[bsp/nrf5x] add the bsp ble_nano_33

bsp/nrf5x/libraries/drivers/drv_uart.c

@@ -6,6 +6,7 @@
  * Change Logs:
  * Date           Author       Notes
  * 2020-04-28     xckhmf       Modify for <nrfx>
+ * 2021-06-26     supperthomas fix rt_hw_uart_init
  *
  */
 #include <rtdevice.h>
@@ -236,7 +237,7 @@ static struct rt_uart_ops _uart_ops = {
     _uart_getc
 };
 
-void rt_hw_uart_init(void)
+int rt_hw_uart_init(void)
 {
     struct serial_configure config = RT_SERIAL_CONFIG_DEFAULT;
 
@@ -249,5 +250,5 @@ void rt_hw_uart_init(void)
 #endif  /* BSP_USING_UART0 */
 
 }
-
+INIT_BOARD_EXPORT(rt_hw_uart_init);
 #endif /* BSP_USING_UART */

bsp/nrf5x/libraries/drivers/drv_uart.h

@@ -13,7 +13,6 @@
 
 // #define USE_UART0_1         0
 
-void rt_hw_uart_init(void);
 
 #endif
 

bsp/nrf5x/nrf52840/.config

@@ -3,6 +3,57 @@
 # RT-Thread Configuration
 #
 
+#
+# Hardware Drivers Config
+#
+CONFIG_SOC_NRF52840=y
+CONFIG_SOC_NORDIC=y
+CONFIG_BSP_BOARD_PCA_10056=y
+# CONFIG_BSP_BOARD_ARDUINO_NANO_33_BLE is not set
+
+#
+# Onboard Peripheral Drivers
+#
+CONFIG_BSP_USING_JLINK_TO_USART=y
+CONFIG_RT_BSP_LED_PIN=13
+# CONFIG_BSP_USING_QSPI_FLASH is not set
+
+#
+# On-chip Peripheral Drivers
+#
+CONFIG_BSP_USING_GPIO=y
+CONFIG_BSP_USING_UART=y
+CONFIG_NRFX_USING_UART=y
+# CONFIG_NRFX_USING_UARTE is not set
+CONFIG_BSP_USING_UART0=y
+CONFIG_BSP_UART0_RX_PIN=8
+CONFIG_BSP_UART0_TX_PIN=6
+# CONFIG_BSP_USING_SAADC is not set
+# CONFIG_BSP_USING_I2C is not set
+# CONFIG_BSP_USING_SPI is not set
+# CONFIG_BSP_USING_PWM is not set
+# CONFIG_BSP_USING_WDT is not set
+# CONFIG_BSP_USING_ONCHIP_RTC is not set
+# CONFIG_BSP_USING_ON_CHIP_FLASH is not set
+
+#
+# MCU flash config
+#
+CONFIG_MCU_FLASH_START_ADDRESS=0x00000000
+CONFIG_MCU_FLASH_SIZE_KB=1024
+CONFIG_MCU_SRAM_START_ADDRESS=0x20000000
+CONFIG_MCU_SRAM_SIZE_KB=256
+CONFIG_MCU_FLASH_PAGE_SIZE=0x1000
+CONFIG_BLE_STACK_USING_NULL=y
+# CONFIG_BSP_USING_SOFTDEVICE is not set
+# CONFIG_BSP_USING_NIMBLE is not set
+CONFIG_NRFX_CLOCK_ENABLED=1
+CONFIG_NRFX_CLOCK_DEFAULT_CONFIG_IRQ_PRIORITY=7
+CONFIG_NRFX_CLOCK_CONFIG_LF_SRC=1
+CONFIG_NRFX_UART_ENABLED=1
+CONFIG_NRFX_UART0_ENABLED=1
+CONFIG_NRFX_GPIOTE_ENABLED=1
+
 #
 # RT-Thread Kernel
 #
@@ -541,52 +592,3 @@ CONFIG_PKG_NRFX_VER="latest"
 # CONFIG_PKG_USING_STATE_MACHINE is not set
 # CONFIG_PKG_USING_MCURSES is not set
 # CONFIG_PKG_USING_COWSAY is not set
-
-#
-# Hardware Drivers Config
-#
-CONFIG_SOC_NRF52840=y
-CONFIG_SOC_NORDIC=y
-CONFIG_BSP_BOARD_PCA_10056=y
-
-#
-# Onboard Peripheral Drivers
-#
-CONFIG_BSP_USING_JLINK_TO_USART=y
-# CONFIG_BSP_USING_QSPI_FLASH is not set
-
-#
-# On-chip Peripheral Drivers
-#
-CONFIG_BSP_USING_GPIO=y
-CONFIG_BSP_USING_UART=y
-CONFIG_NRFX_USING_UART=y
-# CONFIG_NRFX_USING_UARTE is not set
-CONFIG_BSP_USING_UART0=y
-CONFIG_BSP_UART0_RX_PIN=8
-CONFIG_BSP_UART0_TX_PIN=6
-# CONFIG_BSP_USING_SAADC is not set
-# CONFIG_BSP_USING_I2C is not set
-# CONFIG_BSP_USING_SPI is not set
-# CONFIG_BSP_USING_PWM is not set
-# CONFIG_BSP_USING_WDT is not set
-# CONFIG_BSP_USING_ONCHIP_RTC is not set
-# CONFIG_BSP_USING_ON_CHIP_FLASH is not set
-
-#
-# MCU flash config
-#
-CONFIG_MCU_FLASH_START_ADDRESS=0x00000000
-CONFIG_MCU_FLASH_SIZE_KB=1024
-CONFIG_MCU_SRAM_START_ADDRESS=0x20000000
-CONFIG_MCU_SRAM_SIZE_KB=256
-CONFIG_MCU_FLASH_PAGE_SIZE=0x1000
-CONFIG_BLE_STACK_USING_NULL=y
-# CONFIG_BSP_USING_SOFTDEVICE is not set
-# CONFIG_BSP_USING_NIMBLE is not set
-CONFIG_NRFX_CLOCK_ENABLED=1
-CONFIG_NRFX_CLOCK_DEFAULT_CONFIG_IRQ_PRIORITY=7
-CONFIG_NRFX_CLOCK_CONFIG_LF_SRC=1
-CONFIG_NRFX_UART_ENABLED=1
-CONFIG_NRFX_UART0_ENABLED=1
-CONFIG_NRFX_GPIOTE_ENABLED=1

