[ Upstream commit 170417c8c7bb2cbbdd949bf5c443c0c8f24a203b ]

Commit 345c0dbf3a30 ("ext4: protect journal inode's blocks using
block_validity") failed to add an exception for the journal inode in
ext4_check_blockref(), which is the function used by ext4_get_branch()
for indirect blocks.  This caused attempts to read from the ext3-style
journals to fail with:

[  848.968550] EXT4-fs error (device sdb7): ext4_get_branch:171: inode #8: block 30343695: comm jbd2/sdb7-8: invalid block

Fix this by adding the missing exception check.

Fixes: 345c0dbf3a30 ("ext4: protect journal inode's blocks using block_validity")
Reported-by: NArthur Marsh <arthur.marsh@internode.on.net>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 0a944e8a6c66ca04c7afbaa17e22bf208a8b37f0 ]

Since the journal inode is already checked when we added it to the
block validity's system zone, if we check it again, we'll just trigger
a failure.

This was causing failures like this:

[   53.897001] EXT4-fs error (device sda): ext4_find_extent:909: inode
#8: comm jbd2/sda-8: pblk 121667583 bad header/extent: invalid extent entries - magic f30a, entries 8, max 340(340), depth 0(0)
[   53.931430] jbd2_journal_bmap: journal block not found at offset 49 on sda-8
[   53.938480] Aborting journal on device sda-8.

... but only if the system was under enough memory pressure that
logical->physical mapping for the journal inode gets pushed out of the
extent cache.  (This is why it wasn't noticed earlier.)

Fixes: 345c0dbf3a30 ("ext4: protect journal inode's blocks using block_validity")
Reported-by: NDan Rue <dan.rue@linaro.org>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>
Tested-by: NNaresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 34ca26a98ad67edd6e4870fe2d4aa047d41a51dd ]

It appears when testing my previous fix for some of the legacy
modesetting issues with MST, I misattributed some kernel splats that
started appearing on my machine after a rebase as being from upstream.
But it appears they actually came from my patch series:

[    2.980512] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Updating routing for [CONNECTOR:65:eDP-1]
[    2.980516] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] [CONNECTOR:65:eDP-1] is not registered
[    2.980516] ------------[ cut here ]------------
[    2.980519] Could not determine valid watermarks for inherited state
[    2.980553] WARNING: CPU: 3 PID: 551 at drivers/gpu/drm/i915/intel_display.c:14983 intel_modeset_init+0x14d7/0x19f0 [i915]
[    2.980556] Modules linked in: i915(O+) i2c_algo_bit drm_kms_helper(O) syscopyarea sysfillrect sysimgblt fb_sys_fops drm(O) intel_rapl x86_pkg_temp_thermal iTCO_wdt wmi_bmof coretemp crc32_pclmul psmouse i2c_i801 mei_me mei i2c_core lpc_ich mfd_core tpm_tis tpm_tis_core wmi tpm thinkpad_acpi pcc_cpufreq video ehci_pci crc32c_intel serio_raw ehci_hcd xhci_pci xhci_hcd
[    2.980577] CPU: 3 PID: 551 Comm: systemd-udevd Tainted: G           O      4.19.0-rc7Lyude-Test+ #1
[    2.980579] Hardware name: LENOVO 20BWS1KY00/20BWS1KY00, BIOS JBET63WW (1.27 ) 11/10/2016
[    2.980605] RIP: 0010:intel_modeset_init+0x14d7/0x19f0 [i915]
[    2.980607] Code: 89 df e8 ec 27 02 00 e9 24 f2 ff ff be 03 00 00 00 48 89 df e8 da 27 02 00 e9 26 f2 ff ff 48 c7 c7 c8 d1 34 a0 e8 23 cf dc e0 <0f> 0b e9 7c fd ff ff f6 c4 04 0f 85 37 f7 ff ff 48 8b 83 60 08 00
[    2.980611] RSP: 0018:ffffc90000287988 EFLAGS: 00010282
[    2.980614] RAX: 0000000000000000 RBX: ffff88031b488000 RCX: 0000000000000006
[    2.980617] RDX: 0000000000000007 RSI: 0000000000000086 RDI: ffff880321ad54d0
[    2.980620] RBP: ffffc90000287a10 R08: 000000000000040a R09: 0000000000000065
[    2.980623] R10: ffff88030ebb8f00 R11: ffffffff81416590 R12: ffff88031b488000
[    2.980626] R13: ffff88031b4883a0 R14: ffffc900002879a8 R15: ffff880319099800
[    2.980630] FS:  00007f475620d180(0000) GS:ffff880321ac0000(0000) knlGS:0000000000000000
[    2.980633] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    2.980636] CR2: 00007f9ef28018a0 CR3: 000000031b72c001 CR4: 00000000003606e0
[    2.980639] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[    2.980642] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[    2.980645] Call Trace:
[    2.980675]  i915_driver_load+0xb0e/0xdc0 [i915]
[    2.980681]  ? kernfs_add_one+0xe7/0x130
[    2.980709]  i915_pci_probe+0x46/0x60 [i915]
[    2.980715]  pci_device_probe+0xd4/0x150
[    2.980719]  really_probe+0x243/0x3b0
[    2.980722]  driver_probe_device+0xba/0x100
[    2.980726]  __driver_attach+0xe4/0x110
[    2.980729]  ? driver_probe_device+0x100/0x100
[    2.980733]  bus_for_each_dev+0x74/0xb0
[    2.980736]  driver_attach+0x1e/0x20
[    2.980739]  bus_add_driver+0x159/0x230
[    2.980743]  ? 0xffffffffa0393000
[    2.980746]  driver_register+0x70/0xc0
[    2.980749]  ? 0xffffffffa0393000
[    2.980753]  __pci_register_driver+0x57/0x60
[    2.980780]  i915_init+0x55/0x58 [i915]
[    2.980785]  do_one_initcall+0x4a/0x1c4
[    2.980789]  ? do_init_module+0x27/0x210
[    2.980793]  ? kmem_cache_alloc_trace+0x131/0x190
[    2.980797]  do_init_module+0x60/0x210
[    2.980800]  load_module+0x2063/0x22e0
[    2.980804]  ? vfs_read+0x116/0x140
[    2.980807]  ? vfs_read+0x116/0x140
[    2.980811]  __do_sys_finit_module+0xbd/0x120
[    2.980814]  ? __do_sys_finit_module+0xbd/0x120
[    2.980818]  __x64_sys_finit_module+0x1a/0x20
[    2.980821]  do_syscall_64+0x5a/0x110
[    2.980824]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[    2.980826] RIP: 0033:0x7f4754e32879
[    2.980828] Code: 00 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d f7 45 2c 00 f7 d8 64 89 01 48
[    2.980831] RSP: 002b:00007fff43fd97d8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[    2.980834] RAX: ffffffffffffffda RBX: 0000559a44ca64f0 RCX: 00007f4754e32879
[    2.980836] RDX: 0000000000000000 RSI: 00007f475599f4cd RDI: 0000000000000018
[    2.980838] RBP: 00007f475599f4cd R08: 0000000000000000 R09: 0000000000000000
[    2.980839] R10: 0000000000000018 R11: 0000000000000246 R12: 0000000000000000
[    2.980841] R13: 0000559a44c92fd0 R14: 0000000000020000 R15: 0000000000000000
[    2.980881] WARNING: CPU: 3 PID: 551 at drivers/gpu/drm/i915/intel_display.c:14983 intel_modeset_init+0x14d7/0x19f0 [i915]
[    2.980884] ---[ end trace 5eb47a76277d4731 ]---

