rebuild the Kconfig

bsp/nrf5x/nrf52840/.config

@@ -15,7 +15,7 @@ CONFIG_RT_THREAD_PRIORITY_32=y
 # CONFIG_RT_THREAD_PRIORITY_256 is not set
 CONFIG_RT_THREAD_PRIORITY_MAX=32
 CONFIG_RT_TICK_PER_SECOND=100
-CONFIG_RT_USING_OVERFLOW_CHECK=y
+# CONFIG_RT_USING_OVERFLOW_CHECK is not set
 CONFIG_RT_USING_HOOK=y
 CONFIG_RT_USING_IDLE_HOOK=y
 CONFIG_RT_IDLE_HOOK_LIST_SIZE=4
@@ -29,18 +29,7 @@ CONFIG_RT_TIMER_THREAD_STACK_SIZE=512
 #
 # CONFIG_RT_KSERVICE_USING_STDLIB is not set
 # CONFIG_RT_KSERVICE_USING_TINY_SIZE is not set
-CONFIG_RT_DEBUG=y
-# CONFIG_RT_DEBUG_COLOR is not set
-# CONFIG_RT_DEBUG_INIT_CONFIG is not set
-# CONFIG_RT_DEBUG_THREAD_CONFIG is not set
-# CONFIG_RT_DEBUG_SCHEDULER_CONFIG is not set
-# CONFIG_RT_DEBUG_IPC_CONFIG is not set
-# CONFIG_RT_DEBUG_TIMER_CONFIG is not set
-# CONFIG_RT_DEBUG_IRQ_CONFIG is not set
-# CONFIG_RT_DEBUG_MEM_CONFIG is not set
-# CONFIG_RT_DEBUG_SLAB_CONFIG is not set
-# CONFIG_RT_DEBUG_MEMHEAP_CONFIG is not set
-# CONFIG_RT_DEBUG_MODULE_CONFIG is not set
+# CONFIG_RT_DEBUG is not set
 
 #
 # Inter-Thread communication
@@ -48,8 +37,8 @@ CONFIG_RT_DEBUG=y
 CONFIG_RT_USING_SEMAPHORE=y
 CONFIG_RT_USING_MUTEX=y
 CONFIG_RT_USING_EVENT=y
-CONFIG_RT_USING_MAILBOX=y
-CONFIG_RT_USING_MESSAGEQUEUE=y
+# CONFIG_RT_USING_MAILBOX is not set
+# CONFIG_RT_USING_MESSAGEQUEUE is not set
 # CONFIG_RT_USING_SIGNALS is not set
 
 #
@@ -106,7 +95,7 @@ CONFIG_FINSH_CMD_SIZE=80
 # CONFIG_FINSH_USING_AUTH is not set
 CONFIG_FINSH_USING_MSH=y
 CONFIG_FINSH_USING_MSH_DEFAULT=y
-CONFIG_FINSH_USING_MSH_ONLY=y
+# CONFIG_FINSH_USING_MSH_ONLY is not set
 CONFIG_FINSH_ARG_MAX=10
 
 #
@@ -560,27 +549,44 @@ CONFIG_SOC_NRF52840=y
 CONFIG_SOC_NORDIC=y
 CONFIG_BSP_BOARD_PCA_10056=y
 
+#
+# Onboard Peripheral Drivers
+#
+CONFIG_BSP_USING_JLINK_TO_USART=y
+# CONFIG_BSP_USING_QSPI_FLASH is not set
+
 #
 # On-chip Peripheral Drivers
 #
 CONFIG_BSP_USING_GPIO=y
-CONFIG_NRFX_GPIOTE_ENABLED=1
 CONFIG_BSP_USING_UART=y
+CONFIG_NRFX_USING_UART=y
+# CONFIG_NRFX_USING_UARTE is not set
 CONFIG_BSP_USING_UART0=y
 CONFIG_BSP_UART0_RX_PIN=8
 CONFIG_BSP_UART0_TX_PIN=6
+# CONFIG_BSP_USING_SAADC is not set
+# CONFIG_BSP_USING_I2C is not set
+# CONFIG_BSP_USING_SPI is not set
+# CONFIG_BSP_USING_PWM is not set
+# CONFIG_BSP_USING_WDT is not set
+# CONFIG_BSP_USING_ONCHIP_RTC is not set
+# CONFIG_BSP_USING_ON_CHIP_FLASH is not set
 
