There are three Kconfig entries with "--- help ---" attributes, and over
2000 Kconfig entries with "---help---" attributes.  Apparently the three
attributes with embedded spaces are valid. Still, I see little reason
for using this obscure variant. And replacing those three attributes
with the common variant makes grepping Kconfig files for help texts a
bit easier too.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The ath79 usb driver doesn't do anything special and is now converted
to the generic ehci and ohci driver.
This was tested on a TP-Link TL-WR1043ND (AR9132)
Acked-by: NGabor Juhos <juhosg@openwrt.org>
CC: Imre Kaloz <kaloz@openwrt.org>
CC: linux-mips@linux-mips.org
CC: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds a generic driver for platform devices. It works like the PCI
driver and is based on it. This is for devices which do not have an own
bus but their EHCI controller works like a PCI controller. It will be
used for the Broadcom bcma and ssb USB EHCI controller.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds a generic driver for platform devices. It works like the PCI
driver and is based on it. This is for devices which do not have an own
bus but their OHCI controller works like a PCI controller. It will be
used for the Broadcom bcma and ssb USB OHCI controller.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds a fairly simple xhci-platform driver support. Currently it is
used by the dwc3 driver for supporting host mode.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

This ehci driver is mainly designed to support host controller found on
Marvell PXA and MMP Soc series.
Add the dependence to avoid the potential build failure which may
include two EHCI controller drivers.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since ehci-mv.c can cover Marvell PXA and MMP series including PXA168,
so this driver seems redundant now.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Cc: <tanmay.upadhyay@einfochips.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix kconfig warnings and build errors in UWB/WUSB/USB_HWA etc.
by making all of these related symbols depend on UWB.

warning: (USB_WHCI_HCD && USB_HWA_HCD) selects USB_WUSB which has unmet direct dependencies (USB_SUPPORT && EXPERIMENTAL && USB && PCI && UWB)
warning: (USB_HWA_HCD) selects UWB_HWA which has unmet direct dependencies (UWB && USB)

which lead to:

ERROR: "uwb_rsv_establish" [drivers/usb/wusbcore/wusbcore.ko] undefined!
ERROR: "uwb_pal_register" [drivers/usb/wusbcore/wusbcore.ko] undefined!
ERROR: "uwb_rsv_get_usable_mas" [drivers/usb/wusbcore/wusbcore.ko] undefined!
ERROR: "uwb_rsv_destroy" [drivers/usb/wusbcore/wusbcore.ko] undefined!
ERROR: "uwb_radio_stop" [drivers/usb/wusbcore/wusbcore.ko] undefined!
ERROR: "uwb_rsv_terminate" [drivers/usb/wusbcore/wusbcore.ko] undefined!
ERROR: "uwb_pal_unregister" [drivers/usb/wusbcore/wusbcore.ko] undefined!
ERROR: "uwb_pal_init" [drivers/usb/wusbcore/wusbcore.ko] undefined!
ERROR: "uwb_rc_reset_all" [drivers/usb/wusbcore/wusbcore.ko] undefined!
ERROR: "uwb_radio_start" [drivers/usb/wusbcore/wusbcore.ko] undefined!
ERROR: "uwb_rsv_create" [drivers/usb/wusbcore/wusbcore.ko] undefined!
ERROR: "uwb_rc_put" [drivers/usb/host/whci/whci-hcd.ko] undefined!
ERROR: "uwb_rc_get_by_grandpa" [drivers/usb/host/whci/whci-hcd.ko] undefined!
ERROR: "__umc_driver_register" [drivers/usb/host/whci/whci-hcd.ko] undefined!
ERROR: "umc_driver_unregister" [drivers/usb/host/whci/whci-hcd.ko] undefined!
ERROR: "whci_wait_for" [drivers/usb/host/whci/whci-hcd.ko] undefined!
ERROR: "uwb_rc_get_by_grandpa" [drivers/usb/host/hwa-hc.ko] undefined!
ERROR: "uwb_rc_put" [drivers/usb/host/hwa-hc.ko] undefined!
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Distinguish Kconfig text by providing the Freescale family name.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 0dd2b62a.

It causes a bunch of Kconfig errors:

drivers/usb/host/Kconfig:559:error: recursive dependency detected!
drivers/usb/host/Kconfig:559:	symbol USB_HWA_HCD depends on UWB
drivers/uwb/Kconfig:5:	symbol UWB is selected by USB_WUSB
drivers/usb/wusbcore/Kconfig:4:	symbol USB_WUSB is selected by USB_HWA_HCD

showing that this really wasn't the correct fix at all.

Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix the following build warning:

warning: (USB_HWA_HCD) selects UWB_HWA which has unmet direct dependencies (UWB && USB)
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds USB OHCI driver for Samsung EXYNOS SoCs.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds support for EHCI compliant HSUSB Host controller found
on Marvell Socs.

It fits both OTG and SPH controller on marvell Socs, including
PXA9xx/MMP2/MMP3/MGx.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Also make the USB_EHCI_ATH79 selectable for the AR933X SoCs.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Kathy Giori <kgiori@qca.qualcomm.com>
Cc: "Luis R.  Rodriguez" <rodrigue@qca.qualcomm.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2529/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This is mod_host prototype support for renesas_usbhs driver.
It doesn't support USB-Hub, and USB-DMAC for now.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

to make it look like OHCI and EHCI, we introduce
that symbol and USB_XHCI_HCD depend on that
instead of PCI.

[bigeasy@linutronix.de: wire up USB_ARCH_HAS_HCD]
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

the MACH_MX* macros are scheduled for removal, so just depend
on ARCH_MXC instead. The Kconfig text makes it clear on which
SoC the driver runs on.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- Add EHCI Host controller driver
- Add wrapper that creates resources for host controller driver

v2 - Call clk_put() after clk_disable() in probe function
Signed-off-by: NTanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for big endian GRUSBHC UHCI controllers.
The HCD bus glue will probe the register interface to determine
the endianness of the controller.

Tested on GR-LEON4-ITX board which has a controller with little endian
interface and on custom LEON3 board with a BE controller.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for universal host controllers that use
big endian descriptors. Support for BE descriptors requires a non-PCI
host controller. For kernels with PCI-only UHCI there should be no
change in behaviour.

This patch tries to replicate the technique used to support BE descriptors
in the EHCI HCD. Parts added to uhci-hcd.h are basically copy'n'paste from
ehci.h.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for big endian mmio to the UHCI HCD. Big endian
mmio is supported by adding a flag bit to the UHCI HCD replicating the
solution used in the EHCI HCD.

When adding big endian support this patch also adds a check to see if we
need to support HCs with PCI I/O registers when we support HCs with MMIO.

This patch also adds 'const' to the register access functions' uhci_hcd
argument.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the UHCI part of the GRLIB GRUSBHC controller
found on some LEON/GRLIB SoCs.

The UHCI HCD previously only supported controllers connected over PCI.
This patch adds support for the first non-PCI UHCI HC. I have tried to
replicate the solution used in ehci-hcd.c.

Tested on GR-LEON4-ITX board (LEON4/GRLIB with GRUSBHC) and x86 with Intel
UHCI HC.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch is part of a series that extend the UHCI HCD to support
non-PCI host controllers.

This patch also extends the uhci_{read,write}* functions to allow accesses
to registers not mapped into PCI I/O space. This extension also includes
the addition of a void __iomem pointer to the uhci structure.

A new Kconfig option is added to signal that the system has a non-PCI HC.
If this Kconfig option is set, uhci-hcd.c will include generic reset functions
for systems that do not make use of keyboard and mouse legacy support. PCI
controllers will still always use the reset functions from pci-quirks

This patch is followed by a patch that adds bus glue for the first non-PCI
UHCI HC.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the GRLIB GRUSBHC EHCI controller from
Aeroflex Gaisler. The controller is typically found on LEON/GRLIB
SoCs.

Tested on GR-LEON4-ITX with with little endian interface and on
LEON3 system on GR-PCI-XC5V development board for big endian
controller.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Atheros AR71XX/AR7240 SoCs have a built-in OHCI controller.
This patch adds the necessary glue code to make the generic OHCI
driver usable for them.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Atheros AR71XX/AR91XX SoCs have a built-in EHCI controller.
This patch adds the necessary glue code to make the generic EHCI
driver usable for them.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds host USB high speed driver for samsung S5P series. This
is initial driver and we need additional implementation to support some
functions like power management.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some bluetooth dongles want ISO mode, and the limited support that the
sl811 offers today is sufficient.  So add a Kconfig option for people
to optionally get access to the partial functionality.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

The Tegra 2 SoC has 3 EHCI compatible USB controllers. This patch adds
the necessary glue to allow the ehci-hcd driver to work on Tegra 2
SoCs.

