	}
 
 	return ops->pin_config_get(pctldev, pin, config);
@@ -93,10 +87,10 @@ int pin_config_group_get(const char *dev_name, const char *pin_group,
 	ops = pctldev->desc->confops;
 
 	if (!ops || !ops->pin_config_group_get) {
-		dev_err(pctldev->dev, "cannot get configuration for pin "
+		dev_dbg(pctldev->dev, "cannot get configuration for pin "
 			"group, missing group config get function in "
 			"driver\n");
-		ret = -EINVAL;
+		ret = -ENOTSUPP;
 		goto unlock;
 	}
 
@@ -305,9 +299,6 @@ static int pinconf_pins_show(struct seq_file *s, void *what)
 	const struct pinconf_ops *ops = pctldev->desc->confops;
 	unsigned i, pin;
 
-	if (!ops || !ops->pin_config_get)
-		return 0;
-
 	seq_puts(s, "Pin config settings per pin\n");
 	seq_puts(s, "Format: pin (name): configs\n");
 
@@ -356,9 +347,6 @@ static int pinconf_groups_show(struct seq_file *s, void *what)
 	unsigned ngroups = pctlops->get_groups_count(pctldev);
 	unsigned selector = 0;
 
-	if (!ops || !ops->pin_config_group_get)
-		return 0;
-
 	seq_puts(s, "Pin config settings per pin group\n");
 	seq_puts(s, "Format: group (name): configs\n");
 

drivers/pinctrl/pinctrl-at91.c

@@ -118,7 +118,7 @@ struct at91_pin_group {
 };
 
 /**
- * struct at91_pinctrl_mux_ops - describes an At91 mux ops group
+ * struct at91_pinctrl_mux_ops - describes an AT91 mux ops group
  * on new IP with support for periph C and D the way to mux in
  * periph A and B has changed
  * So provide the right call back
@@ -722,7 +722,8 @@ static int at91_pinconf_get(struct pinctrl_dev *pctldev,
 	unsigned pin;
 	int div;
 
-	dev_dbg(info->dev, "%s:%d, pin_id=%d, config=0x%lx", __func__, __LINE__, pin_id, *config);
+	*config = 0;
+	dev_dbg(info->dev, "%s:%d, pin_id=%d", __func__, __LINE__, pin_id);
 	pio = pin_to_controller(info, pin_to_bank(pin_id));
 	pin = pin_id % MAX_NB_GPIO_PER_BANK;
 
@@ -1396,7 +1397,7 @@ static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
 	chained_irq_enter(chip, desc);
 	for (;;) {
 		/* Reading ISR acks pending (edge triggered) GPIO interrupts.
-		 * When there none are pending, we're finished unless we need
+		 * When there are none pending, we're finished unless we need
 		 * to process multiple banks (like ID_PIOCDE on sam9263).
 		 */
 		isr = readl_relaxed(pio + PIO_ISR) & readl_relaxed(pio + PIO_IMR);
@@ -1505,7 +1506,7 @@ static int at91_gpio_of_irq_setup(struct device_node *node,
 		prev = gpio_chips[at91_gpio->pioc_idx - 1];
 
 	/* The top level handler handles one bank of GPIOs, except
-	 * on some SoC it can handles up to three...
+	 * on some SoC it can handle up to three...
 	 * We only set up the handler for the first of the list.
 	 */
 	if (prev && prev->next == at91_gpio)

drivers/pinctrl/pinctrl-baytrail.c

@@ -286,13 +286,19 @@ static void byt_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
 	spin_lock_irqsave(&vg->lock, flags);
 
 	for (i = 0; i < vg->chip.ngpio; i++) {
+		const char *label;
 		offs = vg->range->pins[i] * 16;
 		conf0 = readl(vg->reg_base + offs + BYT_CONF0_REG);
 		val = readl(vg->reg_base + offs + BYT_VAL_REG);
 
+		label = gpiochip_is_requested(chip, i);
+		if (!label)
+			label = "Unrequested";
+
 		seq_printf(s,
-			   " gpio-%-3d %s %s %s pad-%-3d offset:0x%03x mux:%d %s%s%s\n",
+			   " gpio-%-3d (%-20.20s) %s %s %s pad-%-3d offset:0x%03x mux:%d %s%s%s\n",
 			   i,
+			   label,
 			   val & BYT_INPUT_EN ? "  " : "in",
 			   val & BYT_OUTPUT_EN ? "   " : "out",
 			   val & BYT_LEVEL ? "hi" : "lo",
@@ -366,11 +372,33 @@ static void byt_irq_mask(struct irq_data *d)
 {
 }
 
+static unsigned int byt_irq_startup(struct irq_data *d)
+{
+	struct byt_gpio *vg = irq_data_get_irq_chip_data(d);
+
+	if (gpio_lock_as_irq(&vg->chip, irqd_to_hwirq(d)))
+		dev_err(vg->chip.dev,
+			"unable to lock HW IRQ %lu for IRQ\n",
+			irqd_to_hwirq(d));
+	byt_irq_unmask(d);
+	return 0;
+}
+
+static void byt_irq_shutdown(struct irq_data *d)
+{
+	struct byt_gpio *vg = irq_data_get_irq_chip_data(d);
+
+	byt_irq_mask(d);
+	gpio_unlock_as_irq(&vg->chip, irqd_to_hwirq(d));
+}
+
 static struct irq_chip byt_irqchip = {
 	.name = "BYT-GPIO",
 	.irq_mask = byt_irq_mask,
 	.irq_unmask = byt_irq_unmask,
 	.irq_set_type = byt_irq_type,
+	.irq_startup = byt_irq_startup,
+	.irq_shutdown = byt_irq_shutdown,
 };
 
 static void byt_gpio_irq_init_hw(struct byt_gpio *vg)

drivers/pinctrl/pinctrl-imx1-core.c

@@ -638,6 +638,13 @@ int imx1_pinctrl_core_probe(struct platform_device *pdev,
 		return -EINVAL;
 	}
 
+	ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
+	if (ret) {
+		pinctrl_unregister(ipctl->pctl);
+		dev_err(&pdev->dev, "Failed to populate subdevices\n");
+		return ret;
+	}
+
 	dev_info(&pdev->dev, "initialized IMX pinctrl driver\n");
 
 	return 0;