The cause of this appears to be due to the fact that if there's
pre-existing display state that was set by the BIOS when i915 loads, it
will attempt to perform a modeset before the driver is registered with
userspace. Since this happens before the driver's registered with
userspace, it's connectors are also unregistered and thus-states which
would turn on DPMS on a connector end up getting rejected since the
connector isn't registered.

These bugs managed to get past Intel's CI partially due to the fact it
never ran a full test on my patches for some reason, but also because
all of the tests unload the GPU once before running. Since this bug is
only really triggered when the drivers tries to perform a modeset before
it's been fully registered with userspace when coming from whatever
display configuration the firmware left us with, it likely would never
have been picked up by CI in the first place.

After some discussion with vsyrjala, we decided the best course of
action would be to just move the unregistered connector checks out of
update_connector_routing() and into drm_atomic_set_crtc_for_connector().
The reason for this being that legacy modesetting isn't going to be
expecting failures anywhere (at least this is the case with X), so
ideally we want to ensure that any DPMS changes will still work even on
unregistered connectors. Instead, we now only reject new modesets which
would change the current CRTC assigned to an unregistered connector
unless no new CRTC is being assigned to replace the connector's previous
one.
Signed-off-by: NLyude Paul <lyude@redhat.com>
Reported-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 4d80273976bf ("drm/atomic_helper: Disallow new modesets on unregistered connectors")
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181009204424.21462-1-lyude@redhat.com
(cherry picked from commit b5d29843d8ef86d4cde4742e095b81b7fd41e688)
Fixes: e96550956fbc ("drm/atomic_helper: Disallow new modesets on unregistered connectors")
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 4f419eb14272e0698e8c55bb5f3f266cc2a21c81 ]

The access to airq_areas was racy ever since the adapter interrupts got
introduced to virtio-ccw, but since commit 39c7dcb15892 ("virtio/s390:
make airq summary indicators DMA") this became an issue in practice as
well. Namely before that commit the airq_info that got overwritten was
still functional. After that commit however the two infos share a
summary_indicator, which aggravates the situation. Which means
auto-online mechanism occasionally hangs the boot with virtio_blk.
Signed-off-by: NHalil Pasic <pasic@linux.ibm.com>
Reported-by: NMarc Hartmayer <mhartmay@linux.ibm.com>
Reviewed-by: NCornelia Huck <cohuck@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 96b14536 ("virtio-ccw: virtio-ccw adapter interrupt support.")
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit a8f196a0fa6391a436f63f360a1fb57031fdf26c ]

On VLV/CHV there is some kind of linkage between the cdclk frequency
and the DP link frequency. The spec says:
"For DP audio configuration, cdclk frequency shall be set to
 meet the following requirements:
 DP Link Frequency(MHz) | Cdclk frequency(MHz)
 270                    | 320 or higher
 162                    | 200 or higher"

I suspect that would more accurately be expressed as
"cdclk >= DP link clock", and in any case we can express it like
that in the code because of the limited set of cdclk (200, 266,
320, 400 MHz) and link frequencies (162 and 270 MHz) we support.

Without this we can end up in a situation where the cdclk
is too low and enabling DP audio will kill the pipe. Happens
eg. with 2560x1440 modes where the 266MHz cdclk is sufficient
to pump the pixels (241.5 MHz dotclock) but is too low for
the DP audio due to the link frequency being 270 MHz.

v2: Spell out the cdclk and link frequencies we actually support

Cc: stable@vger.kernel.org
Tested-by: NStefan Gottwald <gottwald@igel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111149Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190717114536.22937-1-ville.syrjala@linux.intel.comAcked-by: NChris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit bffb31f73b29a60ef693842d8744950c2819851d)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 50a260e859964002dab162513a10f91ae9d3bcd3 ]

There is a race between mca_reap(), btree_node_free() and journal code
btree_flush_write(), which results very rare and strange deadlock or
panic and are very hard to reproduce.

Let me explain how the race happens. In btree_flush_write() one btree
node with oldest journal pin is selected, then it is flushed to cache
device, the select-and-flush is a two steps operation. Between these two
steps, there are something may happen inside the race window,
- The selected btree node was reaped by mca_reap() and allocated to
  other requesters for other btree node.
- The slected btree node was selected, flushed and released by mca
  shrink callback bch_mca_scan().
When btree_flush_write() tries to flush the selected btree node, firstly
b->write_lock is held by mutex_lock(). If the race happens and the
memory of selected btree node is allocated to other btree node, if that
btree node's write_lock is held already, a deadlock very probably
happens here. A worse case is the memory of the selected btree node is
released, then all references to this btree node (e.g. b->write_lock)
will trigger NULL pointer deference panic.

This race was introduced in commit cafe5635 ("bcache: A block layer
cache"), and enlarged by commit c4dc2497 ("bcache: fix high CPU
occupancy during journal"), which selected 128 btree nodes and flushed
them one-by-one in a quite long time period.