 #
-# On-chip flash config
+# MCU flash config
 #
 CONFIG_MCU_FLASH_START_ADDRESS=0x00000000
 CONFIG_MCU_FLASH_SIZE_KB=1024
 CONFIG_MCU_SRAM_START_ADDRESS=0x20000000
 CONFIG_MCU_SRAM_SIZE_KB=256
 CONFIG_MCU_FLASH_PAGE_SIZE=0x1000
+CONFIG_BLE_STACK_USING_NULL=y
+# CONFIG_BSP_USING_SOFTDEVICE is not set
+# CONFIG_BSP_USING_NIMBLE is not set
 CONFIG_NRFX_CLOCK_ENABLED=1
 CONFIG_NRFX_CLOCK_DEFAULT_CONFIG_IRQ_PRIORITY=7
 CONFIG_NRFX_CLOCK_CONFIG_LF_SRC=1
-CONFIG_NRFX_USING_UART=y
 CONFIG_NRFX_UART_ENABLED=1
 CONFIG_NRFX_UART0_ENABLED=1
+CONFIG_NRFX_GPIOTE_ENABLED=1

bsp/nrf5x/nrf52840/board/Kconfig

@@ -2,31 +2,26 @@ menu "Hardware Drivers Config"
 
 config SOC_NRF52840
     bool
-    config SOC_NRF52840
     select RT_USING_COMPONENTS_INIT
     select RT_USING_USER_MAIN
     default y
-    config NRFX_CLOCK_ENABLED
-    int 
-    default 1
-    config NRFX_CLOCK_DEFAULT_CONFIG_IRQ_PRIORITY
-    int 
-    default 7
-    config NRFX_CLOCK_CONFIG_LF_SRC
-    int 
-    default 1  
-
     
 config SOC_NORDIC
     bool 
-    config SOC_NORDIC
     default y
 
+choice
+    prompt "Select BSP board "
+    default BSP_BOARD_PCA_10056
+
+    config BSP_BOARD_PCA_10056
+        bool "NRF52840 pca10056 "
+        
+endchoice
+
 menu "Onboard Peripheral Drivers"
     config BSP_USING_JLINK_TO_USART
         bool "Enable JLINK TO USART (uart0|RX_PIN:8|TX_PIN:6)"
-        select BSP_USING_UART
-        select BSP_USING_UART0
         default y
 
     menuconfig BSP_USING_QSPI_FLASH
@@ -68,135 +63,17 @@ menu "Onboard Peripheral Drivers"
         endif
 endmenu
 