drivers/pinctrl/pinctrl-imx25.c

+/*
+ * imx25 pinctrl driver.
+ *
+ * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
+ *
+ * This driver was mostly copied from the imx51 pinctrl driver which has:
+ *
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ * Copyright (C) 2012 Linaro, Inc.
+ *
+ * Author: Denis Carikli <denis@eukrea.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-imx.h"
+
+enum imx25_pads {
+	MX25_PAD_RESERVE0 = 1,
+	MX25_PAD_RESERVE1 = 2,
+	MX25_PAD_A10 = 3,
+	MX25_PAD_A13 = 4,
+	MX25_PAD_A14 = 5,
+	MX25_PAD_A15 = 6,
+	MX25_PAD_A16 = 7,
+	MX25_PAD_A17 = 8,
+	MX25_PAD_A18 = 9,
+	MX25_PAD_A19 = 10,
+	MX25_PAD_A20 = 11,
+	MX25_PAD_A21 = 12,
+	MX25_PAD_A22 = 13,
+	MX25_PAD_A23 = 14,
+	MX25_PAD_A24 = 15,
+	MX25_PAD_A25 = 16,
+	MX25_PAD_EB0 = 17,
+	MX25_PAD_EB1 = 18,
+	MX25_PAD_OE = 19,
+	MX25_PAD_CS0 = 20,
+	MX25_PAD_CS1 = 21,
+	MX25_PAD_CS4 = 22,
+	MX25_PAD_CS5 = 23,
+	MX25_PAD_NF_CE0 = 24,
+	MX25_PAD_ECB = 25,
+	MX25_PAD_LBA = 26,
+	MX25_PAD_BCLK = 27,
+	MX25_PAD_RW = 28,
+	MX25_PAD_NFWE_B = 29,
+	MX25_PAD_NFRE_B = 30,
+	MX25_PAD_NFALE = 31,
+	MX25_PAD_NFCLE = 32,
+	MX25_PAD_NFWP_B = 33,
+	MX25_PAD_NFRB = 34,
+	MX25_PAD_D15 = 35,
+	MX25_PAD_D14 = 36,
+	MX25_PAD_D13 = 37,
+	MX25_PAD_D12 = 38,
+	MX25_PAD_D11 = 39,
+	MX25_PAD_D10 = 40,
+	MX25_PAD_D9 = 41,
+	MX25_PAD_D8 = 42,
+	MX25_PAD_D7 = 43,
+	MX25_PAD_D6 = 44,
+	MX25_PAD_D5 = 45,
+	MX25_PAD_D4 = 46,
+	MX25_PAD_D3 = 47,
+	MX25_PAD_D2 = 48,
+	MX25_PAD_D1 = 49,
+	MX25_PAD_D0 = 50,
+	MX25_PAD_LD0 = 51,
+	MX25_PAD_LD1 = 52,
+	MX25_PAD_LD2 = 53,
+	MX25_PAD_LD3 = 54,
+	MX25_PAD_LD4 = 55,
+	MX25_PAD_LD5 = 56,
+	MX25_PAD_LD6 = 57,
+	MX25_PAD_LD7 = 58,
+	MX25_PAD_LD8 = 59,
+	MX25_PAD_LD9 = 60,
+	MX25_PAD_LD10 = 61,
+	MX25_PAD_LD11 = 62,
+	MX25_PAD_LD12 = 63,
+	MX25_PAD_LD13 = 64,
+	MX25_PAD_LD14 = 65,
+	MX25_PAD_LD15 = 66,
+	MX25_PAD_HSYNC = 67,
+	MX25_PAD_VSYNC = 68,
+	MX25_PAD_LSCLK = 69,
+	MX25_PAD_OE_ACD = 70,
+	MX25_PAD_CONTRAST = 71,
+	MX25_PAD_PWM = 72,
+	MX25_PAD_CSI_D2 = 73,
+	MX25_PAD_CSI_D3 = 74,
+	MX25_PAD_CSI_D4 = 75,
+	MX25_PAD_CSI_D5 = 76,
+	MX25_PAD_CSI_D6 = 77,
+	MX25_PAD_CSI_D7 = 78,
+	MX25_PAD_CSI_D8 = 79,
+	MX25_PAD_CSI_D9 = 80,
+	MX25_PAD_CSI_MCLK = 81,
+	MX25_PAD_CSI_VSYNC = 82,
+	MX25_PAD_CSI_HSYNC = 83,
+	MX25_PAD_CSI_PIXCLK = 84,
+	MX25_PAD_I2C1_CLK = 85,
+	MX25_PAD_I2C1_DAT = 86,
+	MX25_PAD_CSPI1_MOSI = 87,
+	MX25_PAD_CSPI1_MISO = 88,
+	MX25_PAD_CSPI1_SS0 = 89,
+	MX25_PAD_CSPI1_SS1 = 90,
+	MX25_PAD_CSPI1_SCLK = 91,
+	MX25_PAD_CSPI1_RDY = 92,
+	MX25_PAD_UART1_RXD = 93,
+	MX25_PAD_UART1_TXD = 94,
+	MX25_PAD_UART1_RTS = 95,
+	MX25_PAD_UART1_CTS = 96,
+	MX25_PAD_UART2_RXD = 97,
+	MX25_PAD_UART2_TXD = 98,
+	MX25_PAD_UART2_RTS = 99,
+	MX25_PAD_UART2_CTS = 100,
+	MX25_PAD_SD1_CMD = 101,
+	MX25_PAD_SD1_CLK = 102,
+	MX25_PAD_SD1_DATA0 = 103,
+	MX25_PAD_SD1_DATA1 = 104,
+	MX25_PAD_SD1_DATA2 = 105,
+	MX25_PAD_SD1_DATA3 = 106,
+	MX25_PAD_KPP_ROW0 = 107,
+	MX25_PAD_KPP_ROW1 = 108,
+	MX25_PAD_KPP_ROW2 = 109,
+	MX25_PAD_KPP_ROW3 = 110,
+	MX25_PAD_KPP_COL0 = 111,
+	MX25_PAD_KPP_COL1 = 112,
+	MX25_PAD_KPP_COL2 = 113,
+	MX25_PAD_KPP_COL3 = 114,
+	MX25_PAD_FEC_MDC = 115,
+	MX25_PAD_FEC_MDIO = 116,
+	MX25_PAD_FEC_TDATA0 = 117,
+	MX25_PAD_FEC_TDATA1 = 118,
+	MX25_PAD_FEC_TX_EN = 119,
+	MX25_PAD_FEC_RDATA0 = 120,
+	MX25_PAD_FEC_RDATA1 = 121,
+	MX25_PAD_FEC_RX_DV = 122,
+	MX25_PAD_FEC_TX_CLK = 123,
+	MX25_PAD_RTCK = 124,
+	MX25_PAD_DE_B = 125,
+	MX25_PAD_GPIO_A = 126,
+	MX25_PAD_GPIO_B = 127,
+	MX25_PAD_GPIO_C = 128,
+	MX25_PAD_GPIO_D = 129,
+	MX25_PAD_GPIO_E = 130,
+	MX25_PAD_GPIO_F = 131,
+	MX25_PAD_EXT_ARMCLK = 132,
+	MX25_PAD_UPLL_BYPCLK = 133,
+	MX25_PAD_VSTBY_REQ = 134,
+	MX25_PAD_VSTBY_ACK = 135,
+	MX25_PAD_POWER_FAIL  = 136,
+	MX25_PAD_CLKO = 137,
+	MX25_PAD_BOOT_MODE0 = 138,
+	MX25_PAD_BOOT_MODE1 = 139,
+};
+
+/* Pad names for the pinmux subsystem */
+static const struct pinctrl_pin_desc imx25_pinctrl_pads[] = {
+	IMX_PINCTRL_PIN(MX25_PAD_RESERVE0),
+	IMX_PINCTRL_PIN(MX25_PAD_RESERVE1),
+	IMX_PINCTRL_PIN(MX25_PAD_A10),
+	IMX_PINCTRL_PIN(MX25_PAD_A13),
+	IMX_PINCTRL_PIN(MX25_PAD_A14),
+	IMX_PINCTRL_PIN(MX25_PAD_A15),
+	IMX_PINCTRL_PIN(MX25_PAD_A16),
+	IMX_PINCTRL_PIN(MX25_PAD_A17),
+	IMX_PINCTRL_PIN(MX25_PAD_A18),
+	IMX_PINCTRL_PIN(MX25_PAD_A19),
+	IMX_PINCTRL_PIN(MX25_PAD_A20),
+	IMX_PINCTRL_PIN(MX25_PAD_A21),
+	IMX_PINCTRL_PIN(MX25_PAD_A22),
+	IMX_PINCTRL_PIN(MX25_PAD_A23),
+	IMX_PINCTRL_PIN(MX25_PAD_A24),
+	IMX_PINCTRL_PIN(MX25_PAD_A25),
+	IMX_PINCTRL_PIN(MX25_PAD_EB0),
+	IMX_PINCTRL_PIN(MX25_PAD_EB1),
+	IMX_PINCTRL_PIN(MX25_PAD_OE),
+	IMX_PINCTRL_PIN(MX25_PAD_CS0),
+	IMX_PINCTRL_PIN(MX25_PAD_CS1),
+	IMX_PINCTRL_PIN(MX25_PAD_CS4),
+	IMX_PINCTRL_PIN(MX25_PAD_CS5),
+	IMX_PINCTRL_PIN(MX25_PAD_NF_CE0),
+	IMX_PINCTRL_PIN(MX25_PAD_ECB),
+	IMX_PINCTRL_PIN(MX25_PAD_LBA),
+	IMX_PINCTRL_PIN(MX25_PAD_BCLK),
+	IMX_PINCTRL_PIN(MX25_PAD_RW),
+	IMX_PINCTRL_PIN(MX25_PAD_NFWE_B),
+	IMX_PINCTRL_PIN(MX25_PAD_NFRE_B),
+	IMX_PINCTRL_PIN(MX25_PAD_NFALE),
+	IMX_PINCTRL_PIN(MX25_PAD_NFCLE),
