Impact: on SGI UV platforms, fix boot crash

UV initialization is currently called too late to call alloc_bootmem_pages().
The current sequence is:

 start_kernel()
   mem_init()
     free_all_bootmem()           <--- discard of bootmem
   rest_init()
     kernel_init()
       smp_prepare_cpus()
       native_smp_prepare_cpus()
         uv_system_init()         <--- uses alloc_bootmem_pages()

It should be calling kmalloc().
Signed-off-by: NCliff Wickman <cpw@sgi.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: fix guest kernel boot crash on certain configs

Recent i686 2.6.27 kernels with a certain amount of memory (between
736 and 855MB) have a problem booting under a hypervisor that supports
batched mprotect (this includes the RHEL-5 Xen hypervisor as well as
any 3.3 or later Xen hypervisor).

The problem ends up being that xen_ptep_modify_prot_commit() is using
virt_to_machine to calculate which pfn to update.  However, this only
works for pages that are in the p2m list, and the pages coming from
change_pte_range() in mm/mprotect.c are kmap_atomic pages.  Because of
this, we can run into the situation where the lookup in the p2m table
returns an INVALID_MFN, which we then try to pass to the hypervisor,
which then (correctly) denies the request to a totally bogus pfn.

The right thing to do is to use arbitrary_virt_to_machine, so that we
can be sure we are modifying the right pfn.  This unfortunately
introduces a performance penalty because of a full page-table-walk,
but we can avoid that penalty for pages in the p2m list by checking if
virt_addr_valid is true, and if so, just doing the lookup in the p2m
table.

The attached patch implements this, and allows my 2.6.27 i686 based
guest with 768MB of memory to boot on a RHEL-5 hypervisor again.
Thanks to Jeremy for the suggestions about how to fix this particular
issue.
Signed-off-by: NChris Lalancette <clalance@redhat.com>
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Chris Lalancette <clalance@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

* 'for-linus' of git://neil.brown.name/md:
  md: allow extended partitions on md devices.
  md: use sysfs_notify_dirent to notify changes to md/dev-xxx/state
  md: use sysfs_notify_dirent to notify changes to md/array_state

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: psmouse - add support for Elantech touchpads
  Input: i8042 - add Blue FB5601 to noloop exception table

* 'for-linus' of git://git.o-hand.com/linux-mfd:
  mfd: Make WM8400 depend on I2C until SPI is submitted
  mfd: add missing Kconfig entry for da903x

* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb:
  uwb: build UWB before USB/WUSB

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: Add support for Sony Vaio VGX-TP1E
  HID: fix lock imbalance in hiddev
  HID: fix lock imbalance in hidraw
  HID: fix hidbus/appletouch device binding regression
  HID: add hid_type to general hid struct
  HID: quirk for OLED devices present in ASUS G50/G70/G71
  HID: Remove "default m" for Thrustmaster and Zeroplus
  HID: fix hidraw_exit section mismatch
  HID: add support for another Gyration remote control
  Revert "HID: Invert HWHEEL mappings for some Logitech mice"

Fix docbook fatal errors (file location changed):

docproc: lin2628-rc1/include/asm-x86/io_32.h: No such file or directory
make[1]: *** [Documentation/DocBook/deviceiobook.xml] Error 1

docproc: lin2628-rc1/include/asm-x86/atomic_32.h: No such file or directory
make[1]: *** [Documentation/DocBook/kernel-api.xml] Error 1

docproc: lin2628-rc1/include/asm-x86/mca_dma.h: No such file or directory
make[1]: *** [Documentation/DocBook/mcabook.xml] Error 1
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow macros that are annotated with kernel-doc to contain whitespace
between the '#' and "define".  It's valid and being used, so allow it.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  leds-hp-disk: fix build warning
  ACPI: Oops in ACPI with git latest
  ACPI suspend: build fix for ACPI_SLEEP=n && XEN_SAVE_RESTORE=y.
  toshiba_acpi: always call input_sync() after input_report_switch()
  ACPI: Always report a sync event after a lid state change
  ACPI: cpufreq, processor: fix compile error in drivers/acpi/processor_perflib.c
  i7300_idle: Fix compile warning CONFIG_I7300_IDLE_IOAT_CHANNEL not defined
  i7300_idle: Cleanup based review comments
  i7300_idle: Disable ioat channel only on platforms where ile driver can load

.. fix all the worst problems in -rc1

If CONFIG_AMIGA_BUILTIN_SERIAL=m, I get the following warnings:

| drivers/char/amiserial.c: At top level:
| drivers/char/amiserial.c:2138: warning: data definition has no type or storage class
| drivers/char/amiserial.c:2138: warning: type defaults to 'int' in declaration of 'console_initcall'
| drivers/char/amiserial.c:2138: warning: parameter names (without types) in function declaration
| drivers/char/amiserial.c:2134: warning: 'amiserial_console_init' defined but not used

because console_initcall() is not defined (nor really sensible) in the
modular case.