+
 menu "On-chip Peripheral Drivers"
+
     config BSP_USING_GPIO
         bool "Enable GPIO"
         select RT_USING_PIN
         default y
-    if BSP_USING_GPIO
-        config NRFX_GPIOTE_ENABLED
-        int 
-        default 1  
-    endif
-    config BSP_USING_SAADC
-        bool "Enable SAADC"
-        select RT_USING_ADC
-        default n
-        if BSP_USING_SAADC
-                config NRFX_SAADC_ENABLED
-                int 
-                default 1  
-        endif
-    menuconfig BSP_USING_PWM
-        bool "Enable PWM"
-        select RT_USING_PWM
-        default n
-        if BSP_USING_PWM
-                config NRFX_PWM_ENABLED
-                int 
-                default 1
-                config BSP_USING_PWM0
-                    bool "Enable PWM0 bus"
-                    default y
-                if BSP_USING_PWM0
-                    config NRFX_PWM0_ENABLED
-                    int 
-                    default 1
-                    config BSP_USING_PWM0_CH0
-                        int "PWM0 channel 0 pin number set"
-                        range 0 47
-                        default 13
-                    config BSP_USING_PWM0_CH1
-                        int "PWM0 channel 1 pin number set"
-                        range 0 47
-                        default 14
-                    config BSP_USING_PWM0_CH2
-                        int "PWM0 channel 2 pin number set"
-                        range 0 47
-                        default 15
-                    config BSP_USING_PWM0_CH3
-                        int "PWM0 channel 3 pin number set"
-                        range 0 47
-                        default 16
-                endif
-                config BSP_USING_PWM1
-                    bool "Enable PWM1 bus"
-                    default n
-                if BSP_USING_PWM1
-                    config NRFX_PWM1_ENABLED
-                    int 
-                    default 1
-                    config BSP_USING_PWM1_CH0
-                        int "PWM1 channel 0 pin number set"
-                        range 0 47
-                        default 13
-                    config BSP_USING_PWM1_CH1
-                        int "PWM1 channel 1 pin number set"
-                        range 0 47
-                        default 14
-                    config BSP_USING_PWM1_CH2
-                        int "PWM1 channel 2 pin number set"
-                        range 0 47
-                        default 15
-                    config BSP_USING_PWM1_CH3
-                        int "PWM1 channel 3 pin number set"
-                        range 0 47
-                        default 16
-                endif
-                config BSP_USING_PWM2
-                    bool "Enable PWM2 bus"
-                    default n
-                if BSP_USING_PWM2
-                    config NRFX_PWM2_ENABLED
-                    int 
-                    default 1
-                    config BSP_USING_PWM2_CH0
-                        int "PWM2 channel 0 pin number set"
-                        range 0 47
-                        default 13
-                    config BSP_USING_PWM2_CH1
-                        int "PWM2 channel 1 pin number set"
-                        range 0 47
-                        default 14
-                    config BSP_USING_PWM2_CH2
-                        int "PWM2 channel 2 pin number set"
-                        range 0 47
-                        default 15
-                    config BSP_USING_PWM2_CH3
-                        int "PWM2 channel 3 pin number set"
-                        range 0 47
-                        default 16
-                endif
-                config BSP_USING_PWM3
-                    bool "Enable PWM3 bus"
-                    default n
-                if BSP_USING_PWM3
-                    config NRFX_PWM3_ENABLED
-                    int 
-                    default 1
-                    config BSP_USING_PWM3_CH0
-                        int "PWM3 channel 0 pin number set"
-                        range 0 47
-                        default 13
-                    config BSP_USING_PWM3_CH1
-                        int "PWM3 channel 1 pin number set"
-                        range 0 47
-                        default 14
-                    config BSP_USING_PWM3_CH2
-                        int "PWM3 channel 2 pin number set"
-                        range 0 47
-                        default 15
-                    config BSP_USING_PWM3_CH3
-                        int "PWM3 channel 3 pin number set"
-                        range 0 47
-                        default 16
-                endif
-        endif
-
     
     config BSP_USING_UART
 		bool "Enable UART"
-        default y
+        default n
         select RT_USING_SERIAL
 		if BSP_USING_UART
 		choice
@@ -212,17 +89,12 @@ menu "On-chip Peripheral Drivers"
 		endchoice
 		endif
         if BSP_USING_UART&&NRFX_USING_UART
-            config NRFX_UART_ENABLED
-            int 
-            default 1
+
 
             config BSP_USING_UART0
                 bool "Enable UART0"
                 default y 
                 if BSP_USING_UART0
-                    config NRFX_UART0_ENABLED
-                    int 
-                    default 1
                     config BSP_UART0_RX_PIN
                         int "uart0 rx pin number"
                         range 0 31
@@ -271,21 +143,21 @@ menu "On-chip Peripheral Drivers"
                         default 5
                 endif
         endif
-    config BSP_USING_I2C
+
+    config BSP_USING_SAADC
+        bool "Enable ADC"
+        select RT_USING_ADC
+        default n
+
+    menuconfig BSP_USING_I2C
         bool "Enable I2C"
         select RT_USING_I2C
         default n
         if BSP_USING_I2C
-            config NRFX_TWIM_ENABLED
-            int 
-            default 1
             config BSP_USING_I2C0
                 bool "Enable I2C0 bus"
-                default n
+                default y
             if BSP_USING_I2C0
-                config NRFX_TWIM0_ENABLED
-                int 
-                default 1
                 config BSP_I2C0_SCL_PIN
                     int "i2c0 scl pin number"
                     range 0 31
@@ -299,9 +171,6 @@ menu "On-chip Peripheral Drivers"
                 bool "Enable I2C1 bus"
                 default n
             if BSP_USING_I2C1
-                config NRFX_TWIM1_ENABLED
-                int 
-                default 1
                 config BSP_I2C1_SCL_PIN
                     int "i2c1 scl pin number"
                     range 0 31
@@ -312,15 +181,13 @@ menu "On-chip Peripheral Drivers"
                     default 2
             endif
         endif
-    config BSP_USING_SPI
+
+   menuconfig BSP_USING_SPI
         bool "Enable SPI"
         select RT_USING_SPI  
         default n
 
