Kconfig

menu "Hardware Drivers Config"

    menu "On-chip Peripheral Drivers"
        source "$BSP_DIR/../libraries/n9h30/rtt_port/Kconfig"
    endmenu

    menu "On-board Peripheral Drivers"

        config BSP_USING_CONSOLE
            bool "Enable UART0 for RTT Console(uart0)"
            select BSP_USING_UART
            select BSP_USING_UART0
            default y

        config BOARD_USING_IP101GR
            bool "Enable ethernet phy supporting(over emac/mdio)"
            select BSP_USING_EMAC
            select BSP_USING_EMAC0
            select BSP_USING_EMAC1
            default n

        config BOARD_USING_NAU8822
            bool "NAU8822 Audio Codec supporting(over i2s, i2c0)"
            select NU_PKG_USING_NAU8822
            select BSP_USING_I2C0
            select BSP_USING_I2S
            select BSP_USING_I2S0
            default n

        config BOARD_USING_STORAGE_SDCARD
            bool "SDCARD supporting(over sdh_p0)"
            select BSP_USING_SDH
            select BSP_USING_SDH0
            default y

        config BOARD_USING_STORAGE_SPIFLASH
            bool "SPIFLASH supporting(over qspi0)"
            select BSP_USING_QSPI
            select BSP_USING_QSPI0
            default y

        config BOARD_USING_BUZZER
            bool "BUZZER.(over pwm0_ch1)"
            select BSP_USING_PWM
            select BSP_USING_PWM0
            default n

        config BOARD_USING_USB0_DEVICE_HOST
            select BSP_USING_USBH
            select BSP_USING_USBD
            bool "Enable USB0 Device/Host"
            help
                Choose this option if you need USB device or host function mode.
                    If you need USB host, please remember short to ground on JP1 jumper.

        config BOARD_USING_USB1_HOST
            select BSP_USING_USBH
            bool "Enable USB1 Host"
            help
                Choose this option if you need USB1 HOST.

    endmenu

    menu "Board extended module drivers"

        choice
            prompt "Select LCD panel devices.(Over VPOST)"

                config BOARD_USING_LCM_FW070TFT_WVGA
                    bool "NuDesign TFT-LCD7-WVGA"
                    select BSP_USING_VPOST
                    select LCM_USING_FW070TFT
                    default y
                    help
                        Choose this option if you use 7" 800x480x32b LCD panel.

                config BOARD_USING_LCM_FW043TFT_HVGA
                    bool "NuDesign TFT-LCD43-HVGA"
                    select BSP_USING_VPOST
                    select LCM_USING_FW043TFT
                    help
                        Choose this option if you use 4.3" 480x272x32b LCD panel.

                config BOARD_USING_LCM_FW070TFT_WSVGA
                    bool "NuDesign TFT-LCD7-WSVGA"
                    select BSP_USING_VPOST
                    select LCM_USING_FW070TFT_WSVGA
                    help
                        Choose this option if you use 7" 1024x600x32b LCD panel.
        endchoice

        choice
            prompt "Select Touch devices."

                config BOARD_USING_ADCTOUCH
                    bool "ADC touching"
                    select BSP_USING_ADC_TOUCH
                    default y
                    help
                        Choose this option if you use internal ADC touching function.

                config BOARD_USING_GT911
                    bool "GT911 TSC"
                    select BSP_USING_I2C
                    select BSP_USING_I2C0
                    select PKG_USING_GT911
                    help
                        Choose this option if you use GT911 external TSC touching function.

        endchoice

    endmenu

    source "$BSP_DIR/../libraries/nu_packages/Kconfig"

endmenu