+	IMX_PINCTRL_PIN(MX25_PAD_NFWP_B),
+	IMX_PINCTRL_PIN(MX25_PAD_NFRB),
+	IMX_PINCTRL_PIN(MX25_PAD_D15),
+	IMX_PINCTRL_PIN(MX25_PAD_D14),
+	IMX_PINCTRL_PIN(MX25_PAD_D13),
+	IMX_PINCTRL_PIN(MX25_PAD_D12),
+	IMX_PINCTRL_PIN(MX25_PAD_D11),
+	IMX_PINCTRL_PIN(MX25_PAD_D10),
+	IMX_PINCTRL_PIN(MX25_PAD_D9),
+	IMX_PINCTRL_PIN(MX25_PAD_D8),
+	IMX_PINCTRL_PIN(MX25_PAD_D7),
+	IMX_PINCTRL_PIN(MX25_PAD_D6),
+	IMX_PINCTRL_PIN(MX25_PAD_D5),
+	IMX_PINCTRL_PIN(MX25_PAD_D4),
+	IMX_PINCTRL_PIN(MX25_PAD_D3),
+	IMX_PINCTRL_PIN(MX25_PAD_D2),
+	IMX_PINCTRL_PIN(MX25_PAD_D1),
+	IMX_PINCTRL_PIN(MX25_PAD_D0),
+	IMX_PINCTRL_PIN(MX25_PAD_LD0),
+	IMX_PINCTRL_PIN(MX25_PAD_LD1),
+	IMX_PINCTRL_PIN(MX25_PAD_LD2),
+	IMX_PINCTRL_PIN(MX25_PAD_LD3),
+	IMX_PINCTRL_PIN(MX25_PAD_LD4),
+	IMX_PINCTRL_PIN(MX25_PAD_LD5),
+	IMX_PINCTRL_PIN(MX25_PAD_LD6),
+	IMX_PINCTRL_PIN(MX25_PAD_LD7),
+	IMX_PINCTRL_PIN(MX25_PAD_LD8),
+	IMX_PINCTRL_PIN(MX25_PAD_LD9),
+	IMX_PINCTRL_PIN(MX25_PAD_LD10),
+	IMX_PINCTRL_PIN(MX25_PAD_LD11),
+	IMX_PINCTRL_PIN(MX25_PAD_LD12),
+	IMX_PINCTRL_PIN(MX25_PAD_LD13),
+	IMX_PINCTRL_PIN(MX25_PAD_LD14),
+	IMX_PINCTRL_PIN(MX25_PAD_LD15),
+	IMX_PINCTRL_PIN(MX25_PAD_HSYNC),
+	IMX_PINCTRL_PIN(MX25_PAD_VSYNC),
+	IMX_PINCTRL_PIN(MX25_PAD_LSCLK),
+	IMX_PINCTRL_PIN(MX25_PAD_OE_ACD),
+	IMX_PINCTRL_PIN(MX25_PAD_CONTRAST),
+	IMX_PINCTRL_PIN(MX25_PAD_PWM),
+	IMX_PINCTRL_PIN(MX25_PAD_CSI_D2),
+	IMX_PINCTRL_PIN(MX25_PAD_CSI_D3),
+	IMX_PINCTRL_PIN(MX25_PAD_CSI_D4),
+	IMX_PINCTRL_PIN(MX25_PAD_CSI_D5),
+	IMX_PINCTRL_PIN(MX25_PAD_CSI_D6),
+	IMX_PINCTRL_PIN(MX25_PAD_CSI_D7),
+	IMX_PINCTRL_PIN(MX25_PAD_CSI_D8),
+	IMX_PINCTRL_PIN(MX25_PAD_CSI_D9),
+	IMX_PINCTRL_PIN(MX25_PAD_CSI_MCLK),
+	IMX_PINCTRL_PIN(MX25_PAD_CSI_VSYNC),
+	IMX_PINCTRL_PIN(MX25_PAD_CSI_HSYNC),
+	IMX_PINCTRL_PIN(MX25_PAD_CSI_PIXCLK),
+	IMX_PINCTRL_PIN(MX25_PAD_I2C1_CLK),
+	IMX_PINCTRL_PIN(MX25_PAD_I2C1_DAT),
+	IMX_PINCTRL_PIN(MX25_PAD_CSPI1_MOSI),
+	IMX_PINCTRL_PIN(MX25_PAD_CSPI1_MISO),
+	IMX_PINCTRL_PIN(MX25_PAD_CSPI1_SS0),
+	IMX_PINCTRL_PIN(MX25_PAD_CSPI1_SS1),
+	IMX_PINCTRL_PIN(MX25_PAD_CSPI1_SCLK),
+	IMX_PINCTRL_PIN(MX25_PAD_CSPI1_RDY),
+	IMX_PINCTRL_PIN(MX25_PAD_UART1_RXD),
+	IMX_PINCTRL_PIN(MX25_PAD_UART1_TXD),
+	IMX_PINCTRL_PIN(MX25_PAD_UART1_RTS),
+	IMX_PINCTRL_PIN(MX25_PAD_UART1_CTS),
+	IMX_PINCTRL_PIN(MX25_PAD_UART2_RXD),
+	IMX_PINCTRL_PIN(MX25_PAD_UART2_TXD),
+	IMX_PINCTRL_PIN(MX25_PAD_UART2_RTS),
+	IMX_PINCTRL_PIN(MX25_PAD_UART2_CTS),
+	IMX_PINCTRL_PIN(MX25_PAD_SD1_CMD),
+	IMX_PINCTRL_PIN(MX25_PAD_SD1_CLK),
+	IMX_PINCTRL_PIN(MX25_PAD_SD1_DATA0),
+	IMX_PINCTRL_PIN(MX25_PAD_SD1_DATA1),
+	IMX_PINCTRL_PIN(MX25_PAD_SD1_DATA2),
+	IMX_PINCTRL_PIN(MX25_PAD_SD1_DATA3),
+	IMX_PINCTRL_PIN(MX25_PAD_KPP_ROW0),
+	IMX_PINCTRL_PIN(MX25_PAD_KPP_ROW1),
+	IMX_PINCTRL_PIN(MX25_PAD_KPP_ROW2),
+	IMX_PINCTRL_PIN(MX25_PAD_KPP_ROW3),
+	IMX_PINCTRL_PIN(MX25_PAD_KPP_COL0),
+	IMX_PINCTRL_PIN(MX25_PAD_KPP_COL1),
+	IMX_PINCTRL_PIN(MX25_PAD_KPP_COL2),
+	IMX_PINCTRL_PIN(MX25_PAD_KPP_COL3),
+	IMX_PINCTRL_PIN(MX25_PAD_FEC_MDC),
+	IMX_PINCTRL_PIN(MX25_PAD_FEC_MDIO),
+	IMX_PINCTRL_PIN(MX25_PAD_FEC_TDATA0),
+	IMX_PINCTRL_PIN(MX25_PAD_FEC_TDATA1),
+	IMX_PINCTRL_PIN(MX25_PAD_FEC_TX_EN),
+	IMX_PINCTRL_PIN(MX25_PAD_FEC_RDATA0),
+	IMX_PINCTRL_PIN(MX25_PAD_FEC_RDATA1),
+	IMX_PINCTRL_PIN(MX25_PAD_FEC_RX_DV),
+	IMX_PINCTRL_PIN(MX25_PAD_FEC_TX_CLK),
+	IMX_PINCTRL_PIN(MX25_PAD_RTCK),
+	IMX_PINCTRL_PIN(MX25_PAD_DE_B),
+	IMX_PINCTRL_PIN(MX25_PAD_GPIO_A),
+	IMX_PINCTRL_PIN(MX25_PAD_GPIO_B),
+	IMX_PINCTRL_PIN(MX25_PAD_GPIO_C),
+	IMX_PINCTRL_PIN(MX25_PAD_GPIO_D),
+	IMX_PINCTRL_PIN(MX25_PAD_GPIO_E),
+	IMX_PINCTRL_PIN(MX25_PAD_GPIO_F),
+	IMX_PINCTRL_PIN(MX25_PAD_EXT_ARMCLK),
+	IMX_PINCTRL_PIN(MX25_PAD_UPLL_BYPCLK),
+	IMX_PINCTRL_PIN(MX25_PAD_VSTBY_REQ),
+	IMX_PINCTRL_PIN(MX25_PAD_VSTBY_ACK),
+	IMX_PINCTRL_PIN(MX25_PAD_POWER_FAIL),
+	IMX_PINCTRL_PIN(MX25_PAD_CLKO),
+	IMX_PINCTRL_PIN(MX25_PAD_BOOT_MODE0),
+	IMX_PINCTRL_PIN(MX25_PAD_BOOT_MODE1),
+};
+
+static struct imx_pinctrl_soc_info imx25_pinctrl_info = {
+	.pins = imx25_pinctrl_pads,
+	.npins = ARRAY_SIZE(imx25_pinctrl_pads),
+};
+
+static struct of_device_id imx25_pinctrl_of_match[] = {
+	{ .compatible = "fsl,imx25-iomuxc", },
+	{ /* sentinel */ }
+};
+
+static int imx25_pinctrl_probe(struct platform_device *pdev)
+{
+	return imx_pinctrl_probe(pdev, &imx25_pinctrl_info);
+}
+
+static struct platform_driver imx25_pinctrl_driver = {
+	.driver = {
+		.name = "imx25-pinctrl",
+		.owner = THIS_MODULE,
+		.of_match_table = of_match_ptr(imx25_pinctrl_of_match),
+	},
+	.probe = imx25_pinctrl_probe,
+	.remove = imx_pinctrl_remove,
+};
+
+static int __init imx25_pinctrl_init(void)
+{
+	return platform_driver_register(&imx25_pinctrl_driver);
+}
+arch_initcall(imx25_pinctrl_init);
+
+static void __exit imx25_pinctrl_exit(void)
+{
+	platform_driver_unregister(&imx25_pinctrl_driver);
+}
+module_exit(imx25_pinctrl_exit);
+MODULE_AUTHOR("Denis Carikli <denis@eukrea.com>");
+MODULE_DESCRIPTION("Freescale IMX25 pinctrl driver");
+MODULE_LICENSE("GPL v2");