The platform data is used to configure board-specific phy settings and
to configure the operating mode, as one of the ports may be used as a otg
port. For additional power saving, the driver supports powering down the
phy on bus suspend when it is used, for example, to connect an internal
device that use an out-of-band remote wakeup mechanism (e.g. a gpio).
Signed-off-by: NBenoit Goby <benoit@android.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver is used across all MSM SoCs.  Hence give a generic name.
All Functions and strutures are also using "msm_otg" as prefix.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The SH EHCI/OHCI driver hardcoded the CPU type in {ehci,ohci}-hcd.c.
So if we will add the new CPU, we had to add to the hcd driver each time.
The patch adds the CONFIG_USB_{EHCI,OHCI}_SH configuration. So if we
want to use the SH EHCI/OHCI, we only enable the configuration.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch add bus glue for USB controller commonly found in PMC-Sierra MSP71xx family of SoC's.
Signed-off-by: NAnoop P A <anoop.pa@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the below compilation errors.

  CC      drivers/usb/gadget/ci13xxx_msm.o
  CC      net/mac80211/led.o
  drivers/usb/gadget/ci13xxx_msm.c: In function 'ci13xxx_msm_notify_event':
  drivers/usb/gadget/ci13xxx_msm.c:42: error: 'USB_AHBBURST' undeclared (first use in this function)
  drivers/usb/gadget/ci13xxx_msm.c:42: error: (Each undeclared identifier is reported only once
  drivers/usb/gadget/ci13xxx_msm.c:42: error: for each function it appears in.)
  drivers/usb/gadget/ci13xxx_msm.c:43: error: 'USB_AHBMODE' undeclared (first use in this function)
make[4]: *** [drivers/usb/gadget/ci13xxx_msm.o] Error 1
make[3]: *** [drivers/usb/gadget] Error 2

MSM USB driver is not supported on boards like trout (MSM7201) which
has an external PHY.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Enable runtime PM and mark no_callbacks flag.  OTG device, parent of
HCD takes care of putting hardware into low power mode.  Adjust port
power wakeup flags during system suspend and resume.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for EHCI compliant HSUSB Host controller found
on MSM chips.  The root hub has a single port and TT is built into it.
This driver depends on OTG driver for PHY initialization, clock
management and powering up VBUS.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Introduce the CONFIG_USB_EHCI_HCD_OMAP option to select
EHCI support on OMAP3 and later chips. This scales better
than having a long line of dependencies for each new OMAP
with EHCI support.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>

The CNS3XXX SOC has include USB EHCI and OHCI compatible controllers.
This patch adds the necessary glue logic to allow ehci-hcd and ohci-hcd
drivers to work on CNS3XXX

The EHCI and OHCI controllers share a common clock control and reset
bit, therefore additional check for the timming of enabling and disabling
is required. The USB bit of PLL Power Down Control is also shared by OTG,
24MHzUART clock, Crypto clock, PCIe reference clock, and Clock Scale
Generator. Therefore we only ensure it is enabled, while not disabling it.
Signed-off-by: NMac Lin <mkl0301@gmail.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

Commit 126512e3 added support for FSL's USB
controller on powerpc. In this commit the Open Firmware code was selected
and compiled unconditionally.

This breaks on ARM systems from FSL which use the same driver (.i.e. the i.MX
series), because ARM don't have OF support (yet). This patch fixes the problem
by only selecting the OF code on systems with Open Firmware support.
Reported-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Compile-Tested-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The OCTEON II SOC has USB EHCI and OHCI controllers connected directly
to the internal I/O bus.  This patch adds the necessary 'glue' logic
to allow ehci-hcd and ohci-hcd drivers to work on OCTEON II.

The OCTEON normally runs big-endian, and the ehci/ohci internal
registers have host endianness, so we need to select
USB_EHCI_BIG_ENDIAN_MMIO.

The ehci and ohci blocks share a common clocking and PHY
infrastructure.  Initialization of the host controller and PHY clocks
is common between the two and is factored out into the
octeon2-common.c file.

Setting of USB_ARCH_HAS_OHCI and USB_ARCH_HAS_EHCI is done in
arch/mips/Kconfig in a following patch.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-usb@vger.kernel.org
To: dbrownell@users.sourceforge.net
Patchwork: http://patchwork.linux-mips.org/patch/1675/Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>