Such race is not easy to reproduce before. On a Lenovo SR650 server with
48 Xeon cores, and configure 1 NVMe SSD as cache device, a MD raid0
device assembled by 3 NVMe SSDs as backing device, this race can be
observed around every 10,000 times btree_flush_write() gets called. Both
deadlock and kernel panic all happened as aftermath of the race.

The idea of the fix is to add a btree flag BTREE_NODE_journal_flush. It
is set when selecting btree nodes, and cleared after btree nodes
flushed. Then when mca_reap() selects a btree node with this bit set,
this btree node will be skipped. Since mca_reap() only reaps btree node
without BTREE_NODE_journal_flush flag, such race is avoided.

Once corner case should be noticed, that is btree_node_free(). It might
be called in some error handling code path. For example the following
code piece from btree_split(),
        2149 err_free2:
        2150         bkey_put(b->c, &n2->key);
        2151         btree_node_free(n2);
        2152         rw_unlock(true, n2);
        2153 err_free1:
        2154         bkey_put(b->c, &n1->key);
        2155         btree_node_free(n1);
        2156         rw_unlock(true, n1);
At line 2151 and 2155, the btree node n2 and n1 are released without
mac_reap(), so BTREE_NODE_journal_flush also needs to be checked here.
If btree_node_free() is called directly in such error handling path,
and the selected btree node has BTREE_NODE_journal_flush bit set, just
delay for 1 us and retry again. In this case this btree node won't
be skipped, just retry until the BTREE_NODE_journal_flush bit cleared,
and free the btree node memory.

Fixes: cafe5635 ("bcache: A block layer cache")
Signed-off-by: NColy Li <colyli@suse.de>
Reported-and-tested-by: Nkbuild test robot <lkp@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 41508bb7d46b74dba631017e5a702a86caf1db8c ]

When accessing or modifying BTREE_NODE_dirty bit, it is not always
necessary to acquire b->write_lock. In bch_btree_cache_free() and
mca_reap() acquiring b->write_lock is necessary, and this patch adds
comments to explain why mutex_lock(&b->write_lock) is necessary for
checking or clearing BTREE_NODE_dirty bit there.
Signed-off-by: NColy Li <colyli@suse.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e5ec5f4765ada9c75fb3eee93a6e72f0e50599d5 ]

In bch_btree_cache_free() and btree_node_free(), BTREE_NODE_dirty is
always set no matter btree node is dirty or not. The code looks like
this,
	if (btree_node_dirty(b))
		btree_complete_write(b, btree_current_write(b));
	clear_bit(BTREE_NODE_dirty, &b->flags);

Indeed if btree_node_dirty(b) returns false, it means BTREE_NODE_dirty
bit is cleared, then it is unnecessary to clear the bit again.

This patch only clears BTREE_NODE_dirty when btree_node_dirty(b) is
true (the bit is set), to save a few CPU cycles.
Signed-off-by: NColy Li <colyli@suse.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 5eb8d18ca0e001c6055da2b7f30d8f6dca23a44f ]

Once we clear the NFS_DELEGATED_STATE flag, we're telling
nfs_delegation_claim_opens() that we're done recovering all open state
for that stateid, so we really need to ensure that we test for all
open modes that are currently cached and recover them before exiting
nfs4_open_delegation_recall().

Fixes: 24311f88 ("NFSv4: Recovery of recalled read delegations...")
Signed-off-by: NTrond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 90c6260c1905a68fb596844087f2223bd4657fee ]

gcc-9 complains about a blatant uninitialized variable use that
all earlier compiler versions missed:

drivers/iio/adc/rcar-gyroadc.c:510:5: warning: 'ret' may be used uninitialized in this function [-Wmaybe-uninitialized]

Return -EINVAL instead here and a few lines above it where
we accidentally return 0 on failure.

Cc: stable@vger.kernel.org
Fixes: 059c53b3 ("iio: adc: Add Renesas GyroADC driver")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NJonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 7b358c6f12dc82364f6d317f8c8f1d794adbc3f5 ]

When CONFIG_MIGRATE_VMA_HELPER is enabled, migrate_vma() calls
migrate_vma_collect() which initializes a struct mm_walk but didn't
initialize mm_walk.pud_entry.  (Found by code inspection) Use a C
structure initialization to make sure it is set to NULL.

Link: http://lkml.kernel.org/r/20190719233225.12243-1-rcampbell@nvidia.com
Fixes: 8763cb45 ("mm/migrate: new memory migration helper for use with device memory")
Signed-off-by: NRalph Campbell <rcampbell@nvidia.com>
Reviewed-by: NJohn Hubbard <jhubbard@nvidia.com>
Reviewed-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit b1ac6704493fa14b5dc19eb6b69a73932361a131 ]

In SAMA5D2 datasheet, TWIHS_CWGR register rescription mentions clock
offset of 3 cycles (compared to 4 in eg. SAMA5D3).

Cc: stable@vger.kernel.org # 5.2.x
[needs applying to i2c-at91.c instead for earlier kernels]
Fixes: 0ef6f321 ("i2c: at91: add support for new alternative command mode")
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: NLudovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit d12e3aae160fb26b534c4496b211d6e60a5179ed ]

Driver was not disabling TXRDY interrupt after last TX byte.
This caused interrupt storm until transfer timeouts for slow
or broken device on the bus. The patch fixes the interrupt storm
on my SAMA5D2-based board.

Cc: stable@vger.kernel.org # 5.2.x
[v5.2 introduced file split; the patch should apply to i2c-at91.c before the split]
Fixes: fac368a0 ("i2c: at91: add new driver")
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: NLudovic Desroches <ludovic.desroches@microchip.com>
Tested-by: NRaag Jadav <raagjadav@gmail.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit ffe0bbabb0cffceceae07484fde1ec2a63b1537c ]

If gpiolib is disabled, we use the inline stubs from gpio/consumer.h
instead of regular definitions of GPIO API. The stubs for 'optional'
variants of gpiod_get routines return NULL in this case as if the
relevant GPIO wasn't found. This is correct so far.

Calling other (non-gpio_get) stubs from this header triggers a warning
because the GPIO descriptor couldn't have been requested. The warning
however is unconditional (WARN_ON(1)) and is emitted even if the passed
descriptor pointer is NULL.

We don't want to force the users of 'optional' gpio_get to check the
returned pointer before calling e.g. gpiod_set_value() so let's only
WARN on non-NULL descriptors.

