Early versions of the SFX7101 firmware could complete link training in
a state where it would not adequately cancel noise (Solarflare bug
10750).  We previously worked around this by resetting the PHY after
seeing many Ethernet CRC errors.  This workaround is unsafe since it
takes no account of the interval between errors; it also appears to
be unnecessary with production firmware.  Therefore remove it.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pci_disable_device() disables many features, like MSI-X, which we
never reenable in efx_reset().  Further, calls to pci_enable_device()
and pci_disable_device() must be matched since the nesting count was
introduced, so switch to using pci_clear_master() instead.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Currently the mtd field is not initialised early enough.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of the PHY type names are overly generic.  Change them to include
the model numbers of the PHYs they represent.

Correct the model number reference at the top of xfp_phy.c.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support code for the SFN4111T 100/1000/10GBASE-T reference design,
based in part on the existing code for the SFE4001.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add type codes for the new PHY and rename the SFX7101 type code.

Add definition of clause 22 extension MMD.

Adapt the 10Xpress SFX7101 code to support the SFT9001 as well.
Clean up register definitions.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Steve Hodgson <shodgson@solarflare.com>

MAC, PHY and board events may be separately enabled and signalled.
Our current arrangement of chaining the polling functions can result
in events being missed.  Change them to be more independent.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add infrastructure for auto-negotiation of speed, duplex and flow
control.

When using 10Xpress, auto-negotiate flow control.  While we're
at it, clean up the code to warn when partner is not 10GBASE-T
capable.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SFC4000 has a separate MAC for use at sub-10G speeds.  Introduce
an efx_mac_operations structure with implementations for the two MACs.
Switch between the MACs as necessary.

PHY settings are independent of the MAC, so add get_settings() and
set_settings() to efx_phy_operations.  Also add macs field to indicate
which MACs the PHY is connected to.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace efx_nic::link_options bitfield with link_speed (speed in
Mbit/s) and link_fd (full duplex flag).

Remove broken auto-negotiation functions.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The loopback self-test checks that IP packets with incorrect checksums
are not altered when sent on a queue with checksum generation off.
These should not contribute to RX error statistics.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate IRQs with the name format <device>[-<type>]-<number> so that
future versions of irqbalanced understand what we're doing.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SFC4000 has strap pins indicating the presence of SPI flash and/or
EEPROM.  These pins are also used for GPIO, and in some cases they may
be read wrongly at reset.  However, on production boards it must boot
from one or the other device, so we can assume the boot device is
present and read the board config from there.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make falcon_spi_wait() ignore the write timer - it is only relevant to
write commands, it only works for the device that contains VPD, and it
might not be initialised properly at all.

Rename falcon_spi_fast_wait() to falcon_spi_wait_write(), reflecting
its use, and make it wait up to 10 ms (not 1 ms) since buffered writes
to EEPROM may take this long to complete.

Make both wait functions sleep instead of busy-waiting.

Replace wait for command completion at top of falcon_spi_cmd() with a
single poll; no command should be running when the function starts.

Correct some comments.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was only ever needed for an FPGA version of Falcon.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on a patch by Andrew Morton.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The boot code that appears as a PCI expansion ROM on the SFC4000 is
stored in flash.  Expose this as a standard MTD device to allow for
in-place upgrades.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Move flash and EEPROM partition boundary constants into spi.h and rename
them to be consistent.

Add a comment on the partitioning.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

FALCON_SPI_MAX_LEN has type size_t while other SPI lengths have type
unsigned int.  This results in warnings from min() on 64-bit
architectures where they are different.  Add a cast to make it match.

From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This should avoid an interrupt storm, which has been observed in the
field with one faulty board.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This prevents speculative reading of the statistics before the
completion flag.

From: Neil Turton <nturton@solarflare.com>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Increase the potential retry count for RX flushes from 5 to 100.

Stop polling the RX_DESC_PTR_TBL to infer that a flush might have
happened. Instead absolutely rely on the flush events, unless bug 7803
applies (Falcon rev A only).

To keep things quick, request flushes for every TX and RX queue up
front, and match up the events to requests.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Include PMA/PMD in loopback self-tests as intended.

Add NVRAM checksum validation and include it in self-tests.

Add register self-tests.

Run PHY self-tests where available.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Some functions return an error code which is always 0.  Change their
return types to void and simplify their callers accordingly.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Make efx_process_channel() and falcon_process_eventq() return the
number of packets received rather than updating the quota, consistent
with new NAPI.

Since channels and RX queues are mapped one-to-one, remove return
value from falcon_handle_rx_event() and add a warning for events
with the wrong RX queue number.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

It is redundant with efx_channel::channel.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We have long since given up doing RSS on Falcon A1 and therefore we
would always write the default value of 0.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Rename efx_nic::rss_queues to the more obvious n_rx_queues

Remove efx_rx_queue::used and other stuff that's redundant with it.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

efx_channel::has_interrupt is redundant with efx_channel::used_flags.

Remove efx_test_eventq() because it is now obviously unreachable.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Extend the SPI device setup code to support this.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

gcc will automatically inline static functions with only one caller, and
may inline other functions depending on the kernel configuration and size
of the intermediate code.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Replace (cond ? 1 : 0) with cond or !!cond as appropriate, and
(cond ? 0 : 1) with !cond.

Remove some redundant boolean temporaries.

Rename one field that looks like a flag but isn't.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

These were clearly bogus.

From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We believed that some valid SNAP frames were being marked as invalid.
In fact this is not the case and no workaround is needed.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Checksum generation is an attribute of our hardware TX queues, not TX
descriptors.  We previously used a single queue and turned checksum
generation on or off as requested through ethtool.  However, this can
result in regenerating checksums in raw packets that should not be
modified.  We now create 2 hardware TX queues with checksum generation
on or off.  They are presented to the net core as one queue since it
does not know how to select between them.

The self-test verifies that a bad checksum is unaltered on the queue
with checksum generation off.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use of the net_device::priv field is deprecated.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

As recommended by Jean Delvare:
- Increase timeout to 50 ms
- Leave adapter class clear so that unwanted drivers do not probe our bus
- Use strlcpy() for name initialisation
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>