         if BSP_USING_SPI
-            config NRFX_SPI_ENABLED
-            int 
-            default 1
             config BSP_USING_SPI0
                 bool "Enable SPI0 bus"
                 default y
@@ -350,9 +217,6 @@ menu "On-chip Peripheral Drivers"
                 bool "Enable SPI1 bus"
                 default n
             if BSP_USING_SPI1
-                config NRFX_SPI1_ENABLED
-                    int "Enable SPI1 instance"
-                    default 1
                 config BSP_SPI1_SCK_PIN
                     int "SPI0 sck pin number set"
                     range 0 47
@@ -375,9 +239,6 @@ menu "On-chip Peripheral Drivers"
                 bool "Enable SPI2 bus"
                 default n
             if BSP_USING_SPI2
-                config NRFX_SPI2_ENABLED
-                    int "Enable SPI2 instance"
-                    default 1
                 config BSP_SPI2_SCK_PIN
                     int "SPI0 sck pin number set"
                     range 0 47
@@ -397,12 +258,119 @@ menu "On-chip Peripheral Drivers"
             endif
 
         endif
+
+    menuconfig BSP_USING_PWM
+        bool "Enable PWM"
+        select RT_USING_PWM
+        default n
+        if BSP_USING_PWM
+            config BSP_USING_PWM0
+                bool "Enable PWM0 bus"
+                default y
+            if BSP_USING_PWM0
+                config BSP_USING_PWM0_CH0
+                    int "PWM0 channel 0 pin number set"
+                    range 0 47
+                    default 13
+                config BSP_USING_PWM0_CH1
+                    int "PWM0 channel 1 pin number set"
+                    range 0 47
+                    default 14
+                config BSP_USING_PWM0_CH2
+                    int "PWM0 channel 2 pin number set"
+                    range 0 47
+                    default 15
+                config BSP_USING_PWM0_CH3
+                    int "PWM0 channel 3 pin number set"
+                    range 0 47
+                    default 16
+            endif
+            config BSP_USING_PWM1
+                bool "Enable PWM1 bus"
+                default n
+            if BSP_USING_PWM1
+                config NRFX_PWM1_ENABLED
+                int 
+                default 1
+                config BSP_USING_PWM1_CH0
+                    int "PWM1 channel 0 pin number set"
+                    range 0 47
+                    default 13
+                config BSP_USING_PWM1_CH1
+                    int "PWM1 channel 1 pin number set"
+                    range 0 47
+                    default 14
+                config BSP_USING_PWM1_CH2
+                    int "PWM1 channel 2 pin number set"
+                    range 0 47
+                    default 15
+                config BSP_USING_PWM1_CH3
+                    int "PWM1 channel 3 pin number set"
+                    range 0 47
+                    default 16
+            endif
+            config BSP_USING_PWM2
+                bool "Enable PWM2 bus"
+                default n
+            if BSP_USING_PWM2
+                config BSP_USING_PWM2_CH0
+                    int "PWM2 channel 0 pin number set"
+                    range 0 47
+                    default 13
+                config BSP_USING_PWM2_CH1
+                    int "PWM2 channel 1 pin number set"
+                    range 0 47
+                    default 14
+                config BSP_USING_PWM2_CH2
+                    int "PWM2 channel 2 pin number set"
+                    range 0 47
+                    default 15
+                config BSP_USING_PWM2_CH3
+                    int "PWM2 channel 3 pin number set"
+                    range 0 47
+                    default 16
+            endif
+            config BSP_USING_PWM3
+                bool "Enable PWM3 bus"
+                default n
+            if BSP_USING_PWM3
+                config BSP_USING_PWM3_CH0
+                    int "PWM3 channel 0 pin number set"
+                    range 0 47
+                    default 13
+                config BSP_USING_PWM3_CH1
+                    int "PWM3 channel 1 pin number set"
+                    range 0 47
+                    default 14
+                config BSP_USING_PWM3_CH2
+                    int "PWM3 channel 2 pin number set"
+                    range 0 47
+                    default 15
+                config BSP_USING_PWM3_CH3
+                    int "PWM3 channel 3 pin number set"
+                    range 0 47
+                    default 16
+            endif
+        endif
+
+    config BSP_USING_WDT
+        bool "Enable WDT"
+        select RT_USING_WDT
+        default n
+
+    menuconfig BSP_USING_ONCHIP_RTC
+    bool "Enable RTC"
+    select RT_USING_RTC
+    select RT_USING_LIBC
+    default n
+
+
     config BSP_USING_ON_CHIP_FLASH
         select PKG_USING_FAL
         bool "Enable on-chip FLASH"
         default n
 