Cc: stable@vger.kernel.org
Reported-by: NClaus H. Stovgaard <cst@phaseone.com>
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 9eed17d37c77171cf5ffb95c4257f87df3cd4c8f ]

Since the cached32_node is allowed to be advanced above dma_32bit_pfn
(to provide a shortcut into the limited range), we need to be careful to
remove the to be freed node if it is the cached32_node.

[   48.477773] BUG: KASAN: use-after-free in __cached_rbnode_delete_update+0x68/0x110
[   48.477812] Read of size 8 at addr ffff88870fc19020 by task kworker/u8:1/37
[   48.477843]
[   48.477879] CPU: 1 PID: 37 Comm: kworker/u8:1 Tainted: G     U            5.2.0+ #735
[   48.477915] Hardware name: Intel Corporation NUC7i5BNK/NUC7i5BNB, BIOS BNKBL357.86A.0052.2017.0918.1346 09/18/2017
[   48.478047] Workqueue: i915 __i915_gem_free_work [i915]
[   48.478075] Call Trace:
[   48.478111]  dump_stack+0x5b/0x90
[   48.478137]  print_address_description+0x67/0x237
[   48.478178]  ? __cached_rbnode_delete_update+0x68/0x110
[   48.478212]  __kasan_report.cold.3+0x1c/0x38
[   48.478240]  ? __cached_rbnode_delete_update+0x68/0x110
[   48.478280]  ? __cached_rbnode_delete_update+0x68/0x110
[   48.478308]  __cached_rbnode_delete_update+0x68/0x110
[   48.478344]  private_free_iova+0x2b/0x60
[   48.478378]  iova_magazine_free_pfns+0x46/0xa0
[   48.478403]  free_iova_fast+0x277/0x340
[   48.478443]  fq_ring_free+0x15a/0x1a0
[   48.478473]  queue_iova+0x19c/0x1f0
[   48.478597]  cleanup_page_dma.isra.64+0x62/0xb0 [i915]
[   48.478712]  __gen8_ppgtt_cleanup+0x63/0x80 [i915]
[   48.478826]  __gen8_ppgtt_cleanup+0x42/0x80 [i915]
[   48.478940]  __gen8_ppgtt_clear+0x433/0x4b0 [i915]
[   48.479053]  __gen8_ppgtt_clear+0x462/0x4b0 [i915]
[   48.479081]  ? __sg_free_table+0x9e/0xf0
[   48.479116]  ? kfree+0x7f/0x150
[   48.479234]  i915_vma_unbind+0x1e2/0x240 [i915]
[   48.479352]  i915_vma_destroy+0x3a/0x280 [i915]
[   48.479465]  __i915_gem_free_objects+0xf0/0x2d0 [i915]
[   48.479579]  __i915_gem_free_work+0x41/0xa0 [i915]
[   48.479607]  process_one_work+0x495/0x710
[   48.479642]  worker_thread+0x4c7/0x6f0
[   48.479687]  ? process_one_work+0x710/0x710
[   48.479724]  kthread+0x1b2/0x1d0
[   48.479774]  ? kthread_create_worker_on_cpu+0xa0/0xa0
[   48.479820]  ret_from_fork+0x1f/0x30
[   48.479864]
[   48.479907] Allocated by task 631:
[   48.479944]  save_stack+0x19/0x80
[   48.479994]  __kasan_kmalloc.constprop.6+0xc1/0xd0
[   48.480038]  kmem_cache_alloc+0x91/0xf0
[   48.480082]  alloc_iova+0x2b/0x1e0
[   48.480125]  alloc_iova_fast+0x58/0x376
[   48.480166]  intel_alloc_iova+0x90/0xc0
[   48.480214]  intel_map_sg+0xde/0x1f0
[   48.480343]  i915_gem_gtt_prepare_pages+0xb8/0x170 [i915]
[   48.480465]  huge_get_pages+0x232/0x2b0 [i915]
[   48.480590]  ____i915_gem_object_get_pages+0x40/0xb0 [i915]
[   48.480712]  __i915_gem_object_get_pages+0x90/0xa0 [i915]
[   48.480834]  i915_gem_object_prepare_write+0x2d6/0x330 [i915]
[   48.480955]  create_test_object.isra.54+0x1a9/0x3e0 [i915]
[   48.481075]  igt_shared_ctx_exec+0x365/0x3c0 [i915]
[   48.481210]  __i915_subtests.cold.4+0x30/0x92 [i915]
[   48.481341]  __run_selftests.cold.3+0xa9/0x119 [i915]
[   48.481466]  i915_live_selftests+0x3c/0x70 [i915]
[   48.481583]  i915_pci_probe+0xe7/0x220 [i915]
[   48.481620]  pci_device_probe+0xe0/0x180
[   48.481665]  really_probe+0x163/0x4e0
[   48.481710]  device_driver_attach+0x85/0x90
[   48.481750]  __driver_attach+0xa5/0x180
[   48.481796]  bus_for_each_dev+0xda/0x130
[   48.481831]  bus_add_driver+0x205/0x2e0
[   48.481882]  driver_register+0xca/0x140
[   48.481927]  do_one_initcall+0x6c/0x1af
[   48.481970]  do_init_module+0x106/0x350
[   48.482010]  load_module+0x3d2c/0x3ea0
[   48.482058]  __do_sys_finit_module+0x110/0x180
[   48.482102]  do_syscall_64+0x62/0x1f0
[   48.482147]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[   48.482190]
[   48.482224] Freed by task 37:
[   48.482273]  save_stack+0x19/0x80
[   48.482318]  __kasan_slab_free+0x12e/0x180
[   48.482363]  kmem_cache_free+0x70/0x140
[   48.482406]  __free_iova+0x1d/0x30
[   48.482445]  fq_ring_free+0x15a/0x1a0
[   48.482490]  queue_iova+0x19c/0x1f0
[   48.482624]  cleanup_page_dma.isra.64+0x62/0xb0 [i915]
[   48.482749]  __gen8_ppgtt_cleanup+0x63/0x80 [i915]
[   48.482873]  __gen8_ppgtt_cleanup+0x42/0x80 [i915]
[   48.482999]  __gen8_ppgtt_clear+0x433/0x4b0 [i915]
[   48.483123]  __gen8_ppgtt_clear+0x462/0x4b0 [i915]
[   48.483250]  i915_vma_unbind+0x1e2/0x240 [i915]
[   48.483378]  i915_vma_destroy+0x3a/0x280 [i915]
[   48.483500]  __i915_gem_free_objects+0xf0/0x2d0 [i915]
[   48.483622]  __i915_gem_free_work+0x41/0xa0 [i915]
[   48.483659]  process_one_work+0x495/0x710
[   48.483704]  worker_thread+0x4c7/0x6f0
[   48.483748]  kthread+0x1b2/0x1d0
[   48.483787]  ret_from_fork+0x1f/0x30
[   48.483831]
[   48.483868] The buggy address belongs to the object at ffff88870fc19000
[   48.483868]  which belongs to the cache iommu_iova of size 40
[   48.483920] The buggy address is located 32 bytes inside of
[   48.483920]  40-byte region [ffff88870fc19000, ffff88870fc19028)
[   48.483964] The buggy address belongs to the page:
[   48.484006] page:ffffea001c3f0600 refcount:1 mapcount:0 mapping:ffff8888181a91c0 index:0x0 compound_mapcount: 0
[   48.484045] flags: 0x8000000000010200(slab|head)
[   48.484096] raw: 8000000000010200 ffffea001c421a08 ffffea001c447e88 ffff8888181a91c0
[   48.484141] raw: 0000000000000000 0000000000120012 00000001ffffffff 0000000000000000
[   48.484188] page dumped because: kasan: bad access detected
[   48.484230]
[   48.484265] Memory state around the buggy address:
[   48.484314]  ffff88870fc18f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[   48.484361]  ffff88870fc18f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[   48.484406] >ffff88870fc19000: fb fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc
[   48.484451]                                ^
[   48.484494]  ffff88870fc19080: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[   48.484530]  ffff88870fc19100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108602
Fixes: e60aa7b5 ("iommu/iova: Extend rbtree node caching")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: <stable@vger.kernel.org> # v4.15+
Reviewed-by: NRobin Murphy <robin.murphy@arm.com>
Signed-off-by: NJoerg Roedel <jroedel@suse.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit da0ef93310e67ae6902efded60b6724dab27a5d1 ]

