The sink rate read from supported link rate table is in KHz as per spec
while in drm, the saved clock is in deca-KHz. So divide the link rate by
10 before storing.

Reading of rates was added by:
commit fc0f8e25 ("drm/i915/skl: Read sink supported rates from edp
panel")

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NSonika Jindal <sonika.jindal@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

The eDP port A register on PCH split platforms has a slightly different
register layout from the other ports, with bit 6 being either alternate
scrambler reset or reserved, depending on the generation. Our
misinterpretation of the bit as audio has lead to warning.

Fix this by not enabling audio on port A, since none of our platforms
support audio on port A anyway.

v2: DDI doesn't have audio on port A either (Sivakumar Thulasimani)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89958Reported-and-tested-by: NChris Bainbridge <chris.bainbridge@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Connector states were being allocated in intel_setup_outputs() in loop
over all connectors. That meant hot-added connectors would have a NULL
state. Since the change to use a struct drm_atomic_state for the legacy
modeset, connector states are necessary for the i915 driver to function
properly, so that would lead to oopses.

Broken by

commit 944b0c76
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date:   Fri Mar 20 16:18:07 2015 +0200

    drm/i915: Copy the staged connector config to the legacy atomic state

v2: Fix test for intel_connector_init() success in lvds and sdvo (PRTS)
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reported-and-tested-by: NNicolas Kalkhof <nkalkhof@web.de>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Latest version of the "CHV DPIO programming notes" no longer requires writes
to TX DW 11 to fix a +2UI interpair skew issue. The current code from
April 2014 was actually causing additional skew issues between all
TMDS pairs.

ver2: added same treatment to intel_dp.c based on Ville's testing.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NClint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

It's not needed since the worker rechecks that it didn't race. We only
need to cancel synchronously after disabling drrs to make sure the
worker really is gone (e.g. for driver unload). But for normal
operation the stall is just wasted time.
Reported-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

We must acquire the mutex before we can check drrs.dp, otherwise
someone might sneak in with a modeset, clear the pointer after we've
checked it and then the code will Oops.

This issue has been introduced in

commit a93fad0f
Author: Vandana Kannan <vandana.kannan@intel.com>
Date:   Sat Jan 10 02:25:59 2015 +0530

    drm/i915: DRRS calls based on frontbuffer

v2: Don't blow up on uninitialized mutex and work item by checking
whether DRRS is support or not first. Also unconditionally initialize
the mutex/work item to avoid future trouble.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Vandana Kannan <vandana.kannan@intel.com>
Cc: stable@vger.kernel.org (4.0+ only)
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

The function intel_dp_set_drrs_state() would decide which pipe to
downclock based on the staged config for the given connector. However,
the result of that function is immediate, and it uses input values from
crtc->config, so it should be looking at the current crtc instead.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Move towards atomic by using the legacy modeset's drm_atomic_state
instead.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So that we can add connector states to the drm_atomic_state used in the
legacy modeset.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As part of allocation of the drm_i915_private variable, drrs capability
enum is initialized to DRRS_NOT_SUPPORTED. Hence need not initialize at
each connector init.

Moreover initializing this enum at connector init will reset
the successful DRRS initialization of previous connector, as we have
the DRRS support for only one panel at a time.
Signed-off-by: NRamalingam C <ramalingam.c@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

AUX addresses are 20 bits long. Send out the entire address instead of
just the low 16 bits.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Allow for a larger receive data size, and check if the receiver returned
the number of bytes written. Without this, we've basically skipped all
the unwritten bytes for short writes.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To keep things clear rename the intel_dp->supported_rates[] to
intel_dp->sink_rates[], and rename the supported_rates[] name we used
elsewhere for the intersection of source and sink rates to
common_rates[].

Cc: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

TODO: Is there an actually nice way to print an array of ints?
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

"P1273_DPLL_Programming Spreadsheet.xlsm" lists a boatload of
frequencies for eDP. Try to use them all.

For now I've decided not to add hardcoded DPLL dividers for these cases
since chv_find_best_dpll() works just fine.

I've not actually tested any of these since I don't have an eDP 1.4 panel.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Complain loudly if we ever attempt to overflow the the supported_rates[]
array. This should never happen since the sink_rates[] array will always
be smaller or of equal size. But should someone change that we want to
catch it without scribblign over the stack.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that intel_dp_max_link_bw() no longer considers the source
restrictions we may try to enable MST with 5.4GHz even when the source
doesn't support it. To fix that switch the code over to handle the link
rate in the same way as the SST code handles it.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Drop the gen9 checks from the code and issue DP_LINK_RATE_SET whenever
the sink reports to support it.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Consider the link rates reported by the sink via
DP_SUPPORTED_LINK_RATES when checking modes against the max link
rate.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

intel_dp_compute_config() only really needs to know the rates supported
by both source and sink, so hide the raw source and sink arrays from it.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Remove the sink vs. source limit mess from intel_dp_max_link_bw() and
just move the source restriction checks to intel_dp_source_rates().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
[danvet: Resolve conflict with WaDisableHBR2:skl patch.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that both source and sink rates are always filled in there's no need
for any special cases in intel_supported_rates().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Once we've read the rates from the sink we don't have to mess with them,
so the caller can just look at the stored rates without doing extra
copies. If the sink doesn't support the new link rate stuff, we just
point the caller at the default_rates[] array.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The source rates don't change, so we can just point the caller at the
const arrays.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Reviewed-by: NTodd Previte <tprevite@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

No point in converting from hardware format every single time, just
store the rates in the final format under intel_dp.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Reviewed-by: NTodd Previte <tprevite@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

