Reimplement ata_acpi_cbl_80wire() using ata_acpi_gtm_xfermask() and
while at it relocate the function below ata_acpi_gtm_xfermask().

New ata_acpi_cbl_80wire() implementation takes @gtm, in both pata_via
and pata_amd, use the initial GTM value.  Both are trying to peek
initial BIOS configuration, so using initial caching value makes
sense.  This fixes ACPI part of cable detection in pata_amd which
previously always returned 0 because configuring PIO0 during reset
clears DMA configuration.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

libata-acpi is using separate timing tables for transfer modes
although libata-core has the complete ata_timing table.  Implement
ata_timing_cycle2mode() to look for matching mode given transfer type
and cycle duration and use it in libata-acpi and pata_acpi to replace
private timing tables.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_acpi_gtm_xfermask() as separated out from pacpi_discover_modes()
has various bugs.  Fix them.

* The wrong comparison operator is used when finding for matching
  cycle resulting totally bogus result.

* With the comparion operator fixed, boundary condtion handling is
  clumsy.

* Setting of any DMA mask bit set all bits in PIO mask.

* MWDMA and UDMA blocks are swapped.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Finding out matching transfer mode from ACPI GTM values is useful for
other purposes too.  Separate out the function and timing tables from
pata_acpi::pacpi_discover_modes().

Other than checking shared-configuration bit after doing
ata_acpi_gtm() in pacpi_discover_modes() which should be safe, this
patch doesn't introduce any behavior change.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Separate controller IDs into a separate enum as Jeff requested.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make pdc_atapi_pkt() use values from qc->tf instead of creating its
own.  This is to ease future ATAPI handling changes.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ATA_CBL_PATA_UNK indicates that the cable type can't be determined
from the host side and might be either 80c or 40c.  libata applies
drive or other generic limit in this case.  However, there are
controllers where both host and drive side detections are
misimplemented and the driver has to rely solely on private method -
peeking BIOS or ACPI configuration or using some other private
mechanism.

This patch adds ATA_CBL_PATA_IGN which tells libata to ignore the
cable type completely and just let the LLD determine the transfer mode
via host transfer mode masks and ->mode_filter().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Jeff says xfer_mask is unsigned long not unsigned int.  Convert all
xfermask fields and handling functions to deal with unsigned longs.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_id_to_dma_mode() isn't quite generic.  The function is basically
privately implemented ata_id_xfermask() combined with hardcoded mode
printing and configuration which are specific to ata_generic.

Kill the function and open code it in generic_set_mode() using generic
xfermode handling functions.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* s/ATA_BITS_(PIO|MWDMA|UDMA)/ATA_NR_\1_MODES/g

* Consistently use 0xff to indicate invalid transfer mode (0x00 is
  valid for PIO_SLOW).

* Make ata_xfer_mode2mask() return proper mode mask instead of just
  the highest bit.

* Sort ata_timing table in increasing xfermode order and update
  ata_timing_find_mode() accordingly.

This patch doesn't introduce any behavior change.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Export the following xfermode related functions.

* ata_pack_xfermask()
* ata_unpack_xfermask()
* ata_xfer_mask2mode()
* ata_xfer_mode2mask()
* ata_xfer_mode2shift()
* ata_mode_string()
* ata_id_xfermask()
* ata_timing_find_mode()

These functions will be used later by LLD updates.  While at it,
change unsigned short @speed to u8 @xfer_mode in
ata_timing_find_mode() for consistency.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Unindent loop body in generic_set_mode().  This is to ease future
change.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

It's very likely that the configured data transfer mode is the wrong
one if device fails data transfers right after initial data transfer
mode configuration (including NCQ on/off and xfermode).  libata EH
needs to speed down fast before upper layers give up on probing.

This patch implement fast speed down rules to handle such cases
better.  Error occured while data transfer hasn't been verified
trigger fast back-to-back speed down actions until data transfer
works.

This change will make cable mis-detection and other initial
configuration problems corrected before partition scanning code gives
up.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ATA_DFLAG_DUBIOUS_XFER is set whenever data transfer speed or method
changes and gets cleared when data transfer command succeeds in the
newly configured transfer mode.

This will be used to improve speed down logic.

Signed-off-by: Tejun Heo <htejun@gmail.com<
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Speed down rules were too conservative.  Adjust them a bit.

* More than 10 timeouts can't happen in 5 minutes as command timeout
  is 30secs.  Lower the limit for rule #1 to 6.

* 10 timeouts is too high for rule #3 too.  Lower it to 6.

* SATAPI can benefit from falling back to PIO too.  Allow SATAPI
  devices to fall back to PIO.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Clean up EH speed down implementation.