-    menu "On-chip flash config"
+    menu "MCU flash config"
 
         config MCU_FLASH_START_ADDRESS  
             hex "MCU FLASH START ADDRESS"
@@ -410,71 +378,20 @@ menu "On-chip Peripheral Drivers"
 
         config MCU_FLASH_SIZE_KB  
             int "MCU FLASH SIZE, MAX size 1024 KB"
-            range 1 1024
-            default 1024		
+            default 1024
 
         config MCU_SRAM_START_ADDRESS 
             hex "MCU RAM START ADDRESS"
             default 0x20000000
 
-        config MCU_SRAM_SIZE_KB 
-            int "MCU RAM SIZE, MAX size 256 KB"
-            range 1 256
+        config MCU_SRAM_SIZE_KB  
+            int "MCU RAM SIZE"
             default 256
 
         config MCU_FLASH_PAGE_SIZE 
             hex "MCU FLASH PAGE SIZE, please not change,nrfx default is 0x1000"
-            range 0x1000 0x1000
             default 0x1000
 	endmenu
-    config BSP_USING_WDT
-        bool "Enable WDT"
-        select RT_USING_WDT
-        default n
-    if BSP_USING_WDT
-        config NRFX_WDT_ENABLED
-        int
-        default 1
-        config NRFX_WDT0_ENABLED
-        int
-        default 1
-        config NRFX_WDT_CONFIG_NO_IRQ
-        int
-        default 1
-    endif
-
-    menuconfig BSP_USING_ONCHIP_RTC
-    bool "Enable RTC"
-    select RT_USING_RTC
-    select RT_USING_LIBC
-    default n
-    if BSP_USING_ONCHIP_RTC
-        config NRFX_CLOCK_ENABLED
-        int 
-        default 1
-        config NRFX_CLOCK_DEFAULT_CONFIG_IRQ_PRIORITY
-        int
-        default 7
-        config NRFX_RTC_ENABLED
-        int 
-        default 1
-        config NRFX_RTC0_ENABLED
-        int
-        default 1
-        config NRFX_RTC1_ENABLED
-        int
-        default 1
-        config NRFX_RTC2_ENABLED
-        int
-        default 1
-        config RTC_INSTANCE_ID
-        int 
-        default 2
-        config RTC_INSTANCE_ID
-            int "select RTC instance id, must be 0, 1, 2"
-            range 0 2
-            default 2
-    endif
 
 endmenu
 
@@ -497,6 +414,166 @@ config BSP_USING_NIMBLE
     bool "use nimble stack(iot)"
 endchoice
 
+if SOC_NORDIC
+    config NRFX_CLOCK_ENABLED
+    int 
+    default 1
+    config    NRFX_CLOCK_DEFAULT_CONFIG_IRQ_PRIORITY
+    int 
+    default 7
+    config NRFX_CLOCK_CONFIG_LF_SRC
+    int 
+    default 1    
+endif
+
+if BSP_USING_UART
+    config NRFX_USING_UART
+    bool
+    default y
+    
+    config NRFX_UART_ENABLED
+    int 
+    default 1
+if BSP_USING_UART0
+    config NRFX_UART0_ENABLED
+    int 
+    default 1
+endif
+
+if NRFX_USING_UART
+    config NRFX_UART_ENABLED
+    int 
+    default 1
+endif
+
+if NRFX_USING_UARTE
+    config NRFX_UARTE0_ENABLED
+    int 
+    default 1
+endif
+
+
+endif
+
+if BSP_USING_GPIO
+    config NRFX_GPIOTE_ENABLED
+    int 
+    default 1  
+endif
+
+if BSP_USING_SAADC
+    config NRFX_SAADC_ENABLED
+    int 
+    default 1  
+endif
+
+if BSP_USING_I2C
+    config NRFX_TWIM_ENABLED
+    int 
+    default 1
+    if BSP_USING_I2C0
+        config NRFX_TWIM0_ENABLED
+        int 
+        default 1
+    endif
+
+    if BSP_USING_I2C1
+        config NRFX_TWIM1_ENABLED
+        int 
+        default 1
+    endif
+endif
+
+if BSP_USING_SPI
+    config NRFX_SPI_ENABLED
+    int 
+    default 1
+
+    if BSP_USING_SPI0
+        config NRFX_SPI0_ENABLED
+        int 
+        default 1
+    endif
+
+    if BSP_USING_SPI1
+        config NRFX_SPI1_ENABLED
+        int 
+        default 1
+    endif
+
+    if BSP_USING_SPI2
+        config NRFX_SPI2_ENABLED
+        int 
+        default 1
+    endif
+endif
+
+if BSP_USING_PWM
+    config NRFX_PWM_ENABLED
+    int 
+    default 1
+    if BSP_USING_PWM0
+        config NRFX_PWM0_ENABLED
+        int 
+        default 1
+    endif
+    if BSP_USING_PWM1
+    config NRFX_PWM1_ENABLED
+    int 
+    default 1
+    endif
+    if BSP_USING_PWM2
+        config NRFX_PWM2_ENABLED
+        int 
+        default 1
+    endif
+    if BSP_USING_PWM3
+        config NRFX_PWM3_ENABLED
+        int 
+        default 1
+    endif
+
+endif
+
+if BSP_USING_WDT
+    config NRFX_WDT_ENABLED
+    int
+    default 1
+    config NRFX_WDT0_ENABLED
+    int
+    default 1
+    config NRFX_WDT_CONFIG_NO_IRQ
+    int
+    default 1
+endif
+
+if BSP_USING_ONCHIP_RTC
+    config NRFX_CLOCK_ENABLED
+    int 
+    default 1
+    config NRFX_CLOCK_DEFAULT_CONFIG_IRQ_PRIORITY
+    int
+    default 7
+    config NRFX_RTC_ENABLED
+    int 
+    default 1
+    config NRFX_RTC0_ENABLED
+    int
+    default 1
+    config NRFX_RTC1_ENABLED
+    int
+    default 1
+    config NRFX_RTC2_ENABLED
+    int
+    default 1
+    config RTC_INSTANCE_ID
+    int 
+    default 2
+    config RTC_INSTANCE_ID
+        int
+        range 0 2
+        default 2
+endif
 