No point in using uint32_t here, just plain old int will do.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Reviewed-by: NTodd Previte <tprevite@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Use the recently introduced INTEL_REVID() and SKL_REVID defines
    (Nick Hoath)
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89554Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Making the link_clock half in switch inline with the DPLL_CTRL1_* macros
(Ville)
Signed-off-by: NSonika Jindal <sonika.jindal@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

eDp 1.4 supports custom frequencies.
Skylake supports following intermediate frequencies : 3.24 GHz, 2.16 GHz and
4.32 GHz along with usual LBR, HBR and HBR2 frequencies.
Read sink supported frequencies and get common frequencies from sink and
source and use these for link training.

v2: Rebased, removed calculation of min_clock since for edp it is taken as
max_clock (as per comment).
v3: Keeping single array for link rates (Satheesh)
v4: Setting LINK_BW_SET to 0 when setting LINK_RATE_SET (Satheesh)
v5: Some minor nits (Ville)
v6: Keeping separate arrays for source and sink rates (Ville)
v7: Remove redundant setting of DP_LINK_BW_SET to 0 (Ville)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Using DP_SUPPORTED_LINK_RATES macro for supported_rates array (Satheesh).
v3: Reading dpcd's supported link rates tables based upon edp version in the
same patch.
v4: Move version check under is_edp (Satheesh)
v5: Using le16 for rates, some naming, and removing nested if block (Ville)
v6: Correctly using DP_MAX_SUPPORTED_RATES and removing DP_SUPPORTED_LINK_RATES
(Ville)
v7: Incorrectly removed DP_SUPPORTED_LINK_RATES in v6, re-adding it
v8: Checking return value of intel_dp_dpcd_read_wake() (Ville)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In invalidate and flush functions of eDP DRRS, if deferred downclock
work starts execution at a time window between acquiring the drrs
mutex and cancellation of the deferred work
(intel_edp_drrs_downclock_work), then deferred work will find
drrs mutex locked and wait for the same.

Meanwhile the function that acquired mutex drrs invalidate/flush will
wait for the completion of the deferred work before releasing the mutex.
Thats a deadlock.

To avoid such deadlock scenario, this change cancels the deferred work
before acquiring the mutex at invalidate and flush functions.
Signed-off-by: NRamalingam C <ramalingam.c@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Based upon vbt's vswing preemph settings value select the appropriate
translations for edp.

v2: Incorporating bspec changes for vswing and preemph levels, adding edp
translation table. Removed HSW from selection 9 which is specific to skl and
correcting the returning of level2 from max pre emph (Damien)

v3: Rebasing on top of renaming patches. Adding level(3,0) since level(2,2) as
mentioned in bspec is invalid as per edp spec. Also changed the determining of
size of the table selected (Satheesh).

v4: Adding level 3 in max voltage selection if low vswing is selected (Satheesh)

v5: Add a comment stating that skl_ddi_translations_edp is for eDP 1.4
    low vswing panels.

v6: Updating recommended DDI translation table for edp 1.4

Reviewed-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v4)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> (v6)
Signed-off-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When Downclock mode is not found, the same info is added to the
corresponding debug log.
Signed-off-by: NRamalingam C <ramalingam.c@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Adding an overview of DRRS in general and the implementation for eDP DRRS.
Also, describing the functions related to eDP DRRS.
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch enables eDP DRRS for CHV by adding the
required IS_CHERRYVIEW() checks.
CHV uses the same register bit as VLV.

[Vandana]: Since CHV has 2 sets of M_N registers, it will follow the same code
path as gen < 8. Added CHV check in dp_set_m_n()

[Ram]: Rebased on top of previous patch modifications
Signed-off-by: NDurgadoss R <durgadoss.r@intel.com>
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Signed-off-by: NRamalingam C <ramalingam.c@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Definition of VLV RR switch bit and corresponding toggling in
set_drrs function.
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For Broadwell, there is one instance of Transcoder MN values per transcoder.
For dynamic switching between multiple refreshr rates, M/N values may be
reprogrammed on the fly. Link N programming triggers update of all data and
link M & N registers and the new M/N values will be used in the next frame
that is output.

V2: [By Ram]: intel_dp_set_m_n() is rewritten to accommodate
	gen >= 8 [Rodrigo]
V3: Coding style correction [Ram]
V4: [By Ram] intel_dp_set_m_n modifications are moved into a
	separate patch, retaining only DRRS related changes here [Rodrigo]
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Signed-off-by: NPradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: NRamalingam C <ramalingam.c@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This was introduced in:

  commit 0bc12bcb
  Author: Rodrigo Vivi <rodrigo.vivi@intel.com>
  Date:   Fri Nov 14 08:52:28 2014 -0800

      drm/i915: Introduce intel_psr.c

But the unpack function is unused at this date.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This function is only used in intel_dp.c since:

  commit 0e32b39c
  Author: Dave Airlie <airlied@redhat.com>
  Date:   Fri May 2 14:02:48 2014 +1000

      drm/i915: add DP 1.2 MST support (v0.7)
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Return IRQ_HANDLED from intel_dp_hpd_pulse() to properly
ignore the long HPD pulse on eDP to avoid the never ending
VDD off->HPD->VDD on->VDD off->HPD... cycle.

This fixes a regression intoduced by
 commit b2c5c181
 Author: Daniel Vetter <daniel.vetter@ffwll.ch>
 Date:   Fri Jan 23 06:00:31 2015 +0100

    drm/i915: Use symbolic irqreturn for ->hpd_pulse

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>