The virtual real mode addressing (VRMA) mechanism is used when a
partition is using HPT (Hash Page Table) translation and performs real
mode accesses (MSR[IR|DR] = 0) in non-hypervisor mode. In this mode
effective address bits 0:23 are treated as zero (i.e. the access is
aliased to 0) and the access is performed using an implicit 1TB SLB
entry.

The size of the RMA (Real Memory Area) is communicated to the guest as
the size of the first memory region in the device tree. And because of
the mechanism described above can be expected to not exceed 1TB. In
the event that the host erroneously represents the RMA as being larger
than 1TB, guest accesses in real mode to memory addresses above 1TB
will be aliased down to below 1TB. This means that a memory access
performed in real mode may differ to one performed in virtual mode for
the same memory address, which would likely have unintended
consequences.

To avoid this outcome have the guest explicitly limit the size of the
RMA to the current maximum, which is 1TB. This means that even if the
first memory block is larger than 1TB, only the first 1TB should be
accessed in real mode.

Fixes: c610d65c ("powerpc/pseries: lift RTAS limit for hash")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: NSuraj Jitindar Singh <sjitindarsingh@gmail.com>
Tested-by: NSatheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190710052018.14628-1-sjitindarsingh@gmail.comSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 2756d9143aa517b97961e85412882b8ce31371a6 ]

It turned out that the recent Intel HD-audio controller chips show a
significant stall during the system PM resume intermittently.  It
doesn't happen so often and usually it may read back successfully
after one or more seconds, but in some rare worst cases the driver
went into fallback mode.

After trial-and-error, we found out that the communication stall seems
covered by issuing the sync after each verb write, as already done for
AMD and other chipsets.  So this patch enables the write-sync flag for
the recent Intel chips, Skylake and onward, as a workaround.

Also, since Broxton and co have the very same driver flags as Skylake,
refer to the Skylake driver flags instead of defining the same
contents again for simplification.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201901Reported-and-tested-by: NTodd Brandt <todd.e.brandt@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c479450f61c7f1f248c9a54aedacd2a6ca521ff8 ]

This patch adds support for the Armadeus ST0700 Adapt. It comes with a
Santek ST0700I5Y-RBSLW 7.0" WVGA (800x480) TFT and an adapter board so
that it can be connected on the TFT header of Armadeus Dev boards.

Cc: stable@vger.kernel.org # v4.19
Reviewed-by: NRob Herring <robh@kernel.org>
Signed-off-by: NSébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507152713.27494-1-sebastien.szymanski@armadeus.comSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 54fa16ee532705985e6c946da455856f18f63ee1 ]

Check if in fail_io mode at start of dm_pool_metadata_set_needs_check().
Otherwise dm_pool_metadata_set_needs_check()'s superblock_lock() can
crash in dm_bm_write_lock() while accessing the block manager object
that was previously destroyed as part of a failed
dm_pool_abort_metadata() that ultimately set fail_io to begin with.

Also, update DMERR() message to more accurately describe
superblock_lock() failure.

Cc: stable@vger.kernel.org
Reported-by: NZdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 4c6d80e1144bdf48cae6b602ae30d41f3e5c76a9 ]

The pstore_mkfile() function is passed a pointer to a struct
pstore_record. On success it consumes this 'record' pointer and
references it from the created inode.

On failure, however, it may or may not free the record. There are even
two different code paths which return -ENOMEM -- one of which does and
the other doesn't free the record.

Make the behaviour deterministic by never consuming and freeing the
record when returning failure, allowing the caller to do the cleanup
consistently.
Signed-off-by: NNorbert Manthey <nmanthey@amazon.de>
Link: https://lore.kernel.org/r/1562331960-26198-1-git-send-email-nmanthey@amazon.de
Fixes: 83f70f07 ("pstore: Do not duplicate record metadata")
Fixes: 1dfff7dd ("pstore: Pass record contents instead of copying")
Cc: stable@vger.kernel.org
[kees: also move "private" allocation location, rename inode cleanup label]
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 49f17c26c123b60fd1c74629eef077740d16ffc2 ]

Since resources can be removed, locking should ensure that the resource
is not removed while accessing it.  However, find_next_iomem_res() does
not hold the lock while copying the data of the resource.

Keep holding the lock while the data is copied.  While at it, change the
return value to a more informative value.  It is disregarded by the
callers.