drivers/pinctrl/pinctrl-msm.h

+/*
+ * Copyright (c) 2013, Sony Mobile Communications AB.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+#ifndef __PINCTRL_MSM_H__
+#define __PINCTRL_MSM_H__
+
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/machine.h>
+
+/**
+ * struct msm_function - a pinmux function
+ * @name:    Name of the pinmux function.
+ * @groups:  List of pingroups for this function.
+ * @ngroups: Number of entries in @groups.
+ */
+struct msm_function {
+	const char *name;
+	const char * const *groups;
+	unsigned ngroups;
+};
+
+/**
+ * struct msm_pingroup - Qualcomm pingroup definition
+ * @name:                 Name of the pingroup.
+ * @pins:	          A list of pins assigned to this pingroup.
+ * @npins:	          Number of entries in @pins.
+ * @funcs:                A list of pinmux functions that can be selected for
+ *                        this group. The index of the selected function is used
+ *                        for programming the function selector.
+ *                        Entries should be indices into the groups list of the
+ *                        struct msm_pinctrl_soc_data.
+ * @ctl_reg:              Offset of the register holding control bits for this group.
+ * @io_reg:               Offset of the register holding input/output bits for this group.
+ * @intr_cfg_reg:         Offset of the register holding interrupt configuration bits.
+ * @intr_status_reg:      Offset of the register holding the status bits for this group.
+ * @intr_target_reg:      Offset of the register specifying routing of the interrupts
+ *                        from this group.
+ * @mux_bit:              Offset in @ctl_reg for the pinmux function selection.
+ * @pull_bit:             Offset in @ctl_reg for the bias configuration.
+ * @drv_bit:              Offset in @ctl_reg for the drive strength configuration.
+ * @oe_bit:               Offset in @ctl_reg for controlling output enable.
+ * @in_bit:               Offset in @io_reg for the input bit value.
+ * @out_bit:              Offset in @io_reg for the output bit value.
+ * @intr_enable_bit:      Offset in @intr_cfg_reg for enabling the interrupt for this group.
+ * @intr_status_bit:      Offset in @intr_status_reg for reading and acking the interrupt
+ *                        status.
+ * @intr_target_bit:      Offset in @intr_target_reg for configuring the interrupt routing.
+ * @intr_raw_status_bit:  Offset in @intr_cfg_reg for the raw status bit.
+ * @intr_polarity_bit:    Offset in @intr_cfg_reg for specifying polarity of the interrupt.
+ * @intr_detection_bit:   Offset in @intr_cfg_reg for specifying interrupt type.
+ * @intr_detection_width: Number of bits used for specifying interrupt type,
+ *                        Should be 2 for SoCs that can detect both edges in hardware,
+ *                        otherwise 1.
+ */
+struct msm_pingroup {
+	const char *name;
+	const unsigned *pins;
+	unsigned npins;
+
+	unsigned funcs[8];
+
+	s16 ctl_reg;
+	s16 io_reg;
+	s16 intr_cfg_reg;
+	s16 intr_status_reg;
+	s16 intr_target_reg;
+
+	unsigned mux_bit:5;
+
+	unsigned pull_bit:5;
+	unsigned drv_bit:5;
+
+	unsigned oe_bit:5;
+	unsigned in_bit:5;
+	unsigned out_bit:5;
+
+	unsigned intr_enable_bit:5;
+	unsigned intr_status_bit:5;
+
+	unsigned intr_target_bit:5;
+	unsigned intr_raw_status_bit:5;
+	unsigned intr_polarity_bit:5;
+	unsigned intr_detection_bit:5;
+	unsigned intr_detection_width:5;
+};
+
+/**
+ * struct msm_pinctrl_soc_data - Qualcomm pin controller driver configuration
+ * @pins:       An array describing all pins the pin controller affects.
+ * @npins:      The number of entries in @pins.
+ * @functions:  An array describing all mux functions the SoC supports.
+ * @nfunctions: The number of entries in @functions.
+ * @groups:     An array describing all pin groups the pin SoC supports.
+ * @ngroups:    The numbmer of entries in @groups.
+ * @ngpio:      The number of pingroups the driver should expose as GPIOs.
+ */
+struct msm_pinctrl_soc_data {
+	const struct pinctrl_pin_desc *pins;
+	unsigned npins;
+	const struct msm_function *functions;
+	unsigned nfunctions;
+	const struct msm_pingroup *groups;
+	unsigned ngroups;
+	unsigned ngpios;
+};
+
+int msm_pinctrl_probe(struct platform_device *pdev,
+		      const struct msm_pinctrl_soc_data *soc_data);
+int msm_pinctrl_remove(struct platform_device *pdev);
+
+#endif