bsp/nrf5x/nrf52840/Kconfig

@@ -14,8 +14,9 @@ config PKGS_DIR
     string
     option env="PKGS_ROOT"
     default "packages"
-
+    
+source "board/Kconfig"
 source "$RTT_DIR/Kconfig"
 source "$PKGS_DIR/Kconfig"
-source "board/Kconfig"
+
 

bsp/nrf5x/nrf52840/applications/application.c

@@ -6,25 +6,24 @@
  * Change Logs:
  * Date           Author       Notes
  * 2020-04-29     supperthomas first version
+ * 2021-06-26     supperthomas fix led
  *
  */
 
 #include <rtthread.h>
 #include <rtdevice.h>
-#define DK_BOARD_LED_1  13
-#define DK_BOARD_LED_2  14
 
 int main(void)
 {
     int count = 1;
-    rt_pin_mode(DK_BOARD_LED_1, PIN_MODE_OUTPUT);
+    rt_pin_mode(RT_BSP_LED_PIN, PIN_MODE_OUTPUT);
 
     while (count++)
     {
-        rt_pin_write(DK_BOARD_LED_1, PIN_HIGH);
+        rt_pin_write(RT_BSP_LED_PIN, PIN_HIGH);
         rt_thread_mdelay(500);
 
-        rt_pin_write(DK_BOARD_LED_1, PIN_LOW);
+        rt_pin_write(RT_BSP_LED_PIN, PIN_LOW);
         rt_thread_mdelay(500);
     }
     return RT_EOK;

bsp/nrf5x/nrf52840/board/Kconfig

@@ -15,19 +15,32 @@ choice
     default BSP_BOARD_PCA_10056
 
     config BSP_BOARD_PCA_10056
+        select BSP_USING_UART
+        select BSP_USING_UART0
         bool "NRF52840 pca10056 "
-        
+
+    config BSP_BOARD_ARDUINO_NANO_33_BLE
+        bool "Arduino Nano 33 BLE (Sense)"    
 endchoice
 
 menu "Onboard Peripheral Drivers"
     config BSP_USING_JLINK_TO_USART
         bool "Enable JLINK TO USART (uart0|RX_PIN:8|TX_PIN:6)"
         default y
+        depends on BSP_BOARD_PCA_10056
+
+    config RT_BSP_LED_PIN
+        int 
+        default 13 if BSP_BOARD_PCA_10056
+        default 16 if BSP_BOARD_ARDUINO_NANO_33_BLE
+        depends on BSP_USING_GPIO
+
 
     menuconfig BSP_USING_QSPI_FLASH
         select PKG_USING_FAL
         bool "Enable QSPI FLASH(MX25R64 8MB)"
         default n
+        depends on BSP_BOARD_PCA_10056
 
