It's expected behaviour for the CODEC header to provide them but the
WM8350 doesn't due to having all the registers together under drivers/mfd.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

There is only one LRCLK pin on each interface.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The S3C64xx IIS code had a number of problems with device registration.
The hardware has two IIS ports of which the driver supported only one
at once via a single exported DAI, attempting to identify the DAI to
use based on the dev->id of the ASoC platform device.  As well as
limiting the driver to only supporting one IIS port at once this also
meant that the ID of the soc-audio device (or in future the card device)
had to match the IIS ID.

Fix both problems by converting the driver to register the DAIs based on
probing of platform devices registered by the arch/arm code, using those
platform devices to interact with the clock API.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add a macro for double controls with special callback functions.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds support for the four channel TDM mode
on Beagle board.

Depending on the channel count, the interface needs to be
configured differently (I2S for stereo DSP_A for four channels)
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Support for 4 channel TDM (SND_SOC_DAIFMT_DSP_A) for twl4030
codec.
The channel allocations are:
Playback:
TDM         i2s   TWL RX
Channel 1   Left  SDRL2
Channel 3   Right SDRR2
Channel 2   --    SDRL1
Channel 4   --    SDRR1

Capture:
TDM         i2s   TWL TX
Channel 1   Left  TXL1
Channel 3   Right TXR1
Channel 2   --    TXL2
Channel 4   --    TXR2
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add 4 channel support to omap-mcbsp.
This mode is going to be used by the twl4030 codec, when it
is configured in Option1 mode.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It relies on EXPORT_SYMBOL_GPL() symbols.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The original idea came from pHilipp, and this makes the code looks
more consistent.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The SSP DMA parameters can actually be easily generated at run-time since
they are almost similar except for the FIFO width and direction. Another
benefit is the re-use of information from 'struct ssp_device', like SSDR
physical FIFO address and DRCMR register index for both directions.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: NpHilipp Zabel <philipp.zabel@gmail.com>

Add DAPMs for VDL(Voice Down Link) path. To support VDL path, we have
to change DAPMs of outputs(Earpiece, PreDrive Left/Right, Headset
Left/Right, Carkit Left/Right) from mux to mixer.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is now handled by symmetric_rates.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Save a little extra power by enabling the DC servo offset correction
for the output channels only when the relevant channels are enabled.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Modify the default startup sequence in the chip to set the DC servo
dither level for optimal performance.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

CLK_DSP provides a master clock for the DAC and ADC related functionality
on the device.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Many modern CODECs have shared resources on chip which must be enabled
for portions of the chip to work but which can be disabled at other times
in order to achieve power savings. Examples of such resources include
power supplies and some internal clocks.

Since these widgets are dependencies for the audio path but do not carry
audio signals they require slightly different handling to most widgets -
they do not contribute to the audio path and so should not be counted as
either inputs or outputs during path walks.

Cases where one supply provides a supply for another will require
additional work. There is also room for more optimisation of the graph
walking to avoid repeated checks for the same thing.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add checking in hw_params and prepare to detect bufferless pcms(i.e. BT
<--> codec).
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The driver is out of sync with the core functions it is using.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Rather than having switch statements at point of use make the DAPM
power check a member of the widget structure and set it when we
instantiate the widget.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This also switches us to using a switch statement for the widget type
in dapm_power_widget().
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This will form a basis for further power check refactoring: the overall
goal of these changes is to allow us to check power separately to
applying it, allowing improvements in the power sequencing algorithms.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add Voice DAI to support the PCM voice interface of the twl4030 codec.

The PCM voice interface can be used with 8-kHz(voice narrowband) or
16-kHz(voice wideband) sampling rates, and 16bits, and mono RX and mono
TX or stereo TX.

The PCM voice interface has two modes
 - PCM mode1 : This uses the normal FS polarity and the rising edge of
               the clock signal.
 - PCM mode2 : This uses the FS polarity inverted and the falling edge
               of the clock signal.

If the system master clock is not 26MHz or the twl4030 codec mode is not
option2, the voice PCM interface is not available.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

I notice that the fixes were merged, minus one:

sound/soc/codecs/wm9705.c: At top level:
sound/soc/codecs/wm9705.c:445: warning: initialization from incompatible pointer type

so you might find this trivial patch useful.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The original implementation of the constraints were good against sane
applications.
If the opening sequence is:
stream1_open, stream1_hw_params, stream2_open, stream2_hw_params -> the
constraints are set correctly for stream2.

But if the sequence is:
stream1_open, stream2_open, stream2_hw_params, stream1_hw_params -> than stream2
would receive constraint rate = 0, sample_bits = 0, since the stream1 has not
yet called hw_params...

The command to trigger this event:
gst-launch-0.10 alsasrc device=hw:0 ! alsasink device=hw:0 sync=false

This patch does some 'black magic' in order to always set the correct
constraints and sets it only when it is needed for the other stream.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

My email address is going to expire soon so update it. Adding also
Peter Ujfalusi <peter.ujfalusi@nokia.com> as a second contact to OMAP core
drivers since I won't have anymore access to non-public OMAP documentation
in the future and Peter is working with these drivers as well.
Signed-off-by: NJarkko Nikula <jarkko.nikula@nokia.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Those macros are just screwed as soon as CONFIG_PXA25x is enabled.

This patch
- changes ssp_set_scr to take an ssp_dev pointer instead of ssp_device
- adds a corresponding ssp_get_scr function.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

DSP_A mode is similar to the DSP_B, but the MSB is delayed with
one bclk (appears after the FS pulse and not under it).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NJarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use single-phase mode for the DSP mode and keep the dual phase
mode for the I2S mode.

The mono (1 channel) mode already used single phase mode,
now it is more cleaner. There is no need to configure the
second phase, when the single phase is used.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NJarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Using inverted FS polarity in OSK5912 must be an error since TLV320AIC23
do not have support for inverted polarities. This is mostly due the hassle
with the DSP formats in OMAP McBSP DAI and inversion on OMAP side probably
just made this configuration working at some point.
Signed-off-by: NJarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: NArun KS <arunks@mistralsolutions.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The DSP format wasn't still correct in OMAP McBSP DAI even after the commit
bd25867a.

Thanks to Peter Ujfalusi <peter.ujfalusi@nokia.com> for noticing and being
part of the fix. Now the FS length definition is more clear by defining
it with  FWID(0).
Signed-off-by: NJarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>