[akpm@linux-foundation.org: fix find_next_iomem_res() documentation]
Link: http://lkml.kernel.org/r/20190613045903.4922-2-namit@vmware.com
Fixes: ff3cc952 ("resource: Add remove_resource interface")
Signed-off-by: NNadav Amit <namit@vmware.com>
Reviewed-by: NAndrew Morton <akpm@linux-foundation.org>
Reviewed-by: NDan Williams <dan.j.williams@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 010a93bf97c72f43aac664d0a685942f83d1a103 ]

Previously find_next_iomem_res() used "*res" as both an input parameter for
the range to search and the type of resource to search for, and an output
parameter for the resource we found, which makes the interface confusing.

The current callers use find_next_iomem_res() incorrectly because they
allocate a single struct resource and use it for repeated calls to
find_next_iomem_res().  When find_next_iomem_res() returns a resource, it
overwrites the start, end, flags, and desc members of the struct.  If we
call find_next_iomem_res() again, we must update or restore these fields.
The previous code restored res.start and res.end, but not res.flags or
res.desc.

Since the callers did not restore res.flags, if they searched for flags
IORESOURCE_MEM | IORESOURCE_BUSY and found a resource with flags
IORESOURCE_MEM | IORESOURCE_BUSY | IORESOURCE_SYSRAM, the next search would
incorrectly skip resources unless they were also marked as
IORESOURCE_SYSRAM.

Fix this by restructuring the interface so it takes explicit "start, end,
flags" parameters and uses "*res" only as an output parameter.

Based on a patch by Lianbo Jiang <lijiang@redhat.com>.

 [ bp: While at it:
   - make comments kernel-doc style.
   -

Originally-by: http://lore.kernel.org/lkml/20180921073211.20097-2-lijiang@redhat.comSigned-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NBorislav Petkov <bp@suse.de>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Brijesh Singh <brijesh.singh@amd.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: H. Peter Anvin <hpa@zytor.com>
CC: Lianbo Jiang <lijiang@redhat.com>
CC: Takashi Iwai <tiwai@suse.de>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Vivek Goyal <vgoyal@redhat.com>
CC: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
CC: bhe@redhat.com
CC: dan.j.williams@intel.com
CC: dyoung@redhat.com
CC: kexec@lists.infradead.org
CC: mingo@redhat.com
CC: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/153805812916.1157.177580438135143788.stgit@bhelgaas-glaptop.roam.corp.google.comSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit a98959fdbda1849a01b2150bb635ed559ec06700 ]

find_next_iomem_res() finds an iomem resource that covers part of a range
described by "start, end".  All callers expect that range to be inclusive,
i.e., both start and end are included, but find_next_iomem_res() doesn't
handle the end address correctly.

If it finds an iomem resource that contains exactly the end address, it
skips it, e.g., if "start, end" is [0x0-0x10000] and there happens to be an
iomem resource [mem 0x10000-0x10000] (the single byte at 0x10000), we skip
it:

  find_next_iomem_res(...)
  {
    start = 0x0;
    end = 0x10000;
    for (p = next_resource(...)) {
      # p->start = 0x10000;
      # p->end = 0x10000;
      # we *should* return this resource, but this condition is false:
      if ((p->end >= start) && (p->start < end))
        break;

Adjust find_next_iomem_res() so it allows a resource that includes the
single byte at the end of the range.  This is a corner case that we
probably don't see in practice.

Fixes: 58c1b5b0 ("[PATCH] memory hotadd fixes: find_next_system_ram catch range fix")
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NBorislav Petkov <bp@suse.de>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Brijesh Singh <brijesh.singh@amd.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: H. Peter Anvin <hpa@zytor.com>
CC: Lianbo Jiang <lijiang@redhat.com>
CC: Takashi Iwai <tiwai@suse.de>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Vivek Goyal <vgoyal@redhat.com>
CC: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
CC: bhe@redhat.com
CC: dan.j.williams@intel.com
CC: dyoung@redhat.com
CC: kexec@lists.infradead.org
CC: mingo@redhat.com
CC: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/153805812254.1157.16736368485811773752.stgit@bhelgaas-glaptop.roam.corp.google.comSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit aa53e3bfac7205fb3a8815ac1c937fd6ed01b41e ]

Nikolay reported the following KASAN splat when running btrfs/048:

[ 1843.470920] ==================================================================
[ 1843.471971] BUG: KASAN: slab-out-of-bounds in strncmp+0x66/0xb0
[ 1843.472775] Read of size 1 at addr ffff888111e369e2 by task btrfs/3979

[ 1843.473904] CPU: 3 PID: 3979 Comm: btrfs Not tainted 5.2.0-rc3-default #536
[ 1843.475009] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[ 1843.476322] Call Trace:
[ 1843.476674]  dump_stack+0x7c/0xbb
[ 1843.477132]  ? strncmp+0x66/0xb0
[ 1843.477587]  print_address_description+0x114/0x320
[ 1843.478256]  ? strncmp+0x66/0xb0
[ 1843.478740]  ? strncmp+0x66/0xb0
[ 1843.479185]  __kasan_report+0x14e/0x192
[ 1843.479759]  ? strncmp+0x66/0xb0
[ 1843.480209]  kasan_report+0xe/0x20
[ 1843.480679]  strncmp+0x66/0xb0
[ 1843.481105]  prop_compression_validate+0x24/0x70
[ 1843.481798]  btrfs_xattr_handler_set_prop+0x65/0x160
[ 1843.482509]  __vfs_setxattr+0x71/0x90
[ 1843.483012]  __vfs_setxattr_noperm+0x84/0x130
[ 1843.483606]  vfs_setxattr+0xac/0xb0
[ 1843.484085]  setxattr+0x18c/0x230
[ 1843.484546]  ? vfs_setxattr+0xb0/0xb0
[ 1843.485048]  ? __mod_node_page_state+0x1f/0xa0
[ 1843.485672]  ? _raw_spin_unlock+0x24/0x40
[ 1843.486233]  ? __handle_mm_fault+0x988/0x1290
[ 1843.486823]  ? lock_acquire+0xb4/0x1e0
[ 1843.487330]  ? lock_acquire+0xb4/0x1e0
[ 1843.487842]  ? mnt_want_write_file+0x3c/0x80
[ 1843.488442]  ? debug_lockdep_rcu_enabled+0x22/0x40
[ 1843.489089]  ? rcu_sync_lockdep_assert+0xe/0x70
[ 1843.489707]  ? __sb_start_write+0x158/0x200
[ 1843.490278]  ? mnt_want_write_file+0x3c/0x80
[ 1843.490855]  ? __mnt_want_write+0x98/0xe0
[ 1843.491397]  __x64_sys_fsetxattr+0xba/0xe0
[ 1843.492201]  ? trace_hardirqs_off_thunk+0x1a/0x1c
[ 1843.493201]  do_syscall_64+0x6c/0x230
[ 1843.493988]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 1843.495041] RIP: 0033:0x7fa7a8a7707a
[ 1843.495819] Code: 48 8b 0d 21 de 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 be 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d ee dd 2b 00 f7 d8 64 89 01 48
[ 1843.499203] RSP: 002b:00007ffcb73bca38 EFLAGS: 00000202 ORIG_RAX: 00000000000000be
[ 1843.500210] RAX: ffffffffffffffda RBX: 00007ffcb73bda9d RCX: 00007fa7a8a7707a
[ 1843.501170] RDX: 00007ffcb73bda9d RSI: 00000000006dc050 RDI: 0000000000000003
[ 1843.502152] RBP: 00000000006dc050 R08: 0000000000000000 R09: 0000000000000000
[ 1843.503109] R10: 0000000000000002 R11: 0000000000000202 R12: 00007ffcb73bda91
[ 1843.504055] R13: 0000000000000003 R14: 00007ffcb73bda82 R15: ffffffffffffffff