drivers/pinctrl/pinctrl-nomadik.c

@@ -846,14 +846,14 @@ static void nmk_gpio_dbg_show_one(struct seq_file *s,
 		   (mode < 0) ? "unknown" : modes[mode],
 		   pull ? "pull" : "none");
 
-	if (label && !is_out) {
-		int		irq = gpio_to_irq(gpio);
+	if (!is_out) {
+		int irq = gpio_to_irq(gpio);
 		struct irq_desc	*desc = irq_to_desc(irq);
 
 		/* This races with request_irq(), set_irq_type(),
 		 * and set_irq_wake() ... but those are "rare".
 		 */
-		if (irq >= 0 && desc->action) {
+		if (irq > 0 && desc && desc->action) {
 			char *trigger;
 			u32 bitmask = nmk_gpio_get_bitmask(gpio);
 

drivers/pinctrl/sh-pfc/core.c

@@ -26,29 +26,67 @@
 
 #include "core.h"
 
-static int sh_pfc_ioremap(struct sh_pfc *pfc, struct platform_device *pdev)
+static int sh_pfc_map_resources(struct sh_pfc *pfc,
+				struct platform_device *pdev)
 {
+	unsigned int num_windows = 0;
+	unsigned int num_irqs = 0;
+	struct sh_pfc_window *windows;
+	unsigned int *irqs = NULL;
 	struct resource *res;
-	int k;
+	unsigned int i;
+
+	/* Count the MEM and IRQ resources. */
+	for (i = 0; i < pdev->num_resources; ++i) {
+		switch (resource_type(&pdev->resource[i])) {
+		case IORESOURCE_MEM:
+			num_windows++;
+			break;
+
+		case IORESOURCE_IRQ:
+			num_irqs++;
+			break;
+		}
+	}
 
-	if (pdev->num_resources == 0)
+	if (num_windows == 0)
 		return -EINVAL;
 
-	pfc->window = devm_kzalloc(pfc->dev, pdev->num_resources *
-				   sizeof(*pfc->window), GFP_NOWAIT);
-	if (!pfc->window)
+	/* Allocate memory windows and IRQs arrays. */
+	windows = devm_kzalloc(pfc->dev, num_windows * sizeof(*windows),
+			       GFP_KERNEL);
+	if (windows == NULL)
 		return -ENOMEM;
 
-	pfc->num_windows = pdev->num_resources;
+	pfc->num_windows = num_windows;
+	pfc->windows = windows;
 
-	for (k = 0, res = pdev->resource; k < pdev->num_resources; k++, res++) {
-		WARN_ON(resource_type(res) != IORESOURCE_MEM);
-		pfc->window[k].phys = res->start;
-		pfc->window[k].size = resource_size(res);
-		pfc->window[k].virt = devm_ioremap_nocache(pfc->dev, res->start,
-							   resource_size(res));
-		if (!pfc->window[k].virt)
+	if (num_irqs) {
+		irqs = devm_kzalloc(pfc->dev, num_irqs * sizeof(*irqs),
+				    GFP_KERNEL);
+		if (irqs == NULL)
 			return -ENOMEM;
+
+		pfc->num_irqs = num_irqs;
+		pfc->irqs = irqs;
+	}
+
+	/* Fill them. */
+	for (i = 0, res = pdev->resource; i < pdev->num_resources; i++, res++) {
+		switch (resource_type(res)) {
+		case IORESOURCE_MEM:
+			windows->phys = res->start;
+			windows->size = resource_size(res);
+			windows->virt = devm_ioremap_resource(pfc->dev, res);
+			if (IS_ERR(windows->virt))
+				return -ENOMEM;
+			windows++;
+			break;
+
+		case IORESOURCE_IRQ:
+			*irqs++ = res->start;
+			break;
+		}
 	}
 
 	return 0;
@@ -62,7 +100,7 @@ static void __iomem *sh_pfc_phys_to_virt(struct sh_pfc *pfc,
 
 	/* scan through physical windows and convert address */
 	for (i = 0; i < pfc->num_windows; i++) {
-		window = pfc->window + i;
+		window = pfc->windows + i;
 
 		if (address < window->phys)
 			continue;
@@ -147,7 +185,7 @@ static void sh_pfc_config_reg_helper(struct sh_pfc *pfc,
 				     unsigned long *maskp,
 				     unsigned long *posp)
 {
-	int k;
+	unsigned int k;
 
 	*mapped_regp = sh_pfc_phys_to_virt(pfc, crp->reg);
 
@@ -196,7 +234,7 @@ static int sh_pfc_get_config_reg(struct sh_pfc *pfc, u16 enum_id,
 {
 	const struct pinmux_cfg_reg *config_reg;
 	unsigned long r_width, f_width, curr_width, ncomb;
-	int k, m, n, pos, bit_pos;
+	unsigned int k, m, n, pos, bit_pos;
 
 	k = 0;
 	while (1) {
@@ -238,7 +276,7 @@ static int sh_pfc_mark_to_enum(struct sh_pfc *pfc, u16 mark, int pos,
 			      u16 *enum_idp)
 {
 	const u16 *data = pfc->info->gpio_data;
-	int k;
+	unsigned int k;
 
 	if (pos) {
 		*enum_idp = data[pos + 1];
@@ -481,7 +519,7 @@ static int sh_pfc_probe(struct platform_device *pdev)
 	pfc->info = info;
 	pfc->dev = &pdev->dev;
 