 endmenu
 

bsp/nrf5x/nrf52840/rtconfig.h

@@ -11,7 +11,6 @@
 #define RT_THREAD_PRIORITY_32
 #define RT_THREAD_PRIORITY_MAX 32
 #define RT_TICK_PER_SECOND 100
-#define RT_USING_OVERFLOW_CHECK
 #define RT_USING_HOOK
 #define RT_USING_IDLE_HOOK
 #define RT_IDLE_HOOK_LIST_SIZE 4
@@ -22,15 +21,12 @@
 
 /* kservice optimization */
 
-#define RT_DEBUG
 
 /* Inter-Thread communication */
 
 #define RT_USING_SEMAPHORE
 #define RT_USING_MUTEX
 #define RT_USING_EVENT
-#define RT_USING_MAILBOX
-#define RT_USING_MESSAGEQUEUE
 
 /* Memory Management */
 
@@ -69,7 +65,6 @@
 #define FINSH_CMD_SIZE 80
 #define FINSH_USING_MSH
 #define FINSH_USING_MSH_DEFAULT
-#define FINSH_USING_MSH_ONLY
 #define FINSH_ARG_MAX 10
 
 /* Device virtual file system */
@@ -171,27 +166,32 @@
 #define SOC_NORDIC
 #define BSP_BOARD_PCA_10056
 
+/* Onboard Peripheral Drivers */
+
+#define BSP_USING_JLINK_TO_USART
+
 /* On-chip Peripheral Drivers */
 
 #define BSP_USING_GPIO
-#define NRFX_GPIOTE_ENABLED 1
 #define BSP_USING_UART
+#define NRFX_USING_UART
 #define BSP_USING_UART0
 #define BSP_UART0_RX_PIN 8
 #define BSP_UART0_TX_PIN 6
 
-/* On-chip flash config */
+/* MCU flash config */
 
 #define MCU_FLASH_START_ADDRESS 0x00000000
 #define MCU_FLASH_SIZE_KB 1024
 #define MCU_SRAM_START_ADDRESS 0x20000000
 #define MCU_SRAM_SIZE_KB 256
 #define MCU_FLASH_PAGE_SIZE 0x1000
+#define BLE_STACK_USING_NULL
 #define NRFX_CLOCK_ENABLED 1
 #define NRFX_CLOCK_DEFAULT_CONFIG_IRQ_PRIORITY 7
 #define NRFX_CLOCK_CONFIG_LF_SRC 1
-#define NRFX_USING_UART
 #define NRFX_UART_ENABLED 1
 #define NRFX_UART0_ENABLED 1
+#define NRFX_GPIOTE_ENABLED 1
 
 #endif