[ 1843.505268] Allocated by task 3979:
[ 1843.505771]  save_stack+0x19/0x80
[ 1843.506211]  __kasan_kmalloc.constprop.5+0xa0/0xd0
[ 1843.506836]  setxattr+0xeb/0x230
[ 1843.507264]  __x64_sys_fsetxattr+0xba/0xe0
[ 1843.507886]  do_syscall_64+0x6c/0x230
[ 1843.508429]  entry_SYSCALL_64_after_hwframe+0x49/0xbe

[ 1843.509558] Freed by task 0:
[ 1843.510188] (stack is not available)

[ 1843.511309] The buggy address belongs to the object at ffff888111e369e0
                which belongs to the cache kmalloc-8 of size 8
[ 1843.514095] The buggy address is located 2 bytes inside of
                8-byte region [ffff888111e369e0, ffff888111e369e8)
[ 1843.516524] The buggy address belongs to the page:
[ 1843.517561] page:ffff88813f478d80 refcount:1 mapcount:0 mapping:ffff88811940c300 index:0xffff888111e373b8 compound_mapcount: 0
[ 1843.519993] flags: 0x4404000010200(slab|head)
[ 1843.520951] raw: 0004404000010200 ffff88813f48b008 ffff888119403d50 ffff88811940c300
[ 1843.522616] raw: ffff888111e373b8 000000000016000f 00000001ffffffff 0000000000000000
[ 1843.524281] page dumped because: kasan: bad access detected

[ 1843.525936] Memory state around the buggy address:
[ 1843.526975]  ffff888111e36880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1843.528479]  ffff888111e36900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1843.530138] >ffff888111e36980: fc fc fc fc fc fc fc fc fc fc fc fc 02 fc fc fc
[ 1843.531877]                                                        ^
[ 1843.533287]  ffff888111e36a00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1843.534874]  ffff888111e36a80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1843.536468] ==================================================================

This is caused by supplying a too short compression value ('lz') in the
test-case and comparing it to 'lzo' with strncmp() and a length of 3.
strncmp() read past the 'lz' when looking for the 'o' and thus caused an
out-of-bounds read.

Introduce a new check 'btrfs_compress_is_valid_type()' which not only
checks the user-supplied value against known compression types, but also
employs checks for too short values.
Reported-by: NNikolay Borisov <nborisov@suse.com>
Fixes: 272e5326c783 ("btrfs: prop: fix vanished compression property after failed set")
CC: stable@vger.kernel.org # 5.1+
Reviewed-by: NNikolay Borisov <nborisov@suse.com>
Signed-off-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit bcef5b7215681250c4bf8961dfe15e9e4fef97d0 ]

The function srp_parse_in() is used both for parsing source address
specifications and for target address specifications. Target addresses
must have a port number. Having to specify a port number for source
addresses is inconvenient. Make sure that srp_parse_in() supports again
parsing addresses with no port number.

Cc: <stable@vger.kernel.org>
Fixes: c62adb7d ("IB/srp: Fix IPv6 address parsing")
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e37df2d5b569390e3b80ebed9a73fd5b9dcda010 ]

This patch avoids that a warning is reported when building with W=1.

Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit f90b8fda3a9d72a9422ea80ae95843697f94ea4a ]

The SPI to the display on the DIR-685 is active low, we were
just saved by the SPI library enforcing active low on everything
before, so set it as active low to avoid ambiguity.

Link: https://lore.kernel.org/r/20190715202101.16060-1-linus.walleij@linaro.org
Cc: stable@vger.kernel.org
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 3fefd1cd95df04da67c83c1cb93b663f04b3324f ]

When emulating tsr, treclaim and trechkpt, we incorrectly set CR0. The
code currently sets:
    CR0 <- 00 || MSR[TS]
but according to the ISA it should be:
    CR0 <-  0 || MSR[TS] || 0

This fixes the bit shift to put the bits in the correct location.

This is a data integrity issue as CR0 is corrupted.

Fixes: 4bb3c7a0 ("KVM: PPC: Book3S HV: Work around transactional memory bugs in POWER9")
Cc: stable@vger.kernel.org # v4.17+
Tested-by: NSuraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit fd0944baad806dfb4c777124ec712c55b714ff51 ]

When the 'regs' field was added to struct kvm_vcpu_arch, the code
was changed to use several of the fields inside regs (e.g., gpr, lr,
etc.) but not the ccr field, because the ccr field in struct pt_regs
is 64 bits on 64-bit platforms, but the cr field in kvm_vcpu_arch is
only 32 bits.  This changes the code to use the regs.ccr field
instead of cr, and changes the assembly code on 64-bit platforms to
use 64-bit loads and stores instead of 32-bit ones.
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 4d763b168e9c5c366b05812c7bba7662e5ea3669 ]

Raise #GP when guest read/write IA32_XSS, but the CPUID bits
say that it shouldn't exist.