-	ret = sh_pfc_ioremap(pfc, pdev);
+	ret = sh_pfc_map_resources(pfc, pdev);
 	if (unlikely(ret < 0))
 		return ret;
 

drivers/pinctrl/sh-pfc/core.h

@@ -37,7 +37,9 @@ struct sh_pfc {
 	spinlock_t lock;
 
 	unsigned int num_windows;
-	struct sh_pfc_window *window;
+	struct sh_pfc_window *windows;
+	unsigned int num_irqs;
+	unsigned int *irqs;
 
 	struct sh_pfc_pin_range *ranges;
 	unsigned int nr_ranges;

drivers/pinctrl/sh-pfc/gpio.c

@@ -204,18 +204,24 @@ static void gpio_pin_set(struct gpio_chip *gc, unsigned offset, int value)
 static int gpio_pin_to_irq(struct gpio_chip *gc, unsigned offset)
 {
 	struct sh_pfc *pfc = gpio_to_pfc(gc);
-	int i, k;
+	unsigned int i, k;
 
 	for (i = 0; i < pfc->info->gpio_irq_size; i++) {
-		unsigned short *gpios = pfc->info->gpio_irq[i].gpios;
+		short *gpios = pfc->info->gpio_irq[i].gpios;
 
-		for (k = 0; gpios[k]; k++) {
+		for (k = 0; gpios[k] >= 0; k++) {
 			if (gpios[k] == offset)
-				return pfc->info->gpio_irq[i].irq;
+				goto found;
 		}
 	}
 
 	return -ENOSYS;
+
+found:
+	if (pfc->num_irqs)
+		return pfc->irqs[i];
+	else
+		return pfc->info->gpio_irq[i].irq;
 }
 
 static int gpio_pin_setup(struct sh_pfc_chip *chip)
@@ -347,7 +353,7 @@ int sh_pfc_register_gpiochip(struct sh_pfc *pfc)
 	 * GPIOs.
 	 */
 	for (i = 0; i < pfc->num_windows; ++i) {
-		struct sh_pfc_window *window = &pfc->window[i];
+		struct sh_pfc_window *window = &pfc->windows[i];
 
 		if (pfc->info->data_regs[0].reg >= window->phys &&
 		    pfc->info->data_regs[0].reg < window->phys + window->size)
@@ -357,8 +363,14 @@ int sh_pfc_register_gpiochip(struct sh_pfc *pfc)
 	if (i == pfc->num_windows)
 		return 0;
 
+	/* If we have IRQ resources make sure their number is correct. */
+	if (pfc->num_irqs && pfc->num_irqs != pfc->info->gpio_irq_size) {
+		dev_err(pfc->dev, "invalid number of IRQ resources\n");
+		return -EINVAL;
+	}
+
 	/* Register the real GPIOs chip. */
-	chip = sh_pfc_add_gpiochip(pfc, gpio_pin_setup, &pfc->window[i]);
+	chip = sh_pfc_add_gpiochip(pfc, gpio_pin_setup, &pfc->windows[i]);
 	if (IS_ERR(chip))
 		return PTR_ERR(chip);
 

drivers/pinctrl/sh-pfc/pfc-r8a73a4.c

@@ -2061,17 +2061,6 @@ static const struct sh_pfc_function pinmux_functions[] = {
 	SH_PFC_FUNCTION(sdhi2),
 };
 
-#undef PORTCR
-#define PORTCR(nr, reg)							\
-	{								\
-		PINMUX_CFG_REG("PORT" nr "CR", reg, 8, 4) {		\
-			_PCRH(PORT##nr##_IN, 0, 0, PORT##nr##_OUT),	\
-				PORT##nr##_FN0, PORT##nr##_FN1,		\
-				PORT##nr##_FN2, PORT##nr##_FN3,		\
-				PORT##nr##_FN4, PORT##nr##_FN5,		\
-				PORT##nr##_FN6, PORT##nr##_FN7 }	\
-	}
-
 static const struct pinmux_cfg_reg pinmux_config_regs[] = {
 	PORTCR(0, 0xe6050000),
 	PORTCR(1, 0xe6050001),
@@ -2691,7 +2680,7 @@ static unsigned int r8a73a4_pinmux_get_bias(struct sh_pfc *pfc,
 {
 	void __iomem *addr;
 
-	addr = pfc->window->virt + r8a73a4_portcr_offsets[pin >> 5] + pin;
+	addr = pfc->windows->virt + r8a73a4_portcr_offsets[pin >> 5] + pin;
 
 	switch (ioread8(addr) & PORTCR_PULMD_MASK) {
 	case PORTCR_PULMD_UP:
@@ -2710,7 +2699,7 @@ static void r8a73a4_pinmux_set_bias(struct sh_pfc *pfc, unsigned int pin,
 	void __iomem *addr;
 	u32 value;
 
-	addr = pfc->window->virt + r8a73a4_portcr_offsets[pin >> 5] + pin;
+	addr = pfc->windows->virt + r8a73a4_portcr_offsets[pin >> 5] + pin;
 	value = ioread8(addr) & ~PORTCR_PULMD_MASK;
 
 	switch (bias) {

drivers/pinctrl/sh-pfc/pfc-r8a7740.c

@@ -3234,17 +3234,6 @@ static const struct sh_pfc_function pinmux_functions[] = {
 	SH_PFC_FUNCTION(tpu0),
 };
 
-#undef PORTCR
-#define PORTCR(nr, reg)							\
-	{								\
-		PINMUX_CFG_REG("PORT" nr "CR", reg, 8, 4) {		\
-			_PCRH(PORT##nr##_IN, 0, 0, PORT##nr##_OUT),	\
-				PORT##nr##_FN0, PORT##nr##_FN1,		\
-				PORT##nr##_FN2, PORT##nr##_FN3,		\
-				PORT##nr##_FN4, PORT##nr##_FN5,		\
-				PORT##nr##_FN6, PORT##nr##_FN7 }	\
-	}
-
 static const struct pinmux_cfg_reg pinmux_config_regs[] = {
 	PORTCR(0,	0xe6050000), /* PORT0CR */
 	PORTCR(1,	0xe6050001), /* PORT1CR */
@@ -3721,7 +3710,7 @@ static void __iomem *r8a7740_pinmux_portcr(struct sh_pfc *pfc, unsigned int pin)
 			&r8a7740_portcr_offsets[i];
 
 		if (i <= group->end_pin)
-			return pfc->window->virt + group->offset + pin;
+			return pfc->windows->virt + group->offset + pin;
 	}
 
 	return NULL;