* is_io boolean variable is replaced eflags.  is_io is ATA_EFLAG_IS_IO.

* Error categories now have names.

* Better comments.

* Reorder 5min and 10min rules in ata_eh_speed_down_verdict()

* Use local variable @link to cache @dev->link in ata_eh_speed_down()

These changes are to improve readability and ease further changes.
This patch doesn't introduce any behavior change.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Move ata_set_mode() to libata-eh.c.  ata_set_mode() is surely an EH
action and will be more tightly coupled with the rest of error
handling.  Move it to libata-eh.c.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Factor out ata_eh_schedule_probe() from ata_eh_handle_dev_fail() and
ata_eh_recover().  This is to improve maintainability and make future
changes easier.

In the previous revision, ata_dev_enabled() test was accidentally
dropped while factoring out.  This problem was spotted by Bartlomiej.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Implement protocol tests - ata_is_atapi(), ata_is_nodata(),
ata_is_pio(), ata_is_dma(), ata_is_ncq() and ata_is_data() and use
them to replace is_atapi_taskfile() and hard coded protocol tests.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Area for DFLAGs which are cleared on INIT is full.  Extend it by 8
bits.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

For intel ones, ahci unconditionally OR'd 0xf to PCS.  This isn't
correct for the following cases.

* ich6/7m's which only implement P0 and P2 (0xf works fine tho)

* ich8/9's which have six ports and needs 0x3f to enable all ports

This patch updates PCS programming such that...

* port_map determined by ahci_save_initial_config() is OR'd instead of 0xf

* PCS is updated only if necessary (there are turned off enable bits)

port_map is determined from PORTS_IMPL PCI register which is
implemented as write or write-once register.  If the register isn't
programmed, ahci automatically generates it from number of ports,
which is good enough for PCS programming.  ICH6/7M are probably the
only ones where non-contiguous enable bits are necessary && PORTS_IMPL
isn't programmed properly but they're proven to work reliably with 0xf
anyway.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Lots of work needed to bring it up to scratch but it does work so you can
now use the card. That makes it at least useful, especially as the other
cardbus cards are usually INIC162x which aren't yet supported well.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Jeff said he preferred that the SFF tf_load followed the spec and we
documented that anyone who needed different overrode it, rather than it
using the ->check_status methods. No driver relies on the current behaviour.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

I believe this version meets all Sergei's objections

Correct the logic for when we issue a set features for transfer mode

- If the device has IORDY and the controller has IORDY - set the mode
- If the device has IORDY and the controller does not - turn IORDY off
- If neither has IORDY do nothing
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ACPI spec (ver 3.0a, p289) requires IDE power on/off executes ACPI _PSx
methods. As recently most PATA drivers use libata, this patch adds _PSx
method support in libata. ACPI spec doesn't mention if SATA requires the
same _PSx method.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Acked-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Historically word 48 in the identify data was used to mean 32bit I/O
was supported for VLB IDE etc. ATA8 reassigns this word to the Trusted
Computing Group, where it is used for TCG features. This means that
an ATA8 TCG drive is going to trigger 32bit I/O on some systems which
will be funny.

Anyway we need to sort this out ready for ATA8 so:
- Reorder the ata.h header a bit so the ata_version function occurs early
  in it
- Make dword_io check the ATA version
- Add an ATA8 version checking TCG presence test

While we are at it the current drafts have a flaw where it may not be
possible to disable TCG features at boot (and opt out of the trusted
model) as TCG intends because it relies on presence of a different
optional feature (DCS). Handle this in software by refusing the TCG
commands if libata.allow_tpm is not set. (We must make it possible
as some environments such as proprietary VDR devices will doubtless
want to use it to lock up content)

Finally as with CPRM print a warning so that the user knows they may
not be able to full access and use the device.
Signed-off-by: NAlan Cox <alan@redhat.com>

Add Toshiba Satellite R20 and Tecra M6 to broken suspend list.  Matt
Piermarini reported and provided the M6 patch.  This is from OSDL bug 7780.
Signed-off-by: NPeter Schwenke <peter@bluetoad.com.au>
Cc: Matt Piermarini <mattpiermarini@yahoo.com>
Acked-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When we set the MFGPT timer tick, there is a chance that we'll
immediately assert an event.  If for some reason the IRQ routing
for this clock has been setup for some other purpose, then we
could end up firing an interrupt into the SMM handler or worse.

This rearranges the timer tick init function to initalize the handler
before we set up the MFGPT clock to make sure that even if we get
an event, it will go to the handler.