         if BSP_USING_QSPI_FLASH
             config NRFX_QSPI_ENABLED
@@ -89,8 +102,6 @@ menu "On-chip Peripheral Drivers"
 		endchoice
 		endif
         if BSP_USING_UART&&NRFX_USING_UART
-
-
             config BSP_USING_UART0
                 bool "Enable UART0"
                 default y 

bsp/nrf5x/nrf52840/board/board.c

@@ -6,6 +6,7 @@
  * Change Logs:
  * Date           Author       Notes
  * 2020-04-29     supperthomas first version
+ * 2020-04-29     supperthomas fix component init
  *
  */
 #include <rtthread.h>
@@ -60,17 +61,14 @@ void rt_hw_board_init(void)
     rt_system_heap_init((void *)HEAP_BEGIN, (void *)HEAP_END);
 #endif
 
-#ifdef RT_USING_SERIAL
-    rt_hw_uart_init();
+#ifdef RT_USING_COMPONENTS_INIT
+    rt_components_board_init();
 #endif
 
 #ifdef RT_USING_CONSOLE
     rt_console_set_device(RT_CONSOLE_DEVICE_NAME);
 #endif
 
-#ifdef RT_USING_COMPONENTS_INIT
-    rt_components_board_init();
-#endif
 
 #ifdef BSP_USING_SOFTDEVICE
     extern uint32_t  Image$$RW_IRAM1$$Base;

bsp/nrf5x/nrf52840/rtconfig.h

@@ -4,6 +4,41 @@
 /* Automatically generated file; DO NOT EDIT. */
 /* RT-Thread Configuration */
 
+/* Hardware Drivers Config */
+
+#define SOC_NRF52840
+#define SOC_NORDIC
+#define BSP_BOARD_PCA_10056
+
+/* Onboard Peripheral Drivers */
+
+#define BSP_USING_JLINK_TO_USART
+#define RT_BSP_LED_PIN 13
+
+/* On-chip Peripheral Drivers */
+
+#define BSP_USING_GPIO
+#define BSP_USING_UART
+#define NRFX_USING_UART
+#define BSP_USING_UART0
+#define BSP_UART0_RX_PIN 8
+#define BSP_UART0_TX_PIN 6
+
+/* MCU flash config */
+
+#define MCU_FLASH_START_ADDRESS 0x00000000
+#define MCU_FLASH_SIZE_KB 1024
+#define MCU_SRAM_START_ADDRESS 0x20000000
+#define MCU_SRAM_SIZE_KB 256
+#define MCU_FLASH_PAGE_SIZE 0x1000
+#define BLE_STACK_USING_NULL
+#define NRFX_CLOCK_ENABLED 1
+#define NRFX_CLOCK_DEFAULT_CONFIG_IRQ_PRIORITY 7
+#define NRFX_CLOCK_CONFIG_LF_SRC 1
+#define NRFX_UART_ENABLED 1
+#define NRFX_UART0_ENABLED 1
+#define NRFX_GPIOTE_ENABLED 1
+
 /* RT-Thread Kernel */
 
 #define RT_NAME_MAX 8
@@ -160,38 +195,4 @@
 /* entertainment: terminal games and other interesting software packages */
 
 
-/* Hardware Drivers Config */
-
-#define SOC_NRF52840
-#define SOC_NORDIC
-#define BSP_BOARD_PCA_10056
-
-/* Onboard Peripheral Drivers */
-
-#define BSP_USING_JLINK_TO_USART
-
-/* On-chip Peripheral Drivers */
-
-#define BSP_USING_GPIO
-#define BSP_USING_UART
-#define NRFX_USING_UART
-#define BSP_USING_UART0
-#define BSP_UART0_RX_PIN 8
-#define BSP_UART0_TX_PIN 6
-
-/* MCU flash config */
-
-#define MCU_FLASH_START_ADDRESS 0x00000000
-#define MCU_FLASH_SIZE_KB 1024
-#define MCU_SRAM_START_ADDRESS 0x20000000
-#define MCU_SRAM_SIZE_KB 256
-#define MCU_FLASH_PAGE_SIZE 0x1000
-#define BLE_STACK_USING_NULL
-#define NRFX_CLOCK_ENABLED 1
-#define NRFX_CLOCK_DEFAULT_CONFIG_IRQ_PRIORITY 7
-#define NRFX_CLOCK_CONFIG_LF_SRC 1
-#define NRFX_UART_ENABLED 1
-#define NRFX_UART0_ENABLED 1
-#define NRFX_GPIOTE_ENABLED 1
-
 #endif