drivers/pinctrl/sh-pfc/pfc-r8a7791.c

@@ -1730,11 +1730,11 @@ static const unsigned int du_clk_out_1_pins[] = {
 static const unsigned int du_clk_out_1_mux[] = {
 	DU1_DOTCLKOUT1_MARK
 };
-static const unsigned int du_sync_1_pins[] = {
+static const unsigned int du_sync_pins[] = {
 	/* EXVSYNC/VSYNC, EXHSYNC/HSYNC, EXDISP/EXODDF/EXCDE */
 	RCAR_GP_PIN(3, 29), RCAR_GP_PIN(3, 28), RCAR_GP_PIN(3, 27),
 };
-static const unsigned int du_sync_1_mux[] = {
+static const unsigned int du_sync_mux[] = {
 	DU1_EXODDF_DU1_ODDF_DISP_CDE_MARK,
 	DU1_EXVSYNC_DU1_VSYNC_MARK, DU1_EXHSYNC_DU1_HSYNC_MARK
 };
@@ -1742,6 +1742,9 @@ static const unsigned int du_cde_disp_pins[] = {
 	/* CDE DISP */
 	RCAR_GP_PIN(3, 31), RCAR_GP_PIN(3, 30),
 };
+static const unsigned int du_cde_disp_mux[] = {
+	DU1_CDE_MARK, DU1_DISP_MARK
+};
 static const unsigned int du0_clk_in_pins[] = {
 	/* CLKIN */
 	RCAR_GP_PIN(6, 31),
@@ -1749,15 +1752,26 @@ static const unsigned int du0_clk_in_pins[] = {
 static const unsigned int du0_clk_in_mux[] = {
 	DU0_DOTCLKIN_MARK
 };
-static const unsigned int du_cde_disp_mux[] = {
-	DU1_CDE_MARK, DU1_DISP_MARK
-};
 static const unsigned int du1_clk_in_pins[] = {
 	/* CLKIN */
-	RCAR_GP_PIN(7, 20), RCAR_GP_PIN(7, 19), RCAR_GP_PIN(3, 24),
+	RCAR_GP_PIN(3, 24),
 };
 static const unsigned int du1_clk_in_mux[] = {
-	DU1_DOTCLKIN_C_MARK, DU1_DOTCLKIN_B_MARK, DU1_DOTCLKIN_MARK
+	DU1_DOTCLKIN_MARK
+};
+static const unsigned int du1_clk_in_b_pins[] = {
+	/* CLKIN */
+	RCAR_GP_PIN(7, 19),
+};
+static const unsigned int du1_clk_in_b_mux[] = {
+	DU1_DOTCLKIN_B_MARK,
+};
+static const unsigned int du1_clk_in_c_pins[] = {
+	/* CLKIN */
+	RCAR_GP_PIN(7, 20),
+};
+static const unsigned int du1_clk_in_c_mux[] = {
+	DU1_DOTCLKIN_C_MARK,
 };
 /* - ETH -------------------------------------------------------------------- */
 static const unsigned int eth_link_pins[] = {
@@ -2670,10 +2684,12 @@ static const struct sh_pfc_pin_group pinmux_groups[] = {
 	SH_PFC_PIN_GROUP(du_rgb888),
 	SH_PFC_PIN_GROUP(du_clk_out_0),
 	SH_PFC_PIN_GROUP(du_clk_out_1),
-	SH_PFC_PIN_GROUP(du_sync_1),
+	SH_PFC_PIN_GROUP(du_sync),
 	SH_PFC_PIN_GROUP(du_cde_disp),
 	SH_PFC_PIN_GROUP(du0_clk_in),
 	SH_PFC_PIN_GROUP(du1_clk_in),
+	SH_PFC_PIN_GROUP(du1_clk_in_b),
+	SH_PFC_PIN_GROUP(du1_clk_in_c),
 	SH_PFC_PIN_GROUP(eth_link),
 	SH_PFC_PIN_GROUP(eth_magic),
 	SH_PFC_PIN_GROUP(eth_mdio),
@@ -2805,7 +2821,7 @@ static const char * const du_groups[] = {
 	"du_rgb888",
 	"du_clk_out_0",
 	"du_clk_out_1",
-	"du_sync_1",
+	"du_sync",
 	"du_cde_disp",
 };
 
@@ -2815,6 +2831,8 @@ static const char * const du0_groups[] = {
 
 static const char * const du1_groups[] = {
 	"du1_clk_in",
+	"du1_clk_in_b",
+	"du1_clk_in_c",
 };
 
 static const char * const eth_groups[] = {
@@ -2840,20 +2858,29 @@ static const char * const mmc_groups[] = {
 
 static const char * const msiof0_groups[] = {
 	"msiof0_clk",
-	"msiof0_ctrl",
-	"msiof0_data",
+	"msiof0_sync",
+	"msiof0_ss1",
+	"msiof0_ss2",
+	"msiof0_rx",
+	"msiof0_tx",
 };
 
 static const char * const msiof1_groups[] = {
 	"msiof1_clk",
-	"msiof1_ctrl",
-	"msiof1_data",
+	"msiof1_sync",
+	"msiof1_ss1",
+	"msiof1_ss2",
+	"msiof1_rx",
+	"msiof1_tx",
 };
 
 static const char * const msiof2_groups[] = {
 	"msiof2_clk",
-	"msiof2_ctrl",
-	"msiof2_data",
+	"msiof2_sync",
+	"msiof2_ss1",
+	"msiof2_ss2",
+	"msiof2_rx",
+	"msiof2_tx",
 };
 
 static const char * const scif0_groups[] = {

drivers/pinctrl/sh-pfc/pfc-sh7372.c

@@ -2118,17 +2118,6 @@ static const struct sh_pfc_function pinmux_functions[] = {
 	SH_PFC_FUNCTION(usb1),
 };
 
-#undef PORTCR
-#define PORTCR(nr, reg)							\
-	{								\
-		PINMUX_CFG_REG("PORT" nr "CR", reg, 8, 4) {		\
-			_PCRH(PORT##nr##_IN, 0, 0, PORT##nr##_OUT),     \
-				PORT##nr##_FN0, PORT##nr##_FN1,		\
-				PORT##nr##_FN2, PORT##nr##_FN3,		\
-				PORT##nr##_FN4, PORT##nr##_FN5,		\
-				PORT##nr##_FN6, PORT##nr##_FN7 }	\
-	}
-
 static const struct pinmux_cfg_reg pinmux_config_regs[] = {
 	PORTCR(0,	0xE6051000), /* PORT0CR */
 	PORTCR(1,	0xE6051001), /* PORT1CR */
@@ -2585,7 +2574,7 @@ static void __iomem *sh7372_pinmux_portcr(struct sh_pfc *pfc, unsigned int pin)
 			&sh7372_portcr_offsets[i];
 
 		if (i <= group->end_pin)
-			return pfc->window->virt + group->offset + pin;
+			return pfc->windows->virt + group->offset + pin;
 	}
 
 	return NULL;

drivers/pinctrl/sh-pfc/pfc-sh73a0.c

@@ -3138,16 +3138,6 @@ static const struct sh_pfc_function pinmux_functions[] = {
 	SH_PFC_FUNCTION(usb),
 };
 
-#undef PORTCR
-#define PORTCR(nr, reg)							\
-	{								\
-		PINMUX_CFG_REG("PORT" nr "CR", reg, 8, 4) {		\
-			_PCRH(PORT##nr##_IN, 0, 0, PORT##nr##_OUT),	\
-				PORT##nr##_FN0, PORT##nr##_FN1,		\
-				PORT##nr##_FN2, PORT##nr##_FN3,		\
-				PORT##nr##_FN4, PORT##nr##_FN5,		\
-				PORT##nr##_FN6, PORT##nr##_FN7 }	\
-	}
 static const struct pinmux_cfg_reg pinmux_config_regs[] = {
 	PORTCR(0, 0xe6050000), /* PORT0CR */
 	PORTCR(1, 0xe6050001), /* PORT1CR */
@@ -3661,38 +3651,38 @@ static const struct pinmux_data_reg pinmux_data_regs[] = {
 };
 