Furthermore, in the handler we need to make sure that we clear the
event, even if the timer isn't running.
Signed-off-by: NJordan Crouse <jordan.crouse@amd.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NIngo Molnar <mingo@elte.hu>
Tested-by: NArnd Hannemann <hannemann@i4.informatik.rwth-aachen.de>

Fix typo in arch/powerpc/boot/flatdevtree_env.h.
There is no Documentation/networking/ixgbe.txt.

README.cycladesZ is now in Documentation/.
wavelan.p.h is now in drivers/net/wireless/.
HFS.txt is now Documentation/filesystems/hfs.txt.
OSS-files are now in sound/oss/.
Signed-off-by: NJohann Felix Soden <johfel@users.sourceforge.net>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
  hwmon: (it87) request only Environment Controller ports

* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
  Revert "x86: fix NMI watchdog & 'stopped time' problem"

* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
  sched: group scheduler, set uid share fix

rcu_online_cpu() should be __cpuinit instead of __devinit.

WARNING: vmlinux.o(.text+0x4b6d5): Section mismatch: reference to .init.text: (between 'rcu_cpu_notify' and 'wakeme_after_rcu')
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: NIngo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The extra rom[0] check is flagging valid temperatures as invalid when
there is already a CRC data transmission check.

w1_therm_read_bin()
	if (rom[8] == crc && rom[0])
		verdict = 1;

Requiring rom[0] to be non-zero will flag as invalid temperature
conversions when the low byte is zero, specifically the temperatures 0C,
16C, 32C, 48C, -16C, -32C, and -48C.

The CRC check is produced on the device for the previous 8 bytes and is
required to ensure the data integrity in transmission.  I don't see why the
extra check for rom[0] being non-zero is in there.  Evgeniy Polyakov didn't
know either.  Just for a check I unplugged the sensor, executed a
temperature conversion, and read the results.  The read was all ff's, which
also failed the CRC, so it doesn't need to protect against a disconnected
sensor.

I have more extensive patches in the work, but these two trivial ones will
do for today.  I would like to hear from people who use the ds2490 USB to
one wire dongle.  1 if you would be willing to test the patches as I
currently only have the one sensor on a short parisite powered wire, 2 if
there is any cheap sources for the ds2490.
Signed-off-by: NDavid Fries <david@fries.net>
Acked-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Correct the decoding of negative C temperatures.  The code did a binary OR
of two bytes to make a 16 bit value, but assignd it to an integer.  This
caused the value to not be sign extended and to loose that it was a
negative number in the assignment.

Before the patch (in my freezer),
	w1_slave
	ed fe 4b 46 7f ff 03 10 e4 : crc=e4 YES
	ed fe 4b 46 7f ff 03 10 e4 t=4078
With the patch,
	e3 fe 4b 46 7f ff 0d 10 81 : crc=81 YES
	e3 fe 4b 46 7f ff 0d 10 81 t=-17
Signed-off-by: NDavid Fries <david@fries.net>
Acked-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The IT8705F and related parts are Super I/O controllers that contain
many separate devices.

Some BIOSes describe IT8705F I/O port usage under a motherboard device
(PNP0C02) with overlapping regions, e.g., 0x290-0x29f and 0x290-0x294.

The it87 driver supports only the Environment Controller, which requires
only two ISA ports, but it used to request an eight-port range.  If that
range exceeds a range reported by the BIOS, as 0x290-0x297 would, the
request fails, and the it87 driver cannot claim the device.

This patch makes the it87 driver request only the two ports used for the
Environment Controller device.

Systems where this problem has been reported:
    Gigabyte GA-K8N Ultra 9
    Gigabyte M56S-S3
    Gigabyte GA-965G-DS3

Kernel bug reports:
    http://bugzilla.kernel.org/show_bug.cgi?id=9514
    http://lkml.org/lkml/2007/12/4/466

Related change:
    http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=a7839e960675b549f06209d18283d5cee2ce9261

    The patch above increases the number of PNP port resources we support.
    Prior to this patch, we ignored some port resources, which masked the
    it87 problem.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

setting cpu share to 1 causes hangs, as reported in:

    http://bugzilla.kernel.org/show_bug.cgi?id=9779

as the default share is 1024, the values of 0 and 1 can indeed
cause problems. Limit it to 2 or higher values.

These values can only be set by the root user - but still it
makes sense to protect against nonsensical values.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This reverts commit d4d25dec.

It tried to fix long standing bugzilla entries, but the solution was
reported to break other systems. The reporter of

http://bugzilla.kernel.org/show_bug.cgi?id=9791

tracked it down to this commit and confirmed that reverting the patch
restores the correct behaviour. It's too late in the release cycle to
find a better solution than reverting the commit to avoid regressions.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NIngo Molnar <mingo@elte.hu>