So disable serial console support if the driver is modular.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In commit f337b9c5 ("epoll: drop
unnecessary test") Thomas found that there is an unnecessary (always
true) test in ep_send_events().  The callback never inserts into
->rdllink while the send loop is performed, and also does the
~EP_PRIVATE_BITS test.  Given we're holding the mutex during this time,
the conditions tested inside the loop are always true.

HOWEVER.

The test "!ep_is_linked(&epi->rdllink)" wasn't there because we insert
into ->rdllink, but because the send-events loop might terminate before
the whole list is scanned (-EFAULT).

In such cases, when the loop terminates early, and when a (leftover)
file received an event while we're performing the lockless loop, we need
such test to avoid to double insert the epoll items.  The list_splice()
done a few steps below, will correctly re-insert the ones that were left
on "txlist".

This should fix the kenrel.org bugzilla entry 11831.
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some userland apps seem to pass in a "0" for the seconds, and several
seconds worth of usecs to select().  The old kernels accepted this just
fine, so the new kernels must too.

However, due to the upscaling of the microseconds to nanoseconds we had
some cases where we got math overflow, and depending on the GCC version
(due to inlining decisions) that actually resulted in an -EINVAL return.

This patch fixes this by adding the excess microseconds to the seconds
field.

Also with thanks to Marcin Slusarz for spotting some implementation bugs
in the diagnostics patches.
Reported-by: NCarlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The default for the regulatory compatibility option is wrong;
if you picked the default you ended up with a non-functional wifi
system (at least I did on Fedora 9 with iwl4965).
I don't think even the October 2008 releases of the various distros
has the new userland so clearly the default is wrong, and also
we can't just go about deleting this in 2.6.29...

Change the default to "y" and also adjust the config text a little to
reflect this.

This patch fixes regression #11859

With thanks to Johannes Berg for the diagnostics
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

/scratch/sfr/next/kernel/cgroup.c: In function 'cgroup_tasks_start':
/scratch/sfr/next/kernel/cgroup.c:2107: warning: unused variable 'i'

Introduced in commit cc31edce "cgroups:
convert tasks file to use a seq_file with shared pid array".
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  hwmon: (abituguru3) enable DMI probing feature on AW9D-MAX
  hwmon: (abituguru3) Cosmetic whitespace fixes
  hwmon: (adt7473) Fix voltage conversion routines
  hwmon: (lm90) Add support for the LM99 16 degree offset
  hwmon: (lm90) Fix handling of hysteresis value
  hwmon-vid: Add support for AMD family 10h CPUs
  hwmon: (w83781d) Fix linking when built-in

This reverts commit 7bf6bf48.

The code has both a short existence and an increasing track of failures
despite some work to amend it for -rc1.  It is not just a matter of
reading the eeprom: sometimes the eeprom is read correctly, then the mac
address is not written correctly back into the mac registers.

Some chipsets seem to work reliably but it is not clear at this point if
the code can simply be made to work on a per-chipset basis and post -rc1
is not the place where I want to experiment these things.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

a) semicolon before the function body is a bad idea
b) it's const struct foo, not struct const foo
c) incidentally, it's ecard_remove_driver(), not ecard_unregister_driver()
d) compiling is occasionally useful.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If you use KCONFIG_ALLCONFIG (even with empty file) you get broken
allmodconfig/allyesconfig; CONFIG_MODULES gets turned off, with obvious
massive fallout.

Breakage had been introduced when conf_set_all_new_symbols() got used
for allmodconfig et.al.

What happens is that sym_calc_value(modules_sym) done in
conf_read_simple() sets SYMBOL_VALID on both modules_sym and MODULES.
When we get to conf_set_all_new_symbols(), we set sym->def[S_DEF_USER]
on everything, but it has no effect on sym->curr for the symbols that
already have SYMBOL_VALID - these are stuck.

Solution: use sym_clear_all_valid() in there.  Note that it makes
reevaluation of modules_sym redundant - sym_clear_all_valid() will do
that itself.

[ Fixes http://bugzilla.kernel.org/show_bug.cgi?id=11512, says Alexey ]
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Switch the AW9D-MAX over from port probing to the preferred DMI
probe method.
Signed-off-by: NAlistair John Strachan <alistair@devzero.co.uk>
Tested-by: NJustin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

As the probable result of zealous copy/pasting, many supported boards
contain sensor names with trailing whitespace. Though this is not a
huge problem, it is inconsistent with other sensor names, and with
other similar hwmon drivers.

Additionally, the DMI nag message added in 2.6.27 was missing a
space between two sentence fragments -- might as well clean that up
too.

Doesn't alter any kernel text, just data.
Signed-off-by: NAlistair John Strachan <alistair@devzero.co.uk>
Reported-by: NJustin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Fix voltage conversion routines. Based on an earlier patch from
Paulius Zaleckas.