 static const struct pinmux_irq pinmux_irqs[] = {
-	PINMUX_IRQ(irq_pin(19), 9),
-	PINMUX_IRQ(irq_pin(1), 10),
 	PINMUX_IRQ(irq_pin(0), 11),
+	PINMUX_IRQ(irq_pin(1), 10),
+	PINMUX_IRQ(irq_pin(2), 149),
+	PINMUX_IRQ(irq_pin(3), 224),
+	PINMUX_IRQ(irq_pin(4), 159),
+	PINMUX_IRQ(irq_pin(5), 227),
+	PINMUX_IRQ(irq_pin(6), 147),
+	PINMUX_IRQ(irq_pin(7), 150),
+	PINMUX_IRQ(irq_pin(8), 223),
+	PINMUX_IRQ(irq_pin(9), 56, 308),
+	PINMUX_IRQ(irq_pin(10), 54),
+	PINMUX_IRQ(irq_pin(11), 238),
+	PINMUX_IRQ(irq_pin(12), 156),
+	PINMUX_IRQ(irq_pin(13), 239),
+	PINMUX_IRQ(irq_pin(14), 251),
+	PINMUX_IRQ(irq_pin(15), 0),
+	PINMUX_IRQ(irq_pin(16), 249),
+	PINMUX_IRQ(irq_pin(17), 234),
 	PINMUX_IRQ(irq_pin(18), 13),
+	PINMUX_IRQ(irq_pin(19), 9),
 	PINMUX_IRQ(irq_pin(20), 14),
 	PINMUX_IRQ(irq_pin(21), 15),
-	PINMUX_IRQ(irq_pin(31), 26),
-	PINMUX_IRQ(irq_pin(30), 27),
-	PINMUX_IRQ(irq_pin(29), 28),
 	PINMUX_IRQ(irq_pin(22), 40),
 	PINMUX_IRQ(irq_pin(23), 53),
-	PINMUX_IRQ(irq_pin(10), 54),
-	PINMUX_IRQ(irq_pin(9), 56),
+	PINMUX_IRQ(irq_pin(24), 118),
+	PINMUX_IRQ(irq_pin(25), 164),
 	PINMUX_IRQ(irq_pin(26), 115),
 	PINMUX_IRQ(irq_pin(27), 116),
 	PINMUX_IRQ(irq_pin(28), 117),
-	PINMUX_IRQ(irq_pin(24), 118),
-	PINMUX_IRQ(irq_pin(6), 147),
-	PINMUX_IRQ(irq_pin(2), 149),
-	PINMUX_IRQ(irq_pin(7), 150),
-	PINMUX_IRQ(irq_pin(12), 156),
-	PINMUX_IRQ(irq_pin(4), 159),
-	PINMUX_IRQ(irq_pin(25), 164),
-	PINMUX_IRQ(irq_pin(8), 223),
-	PINMUX_IRQ(irq_pin(3), 224),
-	PINMUX_IRQ(irq_pin(5), 227),
-	PINMUX_IRQ(irq_pin(17), 234),
-	PINMUX_IRQ(irq_pin(11), 238),
-	PINMUX_IRQ(irq_pin(13), 239),
-	PINMUX_IRQ(irq_pin(16), 249),
-	PINMUX_IRQ(irq_pin(14), 251),
-	PINMUX_IRQ(irq_pin(9), 308),
+	PINMUX_IRQ(irq_pin(29), 28),
+	PINMUX_IRQ(irq_pin(30), 27),
+	PINMUX_IRQ(irq_pin(31), 26),
 };
 
 /* -----------------------------------------------------------------------------
@@ -3702,7 +3692,7 @@ static const struct pinmux_irq pinmux_irqs[] = {
 static void sh73a0_vccq_mc0_endisable(struct regulator_dev *reg, bool enable)
 {
 	struct sh_pfc *pfc = reg->reg_data;
-	void __iomem *addr = pfc->window[1].virt + 4;
+	void __iomem *addr = pfc->windows[1].virt + 4;
 	unsigned long flags;
 	u32 value;
 
@@ -3735,7 +3725,7 @@ static int sh73a0_vccq_mc0_disable(struct regulator_dev *reg)
 static int sh73a0_vccq_mc0_is_enabled(struct regulator_dev *reg)
 {
 	struct sh_pfc *pfc = reg->reg_data;
-	void __iomem *addr = pfc->window[1].virt + 4;
+	void __iomem *addr = pfc->windows[1].virt + 4;
 	unsigned long flags;
 	u32 value;
 
@@ -3794,7 +3784,7 @@ static const unsigned int sh73a0_portcr_offsets[] = {
 
 static unsigned int sh73a0_pinmux_get_bias(struct sh_pfc *pfc, unsigned int pin)
 {
-	void __iomem *addr = pfc->window->virt
+	void __iomem *addr = pfc->windows->virt
 			   + sh73a0_portcr_offsets[pin >> 5] + pin;
 	u32 value = ioread8(addr) & PORTnCR_PULMD_MASK;
 
@@ -3812,7 +3802,7 @@ static unsigned int sh73a0_pinmux_get_bias(struct sh_pfc *pfc, unsigned int pin)
 static void sh73a0_pinmux_set_bias(struct sh_pfc *pfc, unsigned int pin,
 				   unsigned int bias)
 {
-	void __iomem *addr = pfc->window->virt
+	void __iomem *addr = pfc->windows->virt
 			   + sh73a0_portcr_offsets[pin >> 5] + pin;
 	u32 value = ioread8(addr) & ~PORTnCR_PULMD_MASK;
 

drivers/pinctrl/sh-pfc/sh_pfc.h

@@ -94,11 +94,11 @@ struct pinmux_data_reg {
 
 struct pinmux_irq {
 	int irq;
-	unsigned short *gpios;
+	short *gpios;
 };
 
 #define PINMUX_IRQ(irq_nr, ids...)			   \
-	{ .irq = irq_nr, .gpios = (unsigned short []) { ids, 0 } }	\
+	{ .irq = irq_nr, .gpios = (short []) { ids, -1 } }
 
 struct pinmux_range {
 	u16 begin;
@@ -304,8 +304,7 @@ struct sh_pfc_soc_info {
 #define PORTCR(nr, reg)							\
 	{								\
 		PINMUX_CFG_REG("PORT" nr "CR", reg, 8, 4) {		\
-			_PCRH(PORT##nr##_IN, PORT##nr##_IN_PD,		\
-			      PORT##nr##_IN_PU, PORT##nr##_OUT),	\
+			_PCRH(PORT##nr##_IN, 0, 0, PORT##nr##_OUT),	\
 				PORT##nr##_FN0, PORT##nr##_FN1,		\
 				PORT##nr##_FN2, PORT##nr##_FN3,		\
 				PORT##nr##_FN4, PORT##nr##_FN5,		\

include/linux/pinctrl/pinconf-generic.h

@@ -82,8 +82,10 @@
  *	operation, if several modes of operation are supported these can be
  *	passed in the argument on a custom form, else just use argument 1
  *	to indicate low power mode, argument 0 turns low power mode off.
- * @PIN_CONFIG_OUTPUT: this will configure the pin in output, use argument
- *	1 to indicate high level, argument 0 to indicate low level.
+ * @PIN_CONFIG_OUTPUT: this will configure the pin as an output. Use argument
+ *	1 to indicate high level, argument 0 to indicate low level. (Please
+ *	see Documentation/pinctrl.txt, section "GPIO mode pitfalls" for a
+ *	discussion around this parameter.)
  * @PIN_CONFIG_END: this is the last enumerator for pin configurations, if
  *	you need to pass in custom configurations to the pin controller, use
  *	PIN_CONFIG_END+1 as the base offset.