Fixes: 20300099 (kvm: vmx: add MSR logic for XSAVES)
Reported-by: NXiaoyao Li <xiaoyao.li@linux.intel.com>
Reported-by: NTao Xu <tao3.xu@intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NWanpeng Li <wanpengli@tencent.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit beb8d93b3e423043e079ef3dda19dad7b28467a8 ]

A previous fix to prevent KVM from consuming stale VMCS state after a
failed VM-Entry inadvertantly blocked KVM's handling of machine checks
that occur during VM-Entry.

Per Intel's SDM, a #MC during VM-Entry is handled in one of three ways,
depending on when the #MC is recognoized.  As it pertains to this bug
fix, the third case explicitly states EXIT_REASON_MCE_DURING_VMENTRY
is handled like any other VM-Exit during VM-Entry, i.e. sets bit 31 to
indicate the VM-Entry failed.

If a machine-check event occurs during a VM entry, one of the following occurs:
 - The machine-check event is handled as if it occurred before the VM entry:
        ...
 - The machine-check event is handled after VM entry completes:
        ...
 - A VM-entry failure occurs as described in Section 26.7. The basic
   exit reason is 41, for "VM-entry failure due to machine-check event".

Explicitly handle EXIT_REASON_MCE_DURING_VMENTRY as a one-off case in
vmx_vcpu_run() instead of binning it into vmx_complete_atomic_exit().
Doing so allows vmx_vcpu_run() to handle VMX_EXIT_REASONS_FAILED_VMENTRY
in a sane fashion and also simplifies vmx_complete_atomic_exit() since
VMCS.VM_EXIT_INTR_INFO is guaranteed to be fresh.

Fixes: b060ca3b ("kvm: vmx: Handle VMLAUNCH/VMRESUME failure properly")
Cc: stable@vger.kernel.org
Signed-off-by: NSean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: NJim Mattson <jmattson@google.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit d28f4290b53a157191ed9991ad05dffe9e8c0c89 ]

The behavior of WRMSR is in no way dependent on whether or not KVM
consumes the value.

Fixes: 4566654b ("KVM: vmx: Inject #GP on invalid PAT CR")
Cc: stable@vger.kernel.org
Cc: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: NSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 674ea351cdeb01d2740edce31db7f2d79ce6095d ]

This check will soon be done on every nested vmentry and vmexit,
"parallelize" it using bitwise operations.
Reviewed-by: NSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 87bc5b895d94a0f40fe170d4cf5771c8e8f85d15 ]

remove_session_caps() relies on __wait_on_freeing_inode(), to wait for
freeing inode to remove its caps. But VFS wakes freeing inode waiters
before calling destroy_inode().

Cc: stable@vger.kernel.org
Link: https://tracker.ceph.com/issues/40102Signed-off-by: N"Yan, Zheng" <zyan@redhat.com>
Reviewed-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 4914da2fb0c89205790503f20dfdde854f3afdd8 ]

We apply the codec resume forcibly at system resume callback for
updating and syncing the jack detection state that may have changed
during sleeping.  This is, however, superfluous for the codec like
Intel HDMI/DP, where the jack detection is managed via the audio
component notification; i.e. the jack state change shall be reported
sooner or later from the graphics side at mode change.

This patch changes the codec resume callback to avoid the forcible
resume conditionally with a new flag, codec->relaxed_resume, for
reducing the resume time.  The flag is set in the codec probe.

Although this doesn't fix the entire bug mentioned in the bugzilla
entry below, it's still a good optimization and some improvements are
seen.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201901
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 29fbeb7a908a60a5ae8c50fbe171cb8fdcef1980 ]

Fix mount options comparison when serverino option is turned off later
in cifs_autodisable_serverino() and thus avoiding mismatch of new cifs
mounts.

Cc: stable@vger.kernel.org
Signed-off-by: NPaulo Alcantara (SUSE) <paulo@paulo.ac>
Signed-off-by: NSteve French <stfrench@microsoft.com>
Reviewed-by: NPavel Shilovsky <pshilove@microsoft.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 106d45f350c7cac876844dc685845cba4ffdb70b ]

When tracing instances where we open and close WKA ports, we also pass the
request-ID of the respective FSF command.

But after successfully sending the FSF command we must not use the
request-object anymore, as this might result in an use-after-free (see
"zfcp: fix request object use-after-free in send path causing seqno
errors" ).

To fix this add a new variable that caches the request-ID before sending
the request. This won't change during the hand-off to the FCP channel,
and so it's safe to trace this cached request-ID later, instead of using
the request object.
Signed-off-by: NBenjamin Block <bblock@linux.ibm.com>
Fixes: d27a7cb9 ("zfcp: trace on request for open and close of WKA port")
Cc: <stable@vger.kernel.org> #2.6.38+
Reviewed-by: NSteffen Maier <maier@linux.ibm.com>
Reviewed-by: NJens Remus <jremus@linux.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 6419f818ababebc1116fb2d0e220bd4fe835d0e3 ]

For the error path in wilc_wlan_initialize(), the resources are not
cleanup in the correct order. Reverted the previous changes and use the
correct order to free during error condition.

Fixes: b46d6882 ("staging: wilc1000: remove COMPLEMENT_BOOT")
Cc: <stable@vger.kernel.org>
Signed-off-by: NAjay Singh <ajay.kathat@microchip.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 5676234f20fef02f6ca9bd66c63a8860fce62645 ]

WRITE SAME corrupts data on the block device behind iblock if the command
is emulated. The emulation code issues (M - 1) * N times more bios than
requested, where M is the number of 512 blocks per real block size and N is
the NUMBER OF LOGICAL BLOCKS specified in WRITE SAME command. So, for a
device with 4k blocks, 7 * N more LBAs gets written after the requested
range.

The issue happens because the number of 512 byte sectors to be written is
decreased one by one while the real bios are typically from 1 to 8 512 byte
sectors per bio.

Fixes: c66ac9db ("[SCSI] target: Add LIO target core v4.0.0-rc6")
Cc: <stable@vger.kernel.org>
Signed-off-by: NRoman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 80b045b385cfef10939c913fbfeb19ce5491c1f2 ]

Instead of duplicating the SECTOR_SHIFT definition from <linux/blkdev.h>,
use it. This patch does not change any functionality.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>