According to the datasheet voltage is scaled with resistors and
value 192 is nominal voltage. 0 is 0V.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Darrick J. Wong <djwong@us.ibm.com>

The LM99 differs from the LM86, LM89 and LM90 in that it reports
remote temperatures (temp2) 16 degrees lower than they really are. So
far we have been cheating and handled this in userspace but it really
should be handled by the driver directly.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>

There are several problems in the way the hysteresis value is handled
by the lm90 driver:

* In show_temphyst(), specific handling of the MAX6646 is missing, so
  the hysteresis is reported incorrectly if the critical temperature
  is over 127 degrees C.
* In set_temphyst(), the new hysteresis register value is written to
  the chip but data->temp_hyst isn't updated accordingly, so there is
  a short period of time (up to 2 seconds) where the old hystereris
  value will be returned while the new one is already active.
* In set_temphyst(), the critical temperature which is used as a base
  to compute the value of the hysteresis register lacks
  device-specific handling. As a result, the value of the hysteresis
  register might be incorrect for the ADT7461 and MAX6646 chips.

Fix these 3 bugs.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Nate Case <ncase@xes-inc.com>

The AMD family 10h CPUs use the same VID decoding table as the family
0Fh CPUs.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>

When w83781d is built-in, the final links fails with the following vague error
message:

`.exit.text' referenced in section `.init.text' of drivers/built-in.o: defined
in discarded section `.exit.text' of drivers/built-in.o

w83781d_isa_unregister() cannot be marked __exit, as it's also called from
sensors_w83781d_init(), which is marked __init.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: Fix duplicate entries returned from getdents() system call
  ext3: Fix duplicate entries returned from getdents() system call

This reverts commit a802dd0e by moving
the call to init_workqueues() back where it belongs - after SMP has been
initialized.

It also moves stop_machine_init() - which needs workqueues - to a later
phase using a core_initcall() instead of early_initcall().  That should
satisfy all ordering requirements, and was apparently the reason why
init_workqueues() was moved to be too early.

Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a regression caused by commit d0156417, "ext4: fix ext4_dx_readdir
hash collision handling", where deleting files in a large directory
(requiring more than one getdents system call), results in some
filenames being returned twice.  This was caused by a failure to
update info->curr_hash and info->curr_minor_hash, so that if the
directory had gotten modified since the last getdents() system call
(as would be the case if the user is running "rm -r" or "git clean"),
a directory entry would get returned twice to the userspace.
Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>

This patch fixes the bug reported by Markus Trippelsdorf at:
http://bugzilla.kernel.org/show_bug.cgi?id=11844Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
Tested-by: NMarkus Trippelsdorf <markus@trippelsdorf.de>

Fix a regression caused by commit 6a897cf4, "ext3: fix ext3_dx_readdir
hash collision handling", where deleting files in a large directory
(requiring more than one getdents system call), results in some
filenames being returned twice.  This was caused by a failure to
update info->curr_hash and info->curr_minor_hash, so that if the
directory had gotten modified since the last getdents() system call
(as would be the case if the user is running "rm -r" or "git clean"),
a directory entry would get returned twice to the userspace.

This patch fixes the bug reported by Markus Trippelsdorf at:
http://bugzilla.kernel.org/show_bug.cgi?id=11844Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
Tested-by: NMarkus Trippelsdorf <markus@trippelsdorf.de>

drivers/leds/leds-hp-disk.c:59: warning: passing argument 4 of ‘acpi_evaluate_integer’ from incompatible pointer type
Signed-off-by: NLen Brown <len.brown@intel.com>

ACPI Warning (nseval-0168): Insufficient arguments - method [_OSC] needs 5, found 4 [20080926]
ACPI Warning (nspredef-0252): \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, expected 4 [20080926]
ACPI Error (nspredef-0163): \_SB_.PCI0._OSC: Missing expected return value [20080926]
BUG: unable to handle kernel NULL pointer dereference at 00000000
IP: [<c0237671>] acpi_run_osc+0xa1/0x170
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Tested-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NLen Brown <len.brown@intel.com>

Currently not always an EV_SYN event is reported to userland
after the EV_SW SW_LID event has been sent. This is easy to verify
by using “input-events” from input-utils and just closing and opening
the lid.
Signed-off-by: NGuillem Jover <guillem.jover@nokia.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

When trying to build 2.6.28-rc1 on ia64, make aborts with:

  CC      drivers/acpi/processor_perflib.o
  drivers/acpi/processor_perflib.c:41:28: error: asm/cpufeature.h: No such file or directory
  drivers/acpi/processor_perflib.c: In function ‘acpi_processor_get_performance_info’:
  drivers/acpi/processor_perflib.c:364: error: implicit declaration of function ‘boot_cpu_has’
  drivers/acpi/processor_perflib.c:364: error: ‘X86_FEATURE_EST’ undeclared (first use in this function)
  drivers/acpi/processor_perflib.c:364: error: (Each undeclared identifier is reported only once
  drivers/acpi/processor_perflib.c:364: error: for each function it appears in.)
  make[2]: *** [drivers/acpi/processor_perflib.o] Error 1
  make[1]: *** [drivers/acpi] Error 2
  make: *** [drivers] Error 2

this patch fix it.
Signed-off-by: NMiao Xie <miaox@cn.fujitsu.com>
Acked-by: NThomas Renninger <trenn@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

When I7300_idle driver is not configured, there is a compile time
warning about IDLE_IOAT_CHANNEL not defined. Fix it.
Reported-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Reported-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Cleanup of i7300 idle driver based on review comments from Randy Dunlap,
Andi Kleen and